Samsung Hp-p5091 Plasma Display Owners Instructions

71
5
At this point, one of the TV-Ratings is selected.
Press the ENTER button. Depending on your existing 
setup, a symbol will be selected.
(Blank = Unblocked, = Blocked)
While “ ” is selected, press the ENTER button 
to block or unblock the category.
To select a different TV-Rating, press the ▲or ▼
button and then repeat the process.
Note 1: The TV-Y, TV-Y7, TV-G, TV-PG, TV-14 and TV-MA have additional options. 
See the next step to change any of the following sub-ratings:
FV: Fantasy violence
D:...

72
How to Set up Restrictions using the MPAA Ratings: G, PG, PG-13, R, NC-17, X, NR
The MPAA rating system uses the Motion Picture Association of America (MPAA) system, and its main application
is for movies. When the V-Chip lock is on, the TV will automatically block any programs that are coded with 
objectionable ratings (either MPAA or TV-Ratings).
1
Press the MENU button.Press the ▲or ▼button to
select “Preference”, then press the ENTER button. 
2
Press the ▲or ▼button to select “V-Chip”, then press...

73
How to Reset the TV after the V-Chip Blocks a Channel (“Emergency Escape”)
If the TV is tuned to a restricted channel, the V-Chip will block it. The screen will go blank and the
following message will appear: 
1
Press the ENTER button.  
2 
Enter your PIN number.
To resume normal viewing, tune to a different channel using the number buttons. 
Under certain conditions (depending on the rating of the local TV programs) the V-Chip might lock out
all the channels. In this case, use the V-Chip function for...

74
Your WIRELESS HOME AV CENTER has an Electronic
Program Guide (EPG) to help you navigate through all the 
possible viewing options. 
The EPG supplies information, such as program lists, 
start and end times of all available channels.
In addition, the detailed information about the program is 
often available in the EPG. (The availability and the amount 
of program details will vary depending on the broadcaster.)
Viewing the Electronic Program Guide (EPG)
ADisplays which channel is currently selected to...

75
1 
Press the MENU button. Press the ▲or ▼button to select “Guide”, then press the ENTER 
button.
2
Press the ▲or ▼button to select the “Default Guide”, then press the ENTER button.
3
Press the ▲or ▼button to alternate between “Mini Guide” and “Full Guide” and press 
the ENTER button.
Viewing the Information about One Channel
1 
Press the MENU button. Press the ▲or ▼button to select “Guide”, then press the ENTER 
button.
2
Press the ▲or ▼button to select the “Mini Guide”, then press the ENTER button....

PLASMA DISPLAY PANEL
with WIRELESS HOME AV CENTER
Appendix
Troubleshooting............................................................................78
Care and Maintenance ................................................................81
Specifications ..............................................................................82 

78
Troubleshooting
If the TV seems to have a problem, first try this list of possible problems and solutions. If none of these 
troubleshooting tips apply, then call your nearest service center.
WIRELESS HOME AV CENTER
ProblemPossible Solution
Poor picture qualityTry another channel.
Adjust the antenna.
Check all wire connections. 
Poor sound quality or no sound.Try another channel.
Adjust the antenna.
Make sure the “MUTE” button is off.
No picture or sound.Try another channel.
Make sure the Set-Top Box...

79
PDP (Continued)
ProblemPossible Solution
PDP set is turned on and the message
“No Wireless Signal or Please Check
WIRELESS HOME AV CENTER
Power” appears.
Cause 1: The WIRELESS HOME AV
CENTER is turned off. 
Cause 2: The message still appears
despite the AV Center is on. Solution 1: Turn on the PDP set and then turn on the AV
Center as they have separate power supplies. 
Solution 2: Check if AV Receiver’s LED at the top of PDP
set and the AV Center’s wireless LED are ON and green.
If both are OFF,...

80
PDP (Continued)
ProblemPossible Solution
There is no signal in a digital chan-
nel, and messages “Searching for
Signals” followed by “No Signal”
appear.
Cause: Channels have been stored
using Auto Memorize but the 
broadcasting companies are not
sending the corresponding signals.
Or External Input has been selected
but there is no signal.Solution: Select an alternative channel or switch the 
external input source.
The message “Not supported sound
format” appears.
Cause: Digital Audio rather than 
AC-3...