Samsung Hp-p5091 Plasma Display Owners Instructions

							1 
Remove the screws on the rear of the PDP panel.
2 
Connect insulation holders to screws (see the illustration below).
• If you are uncertain about installation, hire an Installation Specialist to install the 
wall mount bracket.
• Be sure to check that the insulation holders are completely secured on both the left
and right side after hanging the PDP on the wall mount bracket.
• Be careful to avoid getting your fingers caught during installation.
• Make sure the wall attachment panels are tightened. Otherwise the PDP may fall.
3 
Tighten the screws of the Insulation holders to the back of the PDP. 
Note
•A 5 inch(12.7 cm) gap is needed between the back of the Plasma TV and the wall.
4
Put the 4 insulation holders on the PDP in the grooves of the wall mount bracket and
pull down on the PDP (Œ) to secure it to the wall mount bracket. (´) Tighten the 
screws as shown (ˇ) so that the PDP cannot be separated from wall mount bracket. 
Fixing the PDP panel to the wall attachment panel bracket
PDP panel
Wall attachment panel bracketWall
Œ
´ˇ
31 
						

							32
1. Contact an authorized technician when installing the wall attachment panel.
2. After hanging the PDP panel on the wall attachment panel, make sure that the Insulation
holders are secure.
3. Be careful not to get your fingers caught during installation.
4. Make sure the wall attachment panel brackets are tightened. Otherwise, the PDP panel may 
fall down.
5. Please secure the mounting bracket on the wall surface after setting its angle at 0°.
How to Adjust Mounting Angle
Note  Note : Please secure the mounting bracket on the wall surface after setting its angle at 0°
Factory default How to Adjust Mounting Angle
The wall mount bracket is sold separately.
Please tighten the captive screw in the direction
of the arrow after assembling the bracket.Hold onto the middle of the PDP to adjust 
the angle (not the sides of the PDP).
1
Secure the PDP to the wall mount bracket.
(Please refer to the following instructions.)
2
Set the angle by pulling the upper end of the PDP attached to bracket in 
the direction of the arrow.
3
The angle can be adjusted from 0° to 15° by ±2°.
Change Angle
! Hold the top side of the Set and pull it to the front. 
@ Before connecting cables, hold the bottom side of the Set and pull it to the front.
# After connecting cables, push the bottom side of the Set back in.
$ Push the topside of the Set back in.
% Adjust the angle of the Set by holding the top side of the Set. (Caution: Be careful not to hit the Receiver on top of 
the PDP Set against the wall when you connect the cables. Follow the order indicated in the provided diagram above 
for cable connections.) 
Connecting External Devices to the PDP
Pull
Pull!@
Push
#Push$% 
						

							PLASMA DISPLAY PANEL
with WIRELESS HOME AV CENTER
Operation
Turning the PDP On and Off ..........................................................34
Memorizing the Channels..............................................................35
Using the On-Screen Help ............................................................40
Setting your Favorite Channels ......................................................41
Fine Tuning Channels ....................................................................42
Setting the Date and Time..............................................................43
Checking the Digital-Signal Reception ............................................44
Setting Up your Remote Control ....................................................45 
						

							34
Turning the PDP On and Off
Press the POWER ON button on the remote control. 
The PDP will be turned on and you will be ready to use its
features. You can also use the POWER ( ) button on the
front of the PDP. You can use the POWER ON button to turn
on the WIRELESS HOME AV CENTER. The WIRELESS
HOME AV CENTER and the PDP each have their own
respective POWER ON/OFF button, but when you turn off
the PDP, the WIRELESS HOME AV CENTER will turn off also.
Note 
•If your PDP isn’t turned on when the POWER ON button is pressed: Press the MODEbutton to check
if the TV mode has been chosen ( ). 
Viewing the Menus and Displays
Your PDP has a simple, easy-to-use menu system that appears on the PDP screen. This system makes it convenient
and fast to use features on the PDP. Your PDP also lets you display the status of many of your PDP’s features.
Viewing the Menus
1 
With power on, press the MENU button on the remote
control. The main menu appears on the screen. 
The Guide menu is selected. 
2
Press the ▲or ▼button to move items in the menu.
Press the œ/
√/
ENTER buttons to display, change, or 
use the selected items. Press the ENTER ( ) button to 
enter items in the menu. On screen menus disappear 
from the screen automatically after about 2 minutes, 
or you can press the MENU or EXIT button on your 
remote control to exit the menu.
Displaying Status Information
Press the INFO button on the remote control. The PDP will
display the channel, MTS, rating, and caption information.
Mini Guide√
Full Guide√
Remind List√
Default Guide : Mini Guide√
Guide
MoveEnterReturn
Air 10
SD
MonoNo title
No Detail Information
8:15 PM Fri Nov 09
DTV Air
13-1              
TV #1
SD
EnglishLife on Venus Avenue
10:00 am - 11:00 am
No Detail Information10:44 AM Wed Sep 02
TV
Turning the PDP On and Off 
						

							35
Memorizing the Channels
Your PDP can memorize and store all of the available channels for both “off-air” (antenna)
and cable channels. After the available channels are memorized, use the CH and CH
buttons to scan through the channels. This eliminates the need to change channels by entering
the channel digits. There are three steps for memorizing channels: selecting a broadcast
source, memorizing the channels (automatic) and adding and deleting channels (manual).
Selecting the Video Signal-source
Before your television can begin memorizing the available channels, you must specify the type of signal
source that is connected to the WIRELESS HOME AV CENTER (i.e., an antenna or a cable system).
1 
Press the MENU button. Press the ▲or ▼button to
select “Channel”, then press the ENTER button.
2 
Press the ▲or ▼button to select “Select Antenna”,
then press the ENTER button.
3 
Press the ▲or ▼button to select “Air” or “Cable”,
then press the ENTER button.
4 
Press the MENU button to exit.
Select Antenna : Air√
Auto Program√
Add/Delete√
Fine Tune√
Signal Strength√
Channel TV
MoveEnterReturn
Select Antenna :Cable
Auto Program
Add/Delete
Fine Tune
Signal Strength
Channel TV
MoveEnterReturn
Air
Cable
Select Antenna :Cable
Auto Program
Add/Delete
Fine Tune
Signal Strength
Channel TV
MoveEnterReturn
Air
Cable 
						

							36
Storing Channels in Memory (Automatic Method)
1
First, select the correct antenna (Air and Cable).
See steps on previous page. Press the MENU button.
Press the ▲or ▼ button to select “Channel”, 
then press the ENTER button. 
2
Press the ▲or ▼button to select “Auto Program”,
then press the ENTER button.
➤ ➤Quick way to access the Automatic Channel Setting: 
Just press the “AUTO PROG.” button on the remote control.
3
Press the ▲or ▼ button to select the correct signal 
(Air, STD, HRC, and IRC). Select an option and then 
press the ENTER button.
If you are connected to an antenna (Air), leave
“Air” displayed. If you are connected to a cable, 
press the ▲or ▼ button to display the type of cable 
system “STD”, “HRC” or “IRC”. (If you are not sure 
which type of cable system you have, contact your 
cable company).
4
Press the ENTER button. 
The PDP will begin memorizing all of the available 
channels. After all the available channels are stored, 
the Auto program menu reappears. Press the MENU 
button to stop.
Note
•Auto Program may take a few minutes to process.
Select Antenna : Air√
Auto Program√
Add/Delete√
Fine Tune√
Signal Strength√
Channel TV
MoveEnterReturn
Select Antenna : Air√
Auto Program√
Add/Delete√
Fine Tune√
Signal Strength√
Channel TV
MoveEnterReturn
Air
STD
HRC
IRC
Auto Program TV
MoveEnterReturn
Start
Auto Program
EnterReturn
Air Ch   23
Stop
Auto Program
EnterReturn
It will take about several minutes.
Would you like to continue? 
						

							37
Adding and Deleting Channels (Manual Method)
1 
Use the number buttons to directly select the channel
that will be added or deleted.
Ex) Channel “11”
2 
Press the ADD/DEL button, then press the ENTER 
button. Repeatedly pressing this button will alternate
between “Add” and “Delete”.
3 
Press the MENU button to exit.
Note
•You can view any channel (including an erased channel) by using the number buttons on the 
remote control.
Air  11
Press ENTER to delete the channelIn Memory
Add/Delete
Air 11
Mono
Delete
EnterChangeExit 
						

							38
Changing Channels
Using the Channel Buttons
Press the CH  or CH  button to change channels.
When you press the CH  or CH  button, the PDP changes 
channels in sequence. You will see all the channels that the PDP 
has memorized. (The PDP must have memorized at least three 
channels.) 
You will not see channels that were either erased or not memorized.
Directly Accessing Channels
Press the number buttons to go directly to a channel. For example, 
to select channel 27, press “2” then “7”. 
The TV will change channels when you press the second number.
When you use the number buttons, you can directly select channels that
were either erased or not memorized. To change to single-digit channels
(0~9) faster, press “0” before the single digit. (For channel “4” press “0”,
then “4”.) 
Using the PRE-CH button to select the previous channel
Press the PRE-CH button. The TV will switch to the last channel
viewed.
To quickly switch between two channels that are far apart, tune to
one channel, then use the number button to select the second 
channel. Then, use the PRE-CH button to quickly alternate between
them.
Using the FAV. CH button
Press to switch among your favorite channels (see “Setting your
Favorite Channels” on page 41). 
						

							39
Adjusting the Volume
Using the Volume Buttons
Press the VOL or VOL  button to increase or decrease the 
volume. 
Using Mute
Using the MUTE Button
At any time, you can temporarily cut off the sound using the MUTE
button.
1
Press the MUTE button and the sound cuts off. 
2
The word “Mute” will appear in the lower-left 
corner of the screen.
3
To turn mute off, press the MUTE button again, 
or simply press the VOL  or VOL  button.
Mute 
						

							40
To turn the on-screen help on :
1
Press the MENU button. Press the ▲or ▼button to 
select “Preference”, then press the ENTER button. 
2
Press the ▲or ▼button to select “Function Help”, 
then press the ENTER button. 
The on-screen help appears.
3
Press the ▲or ▼button to select “On” or “Off”.
Press the ▲or ▼button to highlight each of icons 
and read the description of the features that each 
icon represents.
4
Press the ENTER button. 
To turn the on-screen help off :
Press the ▲or ▼button to select “Off” and press the ENTER button. 
The on-screen help will disappear.
Using the On-Screen Help
Favorite Channels√
Multi-Track Options√
V-Chip√
Caption√
Function Help : On√
Preference TV
MoveEnterReturn
Favorite Channels
Multi-Track Options
V-Chip
Caption
Function Help :On
Preference TV
MoveEnterReturn
On
Off
Favorite Channels
Multi-Track Options
V-Chip
Caption
Function Help :On
Preference TV
MoveEnterReturn
Activates Help functions for menu items.
On
Off