Home > Runco > Display > Runco XP-50DHD Plasma Display User Manual

Runco XP-50DHD Plasma Display User Manual

Here you can view all the pages of manual Runco XP-50DHD Plasma Display User Manual. The Runco manuals for Display are available online for free. You can easily download all the documents as PDF.

Page 61

Operation
PlasmaWall XP Series Installation/Operation Manual 45 
PREL
IMINARY
Input PositionUse the controls in the Input Position Menu to fine-tune the aspect ratio and image 
position for the current source.
Left/Right: Select Left/Right from the Input Position menu to shift the projected image 
horizontally. Press 
 to shift the image to the right; press  to shift it to the left.
Up/Down: Select Up/Down from the Input Position menu to shift the projected image 
vertically. Press 
 to shift the image...

Page 62

Operation
46 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Figure 4-6. Overscan Modes
Phase (RGB, Component or SCART sources): This control adjusts the phase of the 
pixel sampling clock relative to the incoming signal. Adjust the phase when an RGB, 
Component or SCART image still shows shimmer or “noise” after 
Tracking has been 
optimized.
For best results, use a good test pattern such as a smooth gray consisting of a clear 
pattern of black and white pixels, or a similar “half on,...

Page 63

Operation
PlasmaWall XP Series Installation/Operation Manual 47 
PREL
IMINARY
Memory Presets For each input, the PlasmaWall lets you save image quality settings as presets that you 
can recall at a later time. You can create up to four presets per input and display mode 
(resolution and frame rate). 
The DHD Controller stores the following display modes in each memory preset:
 480i
 480p
 576i
 576p
 720p/24 Hz
 720p/25 Hz
 720p/30 Hz
 720p/50 Hz
 720p/60 Hz
 1080i/50 Hz
 1080i/50 Hz...

Page 64

Operation
48 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
To reset the Custom 1 or Custom 2/THX memory preset to its factory-default state, select 
it, press 
 or  to highlight Reset and press ENTER.
InformationSignal / System: Select Information from the Main Menu, then choose either Signal or 
System to display information about the current input signal (resolution, frequency, type et 
cetera) and installed firmware versions, as well as other information that uniquely identifies...

Page 65

Operation
PlasmaWall XP Series Installation/Operation Manual 49 
PREL
IMINARY
CalibrationUse the Calibration menu to perform advanced picture quality adjustments. This menu 
should be used by ISF-certified technicians only.  
To recall the ISF Night or ISF Day settings, select “ISF Night” or “ISF Day” from the 
Memory Presets menu (see page 47) or use the corresponding remote control buttons. 
Display Color: Use the Display Color settings to adjust the color balance at the DHD 
Controller output. These...

Page 66

Operation
50 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Color Temp: Select Color Temp from the Display Color menu to adjust the color 
temperature. Color temperature establishes the “color of gray” by adjusting the 75% 
white point to various color points. 
What are “color points?”  A “color point” is an x/y coordinate pair that defines a 
color’s location on the standard CIE chromaticity graph, shown in 
Figure 4-7. (CIE 
stands for “Commission Internationale de l’Éclairage”...

Page 67

Operation
PlasmaWall XP Series Installation/Operation Manual 51 
PREL
IMINARY
Black Level: Select Black Level from the Display Color menu to adjust the black level 
“floor” (lower limit). If blacks appear too gray, set Black Level to a higher value.
Input Level: Select Input Level from the Display Color menu to adjust the overall, 
apparent brightness of the displayed image. Its effect is similar to a backlight control on 
an LCD. If parts of the image are extremely bright and hard to see, lower the...

Page 68

Operation
52 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Copy/Paste: You can copy and paste settings from one memory location to another. 
This gives you a convenient starting point for creating a new preset based on an existing 
one, to make the calibration process less time-consuming. 
For example, you can use the Copy/Paste feature to:
 Apply settings from HDMI 1 to HDMI 2, or from HD1 to HD2.
 Calibrate an input for 720p source signals, then use those settings for 1080i...

Page 69

Operation
PlasmaWall XP Series Installation/Operation Manual 53 
PREL
IMINARY
OSD Position: To adjust the position of the OSD, select OSD Position from the 
Calibration menu and press ENTER. 
Press  or  to select “Hor.” or “Ver.” Then, press  or  to change the position. 
ServiceUse the Service menu to access advanced display configuration settings. This menu 
should be used by ISF-certified technicians only.
Test Video: Select Test Video from the Service Menu to access the internal test patterns 
on the...

Page 70

Operation
54 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Remote Control: Select Remote Control from the Service menu to change the following 
settings related to remote control operation.
Remote Code: Select Remote Code from the Remote Control menu to set the 
infrared (IR) code set to which the PlasmaWall will respond. By default, it is set to 17. 
You can change this setting if either:
 Another device in the theater (a DVD player, for example) is responding to 
commands from the...
Start reading Runco XP-50DHD Plasma Display User Manual

Related Manuals for Runco XP-50DHD Plasma Display User Manual

All Runco manuals