Runco XP-50DHD Plasma Display User Manual

Installation
PlasmaWall XP Series Installation/Operation Manual 25 
PREL
IMINARY
Component Video Source Connections: Connect your component video sources to 
the HD1, HD2 and/or Component/SCART inputs as shown in 
Figure 3-7. 
Figure 3-7. Component Video Source Connections
Y PBPR COMPONEN T
VIDEO OUT 
BD/DVD
DTV-Set-Top Box
(DTV-STB) 
RCA-to-BNC
adapter 

Installation
26 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
RGBHV Source Connections: Connect personal computers and/or other RGB sources 
to the HD1, HD2 and/or Component/SCART inputs as shown in 
Figure 3-8. 
Figure 3-8. RGBHV Source Connections
or
ComputerRGB Camcorder
BNC-to-RCA
adapter
Green
Blue
Red
H-Sync
V-Sync
Green
H-Sync
Blue
V-Sync
Red 

Installation
PlasmaWall XP Series Installation/Operation Manual 27 
PREL
IMINARY
SCART RGBS Source Connections: Connect the green, blue and red outputs from 
your SCART source to the Component/SCART input on the DHD Controller. Connect the 
sync output from your SCART source to the Video input on the DHD Controller. See 
Figure 3-9. 
Figure 3-9. SCART RGBS Source Connections
Gaming ConsoleVCR
DVD/DTV STB
SCART-to-RGBS
adapter
Green
Blue
Red
Sync
Green
Blue
Red
Sync 

Installation
28 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Composite and S-Video Source Connections: See Figure 3-10. 
Figure 3-10. S-Video and Composite Video Source Connections
Gaming ConsoleVCR
Camcorder
Composite
S-Video
S-Video
Composite
S-Video
S-Video 

Installation
PlasmaWall XP Series Installation/Operation Manual 29 
PREL
IMINARY
RS-232 Controller 
Connection
Use a straight-through, 9-pin RS-232 cable to connect a PC or control/automation 
system (if present) to the RS-232 port on the DHD Controller; see 
Figure 3-11. 
For more information about using this connection, refer to External Control on page 63. 
Figure 3-11. RS-232 Control System Connection
12345
7896
to Automation/
Control System
or PC2 Receive Data
3 Transmit Data
5 Ground
(none of the...

Installation
30 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Connecting 12-volt 
Trigger Outputs to 
External Equipment 
If your installation includes equipment that responds to 12-volt triggers, connect it to the 
12-volt trigger outputs as shown in 
Figure 3-12. 
Figure 3-12. Connecting 12-volt Trigger Outputs
➤
Tip = +12V Sleeve = Ground
To  12-volt
trigger-activated
device 

Installation
PlasmaWall XP Series Installation/Operation Manual 31 
PREL
IMINARY
Connecting an External IR 
Receiver to the DHD 
Controller
If infrared signals from the remote control cannot reach the DHD Controller due to 
excessive distance or obstructions such as walls or cabinet doors, you can connect an 
external IR receiver to the DHD Controller to extend the range of the remote control. See 
Figure 3-13. 
Figure 3-13. External IR Receiver Connection
CUST1CUST
2SVC HDMI
1HDMI
2EXITRETURN
16 : 9
4 :...

Installation
32 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Connecting AC PowerPlug the female end of the power cord into the AC receptacle on the rear of the 
PlasmaWall. Connect the other end to your AC power source. (The XP-103DHD requires 
200-240
 VAC.)  
Figure 3-14. AC Power Connection
Similarly connect the DHD Controller to a nearby AC outlet.
➤
XP-50DHD / XP-OPAL50DHD
XP-65DHD / XP-OPAL65DHD
XP-103DHD (NOTE: The XP-103DHD requires 200 - 240 VAC) 

PlasmaWall XP Series Installation/Operation Manual 33 
PREL
IMINARY
4.1 
Turning on the Power
1. Turn on your source components.
2. Press the main power switch on the PlasmaWall (see Figure 2-1, Figure 2-2 or Figure 
2-3). Its standby/on indicator lights red.
3. Set the main power switch at the rear of the DHD Controller (see Figure 2-6) to the “on” 
position. Its standby/on indicator lights amber.
4. Press the ON button on the remote control (or 
the ON/STANDBY (
) button on DHD 
Controller front panel)...

Operation
34 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
2. Double click on the Display icon.
3. Click the Settings tab on the display dialog 
box.
4. Set the Screen area to 1024x768 pixels.  
 
 
 
 
 
 
 
 
 
 
5. Click the Advanced button and click the 
Monitor tab on the dialog box. Set the 
Refresh Frequency to 60Hz and click 
OK.
 
 
 
 
 
 
 
 
 
 
 
 
1. The native resolution of the PlasmaWall is 1920 x 1080. Other 
horizontal or vertical resolutions may be scaled upward or...