Runco XP-50DHD Plasma Display User Manual

							XP-50DHD
XP-OPAL50DHD
XP-65DHD
XP-OPAL65DHD
XP-103DHD
High Definition, 1080p Flat Panel Plasma Display
with
and
Digital High Definition
TM Controller/Scaler/Processor
with Vivix IIITM Technology
TM
INSTALLATION/OPERATION MANUAL 
						

							PlasmaWall XP Series Installation/Operation Manual iii 
PREL
IMINARY
RuncoCare™ Standard Two Year Limited 
Warranty
Congratulations on your purchase of a Runco® product! With proper installation, setup and care, you should enjoy many years 
of unparalleled video performance. 
This RuncoCare Standard Limited Warranty is provided free of charge by Runco International with the purchase of a covered 
Runco product. The following sets forth Runco’s Standard Limited Warranty applicable to all Runco projectors, processors, 
LCD and plasma display products, with the exception of the following models: XP-103DHD, SC-1, SC-1a and VW-100HD1.
The following terms and conditions of the RuncoCare Standard Limited Warranty represent a contract between us, Runco 
International and you, the customer who has purchased a Runco product. This contract applies to purchases of covered 
Runco products occurring on or after September 1, 2008. Runco reserves the right to change the terms of this contract, and 
such changes shall apply to purchases of covered Runco products that occur on or after any future effective date.
 Two-year protection from defects in material and workmanship 
 Access to 24x7 phone support 
 Complimentary, second-day one-way shipping 
Runco warrants its products to be free from defects in material and workmanship during the warranty period provided below. 
If, in Runco’s determination, a product proves to be defective in material or workmanship during the warranty period, Runco 
will repair the product, replace the product with a similar new or like new product, or refund a prorata share of the purchase 
price (calculated based on the remainder of the warranty period and the then-current MSRP2 of a similar product), if repair or 
replacement of the product is determined by Runco to not be feasible. 
Runco products are warranted for two (2) years from the date of shipment from Runco. Lamps are warranted six (6) months 
from the date of shipment or 1000 hours, whichever comes first. All other accessories, which includes, but is not limited to, 
cables, remotes, carrying cases, lens cap and other peripherals sold with the Runco product, are warranted for ninety (90) 
days from the date of shipment. Repaired product or replacement lamp is subsequently warranted for the remaining portion (if 
any) of the original warranty term or 90 days from the date the product was shipped to you, whichever is longer. 
This RuncoCare Standard Limited Warranty is valid only for the first customer who purchases the covered product from an 
authorized Runco dealer or distributor. This warranty is not transferable. You may be required to provide proof of purchase in 
order to receive warranty services. 
1. Runco may update this list of products excluded from this warranty from time to time at Runco’s sole discretion, but updates to 
the list of covered products will not apply on a retroactive basis.
RuncoCare Standard Features
Warranty Coverage
2. MSRP is defined as the most recent product price listed on Runco’s price list.
Length of Warranty
Eligibility 
						

							iv PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
In the event of a product defect, please follow the warranty claim procedure provided below: 
1.The Customer is required to contact a Runco dealer or Runco Technical Support via E-mail at [email protected] or via 
phone at (toll free) 800-23RUNCO (800-237-8626). If the customer is located outside North America, call +3589 4200 554 
in Europe for product service. 
2.Be prepared to provide the date of purchase, the place of purchase, serial number, product model number, description of 
the problem and troubleshooting steps already attempted. 
3. Runco Technical Support staff will attempt to correct any minor issues that may be causing the problem. If Runco is 
unable to fix the problem to the customer’s satisfaction, Runco will issue a Return Material Authorization (RMA) if it is 
determined that the claim was made within the coverage period of the Standard Limited Warranty. 
4. The customer will need to return the defective product to the Runco repair depot location specified by the Runco technical 
support representative. The customer will need to properly package the defective product, consisting of the product only, 
and not include any accessories (e.g., cables, remotes, carrying cases, lens, lens cap and other peripherals) and return it 
to the Runco repair depot specified by the technical support representative. It is the customer’s responsibility to properly 
package the hardware, include all appropriate materials, and return it to the location specified by the Runco technical 
support department. The customer will need to address and resolve any shipping damage claims directly with the shipping 
company. 
5. The customer is responsible for providing a suitable box to ship the defective product to an authorized Runco repair depot. 
Boxes may be purchased from a Runco technical support representative. 
6. The customer is responsible for paying freight charges to ship the defective product to an authorized Runco repair depot. 
7. Runco will pay freight charges to return the repaired/replacement product to the customer from the Runco repair depot. 
8. Once an RMA has been created, the customer may contact [email protected] for follow-up questions or 
confirmation status of the claim process. 
This RuncoCare Standard Limited Warranty does not include or is limited by the following: 
1. Products not purchased from an authorized Runco dealer 
2. Rental costs incurred by the customer in the event of product defect or failure 
3. Any product with a defaced, modified, or removed serial number 
4. Damage, deterioration, or malfunction resulting from: 
a Accident, abuse, misuse, neglect, improper ventilation, fire, water, disaster, lightning, or other acts of nature, smoke 
exposure (cigarette or otherwise), unauthorized product modification (including use of an unauthorized mount), or failure 
to follow instructions supplied with the product 
b Repair or attempted repair by anyone not authorized by Runco 
c Any damage to the product due to shipment 
d Removal or installation of the product 
e Causes external to the product, such as electric power fluctuations or failure 
f Use of supplies or parts not meeting Runco’s specifications 
g Normal wear and tear 
h Expected lamp degradation and normal decrease in lamp output over a period of time or as the lamp is consumed 
i Customer caused defects, including but not limited to, scratched/defaced/altered plastics 
RuncoCare Claim Procedure
Warranty Exclusions 
						

							PlasmaWall XP Series Installation/Operation Manual v 
PREL
IMINARY
j Failure to follow maintenance procedures as outlined in the product’s user guide where a schedule is specified for 
regular cleaning of the product 
k Opening the product and/or tampering with internal circuitry 
l Products lost, stolen or discarded 
m Any damage or dissatisfaction associated with latent images, “burnin,” or any other damage determined by Runco to be 
the result of customer use patterns 
n Any other cause, which does not relate to a product defect in material or workmanship 
5. Removal, installation, and setup service charges are excluded from this Standard Limited warranty 
6. Runco’s warranty does not cover black uniformity issues or other LCD issues associated with usage outside the Runco 
recommended guidelines and specifications for the product 
7. Second day shipment delivery time and availability may vary based on origin and destination and Runco is unable to deliver 
to PO Box and FPO Box addresses 
Runco offers extended and expanded service plans. For information on additional product protection, please E-mail 
[email protected] or call (toll free) 800-23RUNCO (800-237-8626). 
Please visit http://www.runco.com/info.html to register product. 
RUNCO PROVIDES NO WARRANTIES, EXPRESS OR IMPLIED, EXCEPT THOSE EXPRESSLY PROVIDED HEREIN. RUNCO 
EXPRESSLY DISCLAIMS ALL OTHER WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND 
FITNESS FOR A PARTICULAR PURPOSE. 
Extended Service Options
Online Product Registration
Limitation of Implied Warranties 
						

							vi PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
RUNCO’S MAXIMUM AGGREGATE LIABILITY HEREUNDER IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF 
THE PRODUCT. 
1. RUNCO SHALL NOT BE LIABLE FOR DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECT IN THE PRODUCT, 
DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF PROFITS, 
LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH BUSINESS RELATIONSHIPS, OR 
OTHER COMMERCIAL LOSS, EVEN IF THE CUSTOMER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 
2. RUNCO SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE 
DAMAGES ANY OTHER DAMAGES, WHETHER INCIDENTAL, INDIRECT, CONSEQUENTIAL OR OTHERWISE. 
3. RUNCO SHALL NOT BE LIABLE FOR ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY. 
This warranty gives you specific legal rights, and you may have other rights, which vary from locality to locality. Some localities 
do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the 
above limitations and exclusions may not apply to you. 
© Copyright 2009 Runco International, LLC (“Runco”). This document contains proprietary information protected by copyright, 
trademark and other intellectual property laws. All rights are reserved. No part of this manual may be reproduced by any 
mechanical, electronic or other means, in any form, without prior written permission of Runco.
The trademarks reproduced in this Runco Owner’s Manual and used on the Runco Products are either owned by Runco or are 
licensed by Runco. You may not reproduce or use the trademarks without the prior written consent of Runco. 
THX and the THX logo are trademarks of THX Ltd. which may be registered in some jurisdictions. All rights reserved.
Runco Products are manufactured under one or more of the following patents: US. Patent 6755540 and Other Patents 
Pending.
Exclusion of Damages
Effect of Local Law
COPYRIGHT AND TRADEMARKS:  
						

							PlasmaWall XP Series Installation/Operation Manual vii 
PREL
IMINARY
Thank you for your purchase of this quality Runco product! For best performance, please read this manual carefully as it is your 
guide through the menus and operation.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that 
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider 
than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is 
provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for the replacement of 
the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point 
where they exit from the apparatus. 
11. Only use the attachments/accessories specified by Runco.
12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer or sold with the apparatus. 
When a cart is used, use caution when moving the cart/apparatus to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in 
any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, 
the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Important Safety Instructions
WARNING 
This symbol is intended to alert the user to the presence of 
uninsulated “dangerous voltage” within the product’s enclosure 
that may be of sufficient magnitude to constitute a risk of electric 
shock.
 
 
This symbol is intended to alert the user to the presence of 
important operating and maintenance (servicing) instructions in the 
literature accompanying the appliance. 
CAUTIONRISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK 
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE. 
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL. 
						

							viii PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Manufacturer’s Name: Runco International, LLC
Manufacturer’s Address: 1195 NW Compton Drive, Beaverton, OR 97006-1992
  hereby declares that the products Model Numbers:
XP-50DHD, XP-OPAL50DHD, XP-65DHD, XP-OPAL65DHD and XP-103DHD 
conform with the provisions of:
Council Directive 2004/108/EC on Electromagnetic Compatibility;
EN 55022 “Limits and methods of measurements of radio interference characteristics of information technology equipment” 
1998;
EN 55024 “Limits and methods of measurements of immunity characteristics of information technology equipment” 1998;
Including:
 EN 61000-4-2 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 2: 
Electrostatic discharge immunity test”
 EN 61000-4-3 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 3: Radiated, 
Radio-Frequency, Electromagnetic Field Immunity Test” 
 EN 61000-4-4 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 4: Electrical 
fast transient/burst immunity test”
 EN 61000-4-5 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 5: Surge 
immunity test”
 EN 61000-4-6 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 6: Conducted 
disturbances induced by radio-frequency fields immunity test”
 EN 61000-4-8 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 8: Conducted 
disturbances induced by power frequency magnetic fields immunity test”
 EN 61000-4-11 “Electromagnetic compatibility (EMC) Part 4: Testing and measurement techniques Section 11: Voltage 
dips, short interruptions and voltage variations immunity tests”
And:
 EN 61000-3-2 “Electromagnetic compatibility (EMC) Part 3, Section 2: Limits for harmonic current emissions (equipment 
input current up to and including 16 A per phase)” 2000;
 EN 61000-3-3 “Electromagnetic compatibility (EMC) Part 3, Section 3: Limitations of voltage changes, voltage 
fluctuations and flicker in public low-voltage supply systems, for equipment with rated current up to and including 16 A 
and not subject to conditional connection” 1995;
Council Directive 2006/95/EC and amended by M1 and C1 on Low Voltage Equipment Safety;
EN 60950 “Safety of information technology equipment, including electrical business equipment”
The Technical Construction file required by this Directive is maintained at the corporate headquarters of Planar Systems, Inc., 
1195 NW Compton Drive, Beaverton, OR 97006.
Date of Declaration: September 2009
Compliance Information
DECLARATION OF CONFORMITY:  
						

							PlasmaWall XP Series Installation/Operation Manual ix 
PREL
IMINARY
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of 
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation. 
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the 
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not 
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be 
hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal Laws. 
For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. 
For lamp specific disposal information check WWW.LAMPRECYCLE.ORG. 
This symbol found on your product or on its packaging, indicates that this product should not be treated as 
household waste when you wish to dispose of it. Instead, it should be handed over to an applicable collection 
point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, 
you will help prevent potential negative consequences to the environment and human health, which could 
otherwise be caused by inappropriate disposal of this product. The recycling of materials will help to conserve 
natural resources. This symbol is only valid in the European Union. If you wish to discard this product, please 
contact your local authorities or dealer and ask for the correct method of disposal.
FCC PART 15: 
INDUSTRY CANADA (ICES-003): 
IMPORTANT RECYCLE INSTRUCTIONS
DISPOSAL OF OLD ELECTRICAL AND ELECTRONIC EQUIPMENT (Applicable throughout the European 
Union and other European countries with separate collection programs) 
						

							x PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Notes: