Runco XP-50DHD Plasma Display User Manual

							PlasmaWall XP Series Installation/Operation Manual 5 
PREL
IMINARY
2.1 
PlasmaWall at a 
Glance
Controls and IndicatorsFigure 2-1, Figure 2-2 and Figure 2-3 show the PlasmaWall front-panel controls and 
indicators. 
Figure 2-1. PlasmaWall XP-50DHD and XP-OPAL50DHD Front-Panel Controls 
and Indicators
Figure 2-2. PlasmaWall XP-65DHD and XP-OPAL65DHD Front-Panel Controls 
and Indicators
2. Controls and Functions
1
3
2(behind
front bezel)4
1
2
34
(behind
front bezel) 
						

							Controls and Functions
6 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
Figure 2-3. PlasmaWall XP-103DHD Front-Panel Controls and Indicators
1.DISPLAY STAND  
Optional accessory for table-top installations.
2.POWER BUTTON 
Connects or disconnects the display panel from the AC power source. 
3.STANDBY/ON INDICATOR  
- Lights green to indicate normal operation;  
- Lights red to indicate that the PlasmaWall is in standby mode. 
4.REMOTE CONTROL SENSOR  
Receives the signals from the remote control.
1
3
2
4 
						

							Controls and Functions
PlasmaWall XP Series Installation/Operation Manual 7 
PREL
IMINARY
ConnectorsFigure 2-4 shows the rear-panel connector locations on the PlasmaWall. 
Figure 2-4. PlasmaWall Rear Panel
SERIAL PC    IN
AUDIO
SLOT1 SLOT3
PR/CR/R PB/CB/BY/GAUDIORLCOMPONENT/RGB INSLOT2AV INAB
XP-50DHD / 
XP-OPAL50DHD
12345
6
XP-65DHD / 
XP-OPAL65DHD
XP-103DHD6
6 
						

							Controls and Functions
8 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
1.SLOT 1  
Not used.
2.SLOT 2 (Dual HDMI input)  
Two, HDCP-compliant digital video inputs. Connect the HDMI output from the 
DHD Controller to input “A” in this slot.
3.SLOT 3 (COMPONENT/RGB input) 
Not used.
4.PC IN  
Not used.
5.RS-232C (9-pin, male D-Sub)  
Connect the Display Control (RS-232 OUT) port on the DHD Controller to this input. 
6.POWER INPUT 
Connect the PlasmaWall to AC power here. 
2.2 
DHD Controller Front 
Panel
Figure 2-5 shows the controls and indicators on the DHD Controller front panel; the 
paragraphs that follow describe them. 
Figure 2-5. DHD Controller Front Panel
1.RUNCO ICON 
Lights blue to indicate that the controller is on or powering up. 
2.IR SENSOR 
Receives IR commands from the remote control. 
3.VACUUM FLUORESCENT DISPLAY 
Can be used instead of the On-Screen Display (OSD). Displays currently-selected 
menu or – if no menu is selected – the connected display device model, current 
source, input resolution and aspect ratio. 
4.ON/STANDBY BUTTON 
Press once to toggle from standby mode to on mode. Press it again to return to 
standby mode. For a discrete on or off command, you can use the direct access 
buttons on the remote control. 
ratio
ratio
input
standby
m
e
n
uinput
enter
3
 HDMI 1
16:9 1080i/60
31
91011
654872
XP-50DHD 
						

							Controls and Functions
PlasmaWall XP Series Installation/Operation Manual 9 
PREL
IMINARY
5.LEFT BUTTON 
Used to direct-select inputs or move the menu cursor left in the OSD. When no menu 
is present on-screen, the LEFT button toggles through the different sources, in this 
order: 
 
HDMI 2 - HDMI 1 - SCART - HD 2 - HD 1 - Component - S-Video 2 - S-Video 1 - 
Composite
 Video
6.DOWN BUTTON 
Use to direct-select aspect ratios or move the menu cursor down in the OSD. When 
no menu is present on-screen, this button toggles through the different aspect ratios, 
in this order: 
 
16:9 - 4:3 - Letterbox - VirtualWide - Cinema - Virtual Cinema - Native
7.RIGHT BUTTON 
Used to direct-select inputs or move the menu cursor right in the OSD. When no 
menus are present on-screen, the RIGHT button toggles through the different 
sources, in this order: 
 
Composite Video - S-Video 1 - S-Video 2 - Component - HD 1 - HD 2 - SCART - 
HDMI
 1 - HDMI 2
8.MENU BUTTON  
Press the MENU button to bring up the main menu, or to exit the current menu and 
return to the previous one. 
9.UP BUTTON 
Use to direct-select aspect ratios or move the menu cursor up in the OSD. When no 
menus are present on-screen, the UP button toggles through aspect ratios in the 
following order: 
 
Native - Virtual Cinema - Cinema - VirtualWide - Letterbox - 4:3 - 16:9
10.ENTER BUTTON 
When an item is highlighted on the OSD, the ENTER button selects the item.
11.STANDBY LED 
Lights amber when the DHD Controller is in standby mode; otherwise it is off. 
						

							Controls and Functions
10 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
2.3 
DHD Controller Rear 
Panel
Figure 2-6 shows the rear connector panel on the DHD Controller.
Figure 2-6. DHD Controller Rear Panel
Outputs1.HDMI Out 
Connect this to the SLOT 2/INPUT A connector on the PlasmaWall (see Figure 2-4). 
2.Display Control 
Connect this to the SERIAL input on the PlasmaWall, using the provided 
communication cable and adapter. 
3.TRIGGERS  
Connection for up to three (3), 12-volt trigger-controlled devices. Output current is 
limited to 250 milliamperes (mA). 
156414
2
31011
789
1213
➤ 
						

							Controls and Functions
PlasmaWall XP Series Installation/Operation Manual 11 
PREL
IMINARY
Inputs4.USB 
A standard, USB Series “B” connection to a personal computer. (For future use.)
5.HDMI 1 / HDMI 2 (Digital) 
HDCP-compliant digital video inputs for connecting an HDMI or DVI source.
6.HD1 / HD2 (5 x Analog BNCs) 
Two inputs (five BNCs per input) for connecting standard-definition (SD = 480i/576i), 
enhanced-definition (ED = 480p/576p) or high-definition (HD = 720p/1080i/1080p) 
component video sources, or RGBHV sources such as personal computers. 
7.Component / SCART (5 x RCA connectors) 
SD/HD input for connecting SDTV, EDTV or HDTV component video sources, or 
RGBHV sources. Also provides RGB input for SCART RGBS sources. 
8.Video 
Standard, composite video input for connecting a VCR, camcorder or other 
composite video source. Also provides composite sync input for SCART RGBS 
sources. 
9.S-Video 1 / S-Video 2 
Two, standard S-Video inputs for connecting a DVD player, satellite receiver or Super 
VHS (S-VHS) VCR. 
10.IR 
Wired input from a Niles- or Xantech-compatible, infrared (IR) repeater system. It is a 
3.5-mm, mini phono jack, wired as follows:
 
Ring = No connection 
Tip = IR Input 
Sleeve = Ground 
11.RS-232 / RS-485 
A female, 9-pin D-sub connector for interfacing with a PC or automation/control 
system. (Currently, only RS-232 interface is supported.) 
12.MAIN AC FUSE 
This is the main AC input fuse (5mm x 20mm, 500 mA, 250V slow-blow). 
13.MAIN POWER SWITCH 
Disconnects or applies power to the DHD Controller.
14.POWER INPUT (100 to 240 VAC) 
Connect the DHD Controller to power here.  
						

							Controls and Functions
12 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
2.4 
PlasmaWall Remote 
Control Unit 
Figure 2-7 shows the PlasmaWall remote control, and the paragraphs that follow describe 
its functionality.
Figure 2-7. DHD Controller/PlasmaWall Remote Control
CUST1THXSVC HDMI
1HDMI
2
EXIT
RETURN
16 : 9
4 : 3
(not available on
some models)
1312
3
7
5
9
10 1211
146
8 4
(“CUST 2” on
some models) 
						

							Controls and Functions
PlasmaWall XP Series Installation/Operation Manual 13 
PREL
IMINARY
1.IR OUTPUT INDICATOR 
Lights when a button is pressed to indicate that an IR signal is being transmitted.
2.ON / OFF 
Press to turn the display on or off.
3.ENTER 
Press to select a highlighted menu item or confirm a changed setting.
4.Cursor Buttons (, , , )  
Use these buttons to select items or settings, adjust settings or switch display 
patterns.
 
 
When no menu is present on-screen, the UP and DOWN buttons toggle through the 
available aspect ratios, in this order: 
 
UP Button = Native - Virtual Cinema - Cinema - VirtualWide - Letterbox - 4:3 - 16:9 
DOWN Button = 16:9 - 4:3 - Letterbox - VirtualWide - Cinema - Virtual Cinema - 
Native
 
 
Likewise, the LEFT and RIGHT buttons toggle through the different source inputs, in 
this order: 
 
LEFT Button = HDMI 2 - HDMI 1 - SCART - HD 2 - HD 1 - Component - S-Video 2 - 
S-Video 1 - Composite
 Video 
RIGHT Button = Composite Video - S-Video 1 - S-Video 2 - Component - HD 1 - 
HD
 2 - SCART - HDMI 1 - HDMI 2
5.RETURN / EXIT 
Press this button to exit the current menu and return to the previous one.  
6.LIGHT  
Press to illuminate the buttons.
7.MENU 
Press this button to access the OSD controls, or to exit the current menu and return 
to the previous one. 
8.VIDEO (1) 
Press to select Composite video input as the source or to enter the numeric 
character
 “1.”
9.COMP (Component) (2)  
Press to select Component/SCART video input as the source or to enter the numeric 
character “2.”
Not all remote control units have this button. If yours does not, use 
the MENU button (see below) to exit the current menu. Note 
						

							Controls and Functions
14 PlasmaWall XP Series Installation/Operation Manual
PREL
IMINARY
10.Aspect Ratio Selection Buttons 
Use the red buttons to select an aspect ratio directly or to enter numeric characters, 
as follows: 
 
 
16:9 (3)  
For viewing 16:9 DVDs or HDTV programs in their native aspect ratio.  
 
4:3 (6)  
Scales the input signal to fit 4:3 display mode in the center of the screen.  
 
LETBOX (Letterbox) (9) 
For viewing LaserDisc movies or non-anamorphic DVDs on a 16:9 screen.  
 
V-WIDE (VirtualWide) 
Enlarges a 4:3 image horizontally in a NON-linear fashion to fit 16:9 full screen display. 
 
CINEMA  
For viewing 2.35:1 source material. The upper and lower portions are masked.  
 
SVC  
Selects the Virtual Cinema aspect ratio.
11.S-VID 1 (4) / S-VID 2 (5) (S-Video) 
Press to select an S-Video input or to enter the numeric character “4” or “5.”
12.HD 1 (7) / HD 2 (8)  
Press to select a HD (RGBHV or YPbPr component) input or to enter the numeric 
character “7” or “8.” 
13.HDMI 1 / HDMI 2 (0)  
Press to select a Digital Video input. Press HDMI 2 to enter the numeric character 
“0.” 
14.Memory Preset Buttons: 
 
ISF NIGHT  
Press to recall settings for the current input from the “ISF Night” memory preset.  
 
ISF DAY 
Press to recall settings for the current input from the “ISF Day” memory preset. 
 
CUST 1 
Press to recall settings for the current input from the “Custom 1” memory preset.  
 
THX (XP-65DHD and XP-OPAL65DHD) / CUST 2 (XP-50DHD, XP-OPAL50DHD 
and XP-103DHD)
 
Press to recall settings for the current input from the “THX” or “Custom 2” memory 
preset.