Runco X 200i Projector User Manual

Installation
Runco X-200i Series Installation/Operation Manual 35 
PREL
IMINARY
Connecting the Active 3D 
Emitter to the Projector
Connect the 3D SYNC IN port on the emitter to the 3D SYNC connector on the 
projector, as shown in 
Figure 3-17. 
Figure 3-17. Active 3D Emitter Connection
Connecting to AC PowerProjector: The X-200i ships with various types of AC power cords. Choose the one that 
is appropriate to your locale. 
Plug the female end of the power cord into the AC receptacle on the rear of the...

Installation
36 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
3.7 
Turning on the Power
1. Turn on your source components. 
2. Set the AutoScope lens motor power switch to the “on” position.
3. Press the ON  button on the remote control (or the POWER button on the 
system keypad) to turn on the X-200i. The blue POWER LED flashes blue to indicate 
that it is warming up. 
4. When the projector is ready for use, the POWER LED turns off. 
5. When the projector is turned on, the Active 3D...

Installation
Runco X-200i Series Installation/Operation Manual 37 
PREL
IMINARY
3.8 
Lens Adjustments
The X-200i gives you a great deal of control over the picture size, position and focus. 
Focus and ZoomTo focus the projected image, grasp the lens 
by the front ring and rotate it. 
To make the picture smaller (zoom out), slide 
the zoom control to the right. 
To make the picture larger (zoom in), slide the 
zoom control to the left. 
To lock the position of the lens, tighten the 
knob with a flat-blade...

Installation
38 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
3.9 
Changing the OSD 
Language
The X-200i can display the OSD menus in English (default), French, German, Italian, 
Spanish, Swedish, Simplified Chinese, Traditional Chinese, Japanese, Korean, 
Portuguese or Russian. 
To change the OSD language:
1. Press MENU on the remote control unit or system keypad to display the Master 
menu. 
2. Press  or  to highlight SYSTEM, then press ENTER (remote control) or SELECT 
(system...

Installation
Runco X-200i Series Installation/Operation Manual 39 
PREL
IMINARY
3.10 
Adjusting the Picture 
Orientation
If the X-200i is ceiling-mounted and/or installed behind the screen, you must change the 
picture orientation to match the installation method. To do this, press MENU on the 
remote control. Then, select SYSTEM from the Master Menu. 
Rear ProjectionIf the projector is used in a rear-projection application (see Figure 3-6), press  repeatedly 
to select Projection Mode from the System...

Installation
40 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Cylindrical Anamorphic 
Lens Installation and 
Adjustment
The Cylindrical Anamorphic lens mount kit consists of everything shown in Figure 3-18. 
Some components shipped with your projector may differ slightly from what is shown in 
these instructions. If any items are missing or damaged, please contact your Runco dealer 
or Runco Customer Service at (800) 23-RUNCO.
Figure 3-18. Cylindrical Anamorphic Lens Mounting Assembly -...

Installation
Runco X-200i Series Installation/Operation Manual 41 
PREL
IMINARY
Attach Lens Mounting Assembly to Lens Motor Carriage Plate: 
1. Remove the two Yaw/X Adjustment Levers and Washers (8) from the bottom of the 
Anamorphic Lens Holder (6).
2. Place the Anamorphic Lens Holder on top of the AutoScope Carriage Plate or Fixed 
CineWide Base Plate (7). Position the bracket so that the long slot at the bottom of 
the lens holder is perpendicular to the corresponding slots on the plate.
3. Secure the...

Installation
42 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Configure Lens Motor Trigger (CineWide with AutoScope): 
CineWide with AutoScope maintains constant image height independent of the aspect 
ratio, while using the full display resolution of the projector. It accomplishes this by moving 
the anamorphic lens in front of the primary lens when widescreen material is being viewed. 
When the viewer transitions back to 16:9 or 4:3 source material, the anamorphic lens 
moves out of...

Installation
Runco X-200i Series Installation/Operation Manual 43 
PREL
IMINARY
Adjusting the Height (Y): With the white field still on-screen, loosen the 
Height/Y
 Adjustment T-Screws on either side of the lens. Then, slowly move the 
anamorphic lens into place so that there are no shadows on the top or bottom of the 
screen: 
When the height is properly set, tighten the Height Adjustment T-Screws to secure the 
lens in place.
Adjusting the Pitch (Angle): Next, angle the lens to even out any...

Installation
44 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Yaw Adjust: Loosen the Yaw/X-Adjustment Levers to allow the lens to pivot freely from 
side to side. Then, angle the lens to even out any left-to-right pincushion distortion: 
Once the proper lens angle has been set, firmly tighten the Yaw/X-Adjustment Levers to 
secure the lens in place. 
Geometry: 
1. Unscrew the Anamorphic Lens just enough to allow it to rotate freely.
2. Grasp the lens by the center ring and rotate the...