Runco X 200i Projector User Manual

Controls and Functions
Runco X-200i Series Installation/Operation Manual 5 
PREL
IMINARY
2.1 
X-200i at a Glance
Figure 2-1 shows the key X-200i functional components. 
Figure 2-1. X-200i Key Functional Components
2. Controls and Functions
Exhaust VentVertical
Lens Shift
Control
Horizontal
Lens Shift
Control
Intake Vent
Exhaust Vent
Focus Ring
Projection Lens
Zoom Control/
Lens Lock
IR Sensor
IR Sensor 

Controls and Functions
6 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
PROJECTION LENS 
Available in three versions: standard throw range (1.85:1 to 2.40:1), short throw range 
(1.56:1 to 1.86:1) and long throw range (2.40:1 to 4.00:1).
IR SENSORS  
Two sensors on the front of the projector receive infrared signals from the remote 
control unit. 
FOCUS RING 
Rotate this to focus the projected image. 
ZOOM CONTROL / LENS LOCK 
Move this from side to side to change the projected image...

Controls and Functions
Runco X-200i Series Installation/Operation Manual 7 
PREL
IMINARY
2.2 
X-200i Rear Panel
Figure 2-2 shows the X-200i rear panel.
Figure 2-2. X-200i Rear View (without Door)
1.LAMP COMPARTMENT COVER 
Remove this cover to access the lamp compartment when replacing the lamp.
2.POWER INPUT (100 to 240 VAC) 
Connect the X-200i to power here. 
3.TRIGGER 1 (3.5-mm, mini phono jack) 
TRIGGER 2 (3.5-mm, mini phono jack) 
Provide 12 (+/- 1.5) volt switched output for screen relays with 250mA...

Controls and Functions
8 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
6.RS-232 
A female, 9-pin D-sub connector for interfacing with a PC or home theater 
automation/control system. 
7.RGB 
Provides a standard, 15-pin VGA-style connection to either an RGB or component 
high-definition source, or to a personal computer. The X-200i automatically detects 
the input signal resolution.
8.USB 
A standard, Type A USB connector for performing firmware upgrades. Can also 
provide power to a 3D...

Controls and Functions
Runco X-200i Series Installation/Operation Manual 9 
PREL
IMINARY
2.3 
Controls and 
Indicators
An eight-button keypad on the projector rear panel provides an alternative to the remote 
control unit for controlling the projector. 
Two LEDs next to the keypad provide visual indications of the current operational state of 
the projector. During normal operation, both of these LEDs are off. 
1.MENU 
Press this button to show or 
hide the OSD controls. 
2.LEFT ()  
Use this button to...

Controls and Functions
10 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
2.4 
X-200i Remote Control1.ON 
Use this button to turn the projector 
on.
2.OFF 
Use this button to turn the projector 
off.
3.Aspect Ratio Selection Buttons 
Press one of these buttons to select 
an aspect ratio: 
 
 
16 : 9: For viewing 16:9 DVDs or 
HDTV programs in their native aspect 
ratio. 
 
4 : 3: Scales the input signal to fit 4:3 
sources in the center of the screen. 
 
LETBOX (Letterbox): For viewing...

Controls and Functions
Runco X-200i Series Installation/Operation Manual 11 
PREL
IMINARY
9.Brightness  
Press to adjust black level. 
10.Memory Preset Buttons: 
 
ISF NIGHT  
Press to recall settings for the current input from the “ISF Night” memory preset. 
 
ISF DAY  
Press to recall settings for the current input from the “ISF Day” memory preset.  
 
CUST 1  
Press to recall settings for the current input from the “Custom 1” memory preset.  
 
CUST 2 
Press to recall settings for the current input...

Controls and Functions
12 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
2.5 
X-200i Active 3D 
Emitter
The Active 3D Emitter, shown below, receives a left/right synchronization signal from the 
projector and transmits it to the Active 3D Glasses worn by the viewers. This signal 
precisely controls when left and right fields are visible through the glasses. 
The Active 3D Emitter has the following 
functional components: 
1.LED Indicators 
Five (5), multi-colored LEDs indicate 
modes of...

Installation
Runco X-200i Series Installation/Operation Manual 13 
PREL
IMINARY
3.1 
Remote Control
To install batteries in the remote control:
1. Slide the battery compartment cover in the direction of the arrow to remove it.
2. Install two AA batteries with the correct polarity.
3. Replace the cover. 
Notes on Batteries Make sure that the battery polarities are correct when installing the batteries.
 Do not mix an old battery with a new one or different types of batteries.
 If you will not use the...

Installation
14 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
 The projector’s front IR receivers have a range of approximately 40 feet (12.19 meters). 
Figure 3-1 shows the reception angles of the IR receivers. 
Figure 3-1. IR Reception Angles