Runco X 200i Projector User Manual

Installation
Runco X-200i Series Installation/Operation Manual 25 
PREL
IMINARY
Install Lens Motor: 
1. Position the AutoScope lens motor as shown in Figure 3-7. 
2. Line up the mounting holes on the lens motor housing with those on the underside of 
the projector.
3. Secure the motor to the projector with the eight (8) supplied M6 x 12mm Pan-Head 
Phillips screws.
Install Ceiling Mount Adapters/Projector Stands: For ceiling installations, the 
adapters bring the attachment points for the projector...

Installation
26 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Installing the Fixed 
CineWide Base Plate 
(Prismatic Anamorphic 
Lens)
To install the fixed CineWide base plate on a X-200i/CineWide with a prismatic 
anamorphic lens:
1. Place the projector upside down on a blanket or other soft surface. 
2. Secure the CineWide base plate and Ceiling Mount Plate (if used) to the projector with 
the three, M4
 x 0.7 x 14mm screws provided with the CineWide lens base plate. See 
Figure 3-9....

Installation
Runco X-200i Series Installation/Operation Manual 27 
PREL
IMINARY
Installing the Fixed 
CineWide Base Plate 
(Cylindrical Anamorphic 
Lens)
To install the fixed CineWide base plate on a X-200i/CineWide with a cylindrical 
anamorphic lens:
1. Place the projector upside down on a blanket or other soft surface.
2. Place the CineWide base plate on the bottom of the projector. 
3.If you are mounting the projector on a ceiling: Line up the three holes on the left 
and right mounting rails...

Installation
28 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
3.5 
Mounting the X-200i
There are several methods for mounting the projector. Depending on your chosen 
installation, one method may be more suitable than another. 
Floor Mounting (Upright)In typical front and rear screen installations, the projector can be mounted to a secure and 
level surface such as a table or cart. Carts are useful when moving a projector during a 
presentation or from site to site. If possible, lock the...

Installation
Runco X-200i Series Installation/Operation Manual 29 
PREL
IMINARY
3.6 
Connections to the 
X-200i
Proceed as follows to connect the X-200i to your video sources, external controller(s) – if 
present – and AC power.
When connecting your equipment:
 Turn off all equipment before making any connections.
 Use the correct signal cables for each source. 
 For best performance and to minimize cable clutter, use high-quality cables that are 
only as long as necessary to connect two devices. (Don’t...

Installation
30 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Connecting Source 
Components to the X-200i
Connect your video sources to the X-200i as shown and described in the sections that 
follow. 
HDMI/DVI Connections: See Figure 3-11. 
Figure 3-11. HDMI/DVI Source Connections
➤
Use the HDMI inputs whenever possible. This ensures the highest 
video quality because the signal is carried in the digital domain 
throughout the entire signal path, from source component output 
into the...

Installation
Runco X-200i Series Installation/Operation Manual 31 
PREL
IMINARY
RGB Connection: Connect your personal computer or other RGB source to the RGB 
input. See 
Figure 3-12. 
Figure 3-12. RGB Connection
SYNC3D SY
RS-232RS-232USBUSB COMPONENT 1COMPONENT 1
12V TRIGGERIII12V TRIGGER
WIRED REMOTEWIRED REMOTE
HDMI 2HDMI 2RGBRGBYYPbPbPrPrHDMI 1HDMI 1COMPONENT 2
POWERPOWERISSUEISSUELED STATUSLED STATUS
SYNC3D SY
RS-232RS-232USBUSB COMPONENT1COMPONENT1
12V TRIGGERIII12V TRIGGER
WIRED REMOTEWIRED...

Installation
32 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Component Video Connections: Connect your component video sources to the 
COMPONENT
 1, COMPONENT 2 or RGB inputs as shown in Figure 3-13. 
 
Figure 3-13. Component Video Connections
3D SYNC3D SYNC
RS-232RS-232USBUSB COMPONENT 1COMPONENT 1
12V TRIGGERIII12V TRIGGER
WIRED REMOTEWIRED REMOTE
HDMI 2HDMI 2RGBRGBYYPbPbPrPrHDMI 1HDMI 1COMPONENT 2COMPONENT 2
POWERSOURCE
SOURCPOWER
ISSUEISSUE
POWERPOWER
LED STATUSLED STATUS
3D SYNC3D...

Installation
Runco X-200i Series Installation/Operation Manual 33 
PREL
IMINARY
RS-232 Controller 
Connection 
Connect a PC or home theater control/automation system (if present) to the RS-232 port 
on the X-200i; see 
Figure 3-14. Use a standard, 9-pin serial cable, wired straight-through.
For more information about using this connection, refer to External Control on page 81.
Figure 3-14. RS-232 Control System Connection
RS-232RS-232USBUSB COMPONENT 1COMPONENT 1
IIIWIRED REMOTE
WIRED REMOTE
POWERSOURCE...

Installation
34 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Connecting an External IR 
Receiver to the Projector
If infrared signals from the remote control cannot reach the projector due to excessive 
distance or obstructions such as walls or cabinet doors, you can connect an external IR 
receiver to extend the range of the remote control. See 
Figure 3-15. 
Figure 3-15. External IR Receiver Connection
Connecting 12-Volt 
Trigger Output to External 
Theater Equipment
If you are...