Runco X 200i Projector User Manual
Have a look at the manual Runco X 200i Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation Runco X-200i Series Installation/Operation Manual 25 PREL IMINARY Install Lens Motor: 1. Position the AutoScope lens motor as shown in Figure 3-7. 2. Line up the mounting holes on the lens motor housing with those on the underside of the projector. 3. Secure the motor to the projector with the eight (8) supplied M6 x 12mm Pan-Head Phillips screws. Install Ceiling Mount Adapters/Projector Stands: For ceiling installations, the adapters bring the attachment points for the projector mounting rails (included with the projector ceiling mount kit) from the bottom of the projector above and behind the AutoScope lens motor housing. For floor installations (where the projector is upright), the adapters allow the projector to lie flat on the mounting surface. Using six (6) each of the supplied, Pan-Head Phillips screws, attach the AutoScope Ceiling Mount Adapters/Projector Stands to the projector as shown in Figure 3-7. Connecting the AutoScope Lens Motor to the Projector: Connect the AutoScope lens transport motor to a 12-volt trigger output on the projector, as shown in Figure 3-8. Figure 3-8. Connecting the AutoScope Lens Transport Motor to the Projector After you have installed the AutoScope lens motor, proceed with Mounting the X-200i (page 28). DO NOT OVER-TIGHTEN THE SCREWS. Caution 3D SYNC3D SYNC RS-232RS-232USBUSB COMPONENT 1COMPONENT 1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI 2HDMI 2RGBRGBYYPbPbPrPrHDMI 1HDMI 1COMPONENT 2COMPONENT 2 3D SYNC3D SYNC RS-232RS-232USBUSBCOMPONENT1COMPONENT1WIRED REMOTEWIRED REMOTE HDMI2HDMI 2RGBRGBYYPbPbPrPrHDMI1HDMI1COMPONENT2COMPONENT2 AuptoScope Lens Transport Motor AC Input +12V Trigger InputPower Switch 3.5-mm mini plug
Installation 26 Runco X-200i Series Installation/Operation Manual PREL IMINARY Installing the Fixed CineWide Base Plate (Prismatic Anamorphic Lens) To install the fixed CineWide base plate on a X-200i/CineWide with a prismatic anamorphic lens: 1. Place the projector upside down on a blanket or other soft surface. 2. Secure the CineWide base plate and Ceiling Mount Plate (if used) to the projector with the three, M4 x 0.7 x 14mm screws provided with the CineWide lens base plate. See Figure 3-9. Figure 3-9. Projector with Whitney (Prismatic) Lens Base Plate - Bottom View ➤ DO NOT OVER-TIGHTEN THE SCREWS. Caution
Installation Runco X-200i Series Installation/Operation Manual 27 PREL IMINARY Installing the Fixed CineWide Base Plate (Cylindrical Anamorphic Lens) To install the fixed CineWide base plate on a X-200i/CineWide with a cylindrical anamorphic lens: 1. Place the projector upside down on a blanket or other soft surface. 2. Place the CineWide base plate on the bottom of the projector. 3.If you are mounting the projector on a ceiling: Line up the three holes on the left and right mounting rails (included with the projector ceiling mount kit) with those on the bottom of the projector and CineWide base plate. 4. Secure the CineWide base plate (and ceiling mounting rails, if needed) to the projector with the Pan-Head Phillips screws provided with the CineWide lens base plate. See Figure 3-10. Figure 3-10. X-200i/CineWide with McKinley (Cylindrical) Lens Base Plate and Ceiling Mounting Rails - Bottom View 1. Do not use the mounting screws provided with the ceiling mounting kit. Use only the hardware provided with the CineWide lens base plate. 2. DO NOT OVER-TIGHTEN THE SCREWS. Caution
Installation 28 Runco X-200i Series Installation/Operation Manual PREL IMINARY 3.5 Mounting the X-200i There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. Floor Mounting (Upright)In typical front and rear screen installations, the projector can be mounted to a secure and level surface such as a table or cart. Carts are useful when moving a projector during a presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it from being moved during a presentation. Ceiling Mounting (Inverted) For fixed installations, and for those that want the projector out of sight or have a limited space for projector and audience, you can invert the X-200i and suspend it from the ceiling using a specially-designed ceiling mount fixture. For detailed installation instructions, refer to the documentation provided with the ceiling mount kit. Adjusting the Projection Angle If the screen is significantly higher or lower than the projector, you can also tilt the projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling mount. For a floor installation, turn the adjustable feet at the bottom of the projector to adjust the projection angle. If you do this, you may need to vertically shift the image to compensate. For detailed instructions, refer to Lens Adjustments on page 37. ➤ ➤ ➤
Installation Runco X-200i Series Installation/Operation Manual 29 PREL IMINARY 3.6 Connections to the X-200i Proceed as follows to connect the X-200i to your video sources, external controller(s) – if present – and AC power. When connecting your equipment: Turn off all equipment before making any connections. Use the correct signal cables for each source. For best performance and to minimize cable clutter, use high-quality cables that are only as long as necessary to connect two devices. (Don’t use a 20-foot cable when a 6-foot cable will suffice.) Route all cables through the opening at the bottom of the projector. Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Connector Panel AccessTo access the connector panel, open the rear door by grasping the handle and pulling it down and toward you. Route cables through this opening
Installation 30 Runco X-200i Series Installation/Operation Manual PREL IMINARY Connecting Source Components to the X-200i Connect your video sources to the X-200i as shown and described in the sections that follow. HDMI/DVI Connections: See Figure 3-11. Figure 3-11. HDMI/DVI Source Connections ➤ Use the HDMI inputs whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the projector. Tip 3D SYNC3D SYNC RS-232RS-232USBUSB COMPONENT 1COMPONENT 1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI 2HDMI 2RGBRGBYYPbPbPrPrHDMI 1HDMI 1COMPONENT 2 POWERSOURCE SOURCPOWER ISSUEISSUE POWERPOWER LED STATUSLED STATUS 3D SYNC3D SYNC RS-232RS-232USBUSBCOMPONENT1COMPONENT1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE RGBRGBYYPbPbPrPrCOMPONENT POWER SOURCESOURC POWERISSUEISSUE POWERPOWER LED STATTTUSAALED STATTTUSAA HDMI AV OUT HDMI source (BD, DVD, DTV Set-Top Box etc.)
Installation Runco X-200i Series Installation/Operation Manual 31 PREL IMINARY RGB Connection: Connect your personal computer or other RGB source to the RGB input. See Figure 3-12. Figure 3-12. RGB Connection SYNC3D SY RS-232RS-232USBUSB COMPONENT 1COMPONENT 1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI 2HDMI 2RGBRGBYYPbPbPrPrHDMI 1HDMI 1COMPONENT 2 POWERPOWERISSUEISSUELED STATUSLED STATUS SYNC3D SY RS-232RS-232USBUSB COMPONENT1COMPONENT1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI 2HDMI 2YYPbPbPrPrHDMI1HDMI 1COMPONENT2 POWERPOWERISSUEISSUELED STATTTUSAALED STATTTUSAA or ComputerRGB Camcorder
Installation 32 Runco X-200i Series Installation/Operation Manual PREL IMINARY Component Video Connections: Connect your component video sources to the COMPONENT 1, COMPONENT 2 or RGB inputs as shown in Figure 3-13. Figure 3-13. Component Video Connections 3D SYNC3D SYNC RS-232RS-232USBUSB COMPONENT 1COMPONENT 1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI 2HDMI 2RGBRGBYYPbPbPrPrHDMI 1HDMI 1COMPONENT 2COMPONENT 2 POWERSOURCE SOURCPOWER ISSUEISSUE POWERPOWER LED STATUSLED STATUS 3D SYNC3D SYNC RS-232RS-232USBUSBCOMPONENT1COMPONENT1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI2HDMI2HDMI1HDMI1 POWER SOURCESOURC POWERISSUEISSUE POWERPOWER LED STATTTUSAALED STATTTUSAA Y PBPR COMPONEN T VIDEO OUT BD/DVD DTV-Set-Top Box (DTV-STB) RCA-to-BNC adapter
Installation Runco X-200i Series Installation/Operation Manual 33 PREL IMINARY RS-232 Controller Connection Connect a PC or home theater control/automation system (if present) to the RS-232 port on the X-200i; see Figure 3-14. Use a standard, 9-pin serial cable, wired straight-through. For more information about using this connection, refer to External Control on page 81. Figure 3-14. RS-232 Control System Connection RS-232RS-232USBUSB COMPONENT 1COMPONENT 1 IIIWIRED REMOTE WIRED REMOTE POWERSOURCE SOURCEPOWER ISSUEISSUE POWERPOWER LED STATUSLED STATUS USBUSB COMPONENT1COMPONENT1 III WIRED REMOTEWIRED REMOTE POWER SOURCESOURCE POWERISSUEISSUE POWERPOWER LED STATTTUSAALED STATTTUSAA 12345 7896 to Automation/ Control System or PC 2 Receive Data(to ctrl. system) 3 Transmit Data(from ctrl. system) 5 Ground(none of the other pins are used)
Installation 34 Runco X-200i Series Installation/Operation Manual PREL IMINARY Connecting an External IR Receiver to the Projector If infrared signals from the remote control cannot reach the projector due to excessive distance or obstructions such as walls or cabinet doors, you can connect an external IR receiver to extend the range of the remote control. See Figure 3-15. Figure 3-15. External IR Receiver Connection Connecting 12-Volt Trigger Output to External Theater Equipment If you are installing an X-200i/CineWide with AutoScope, connect the AutoScope lens motor to a 12-volt trigger output on the X-200i as shown in Figure 3-8. Similarly connect other 12-volt trigger-activated equipment (such as retractable screens or screen masks) to the other trigger output; see Figure 3-16. Figure 3-16. 12-Volt Trigger Output Connection ➤ 3D SYNC3D SYNC RS-232RS-232USBUSB COMPONENT 1COMPONENT 1 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI 2HDMI 2RGBRGBYYPbPbHDMI 1HDMI 1COMPONENT 2COMPONENT 2 POWERPOWERISSUEISSUELED STATUSLED STATUS 3D SYNC3D SYNC RS-232RS-232USBUSBCOMPONENT1COMPONENT1 12V TRIGGERIII12V TRIGGER HDMI2HDMI 2RGBRGBYYPbPbHDMI1HDMI 1COMPONENT2COMPONENT2 POWERPOWERISSUEISSUELED STATTTUSAALED STATTTUSAA (3.5-mm, mini phono plugs) IR Sensor IR RepeaterRemote Control ➤ 3D SYNC3D SYNC RS-232RS-232 12V TRIGGERIII12V TRIGGER WIRED REMOTEWIRED REMOTE HDMI 2HDMI 2HDMI 1HDMI 1 POWERPOWERISSUEISSUELED STATUSLED STATUS 3D SYNC3D SYNC RS-232RS-232WIRED REMOTEWIRED REMOTE HDMI2HDMI2HDMI1HDMI 1 POWERPOWERISSUEISSUELED STATTTUSAALED STATTTUSAATip = +12V Sleeve = Ground 3.5-mm mini plug Retractable Screen or other 12-volt trigger-activated device