Runco X 200i Projector User Manual

Operation
Runco X-200i Series Installation/Operation Manual 65 
PREL
IMINARY
REC709 chooses the REC709 color gamut.
 Select SMPTE-C to choose the SMPTE-C color gamut.
 Select EBU to choose the EBU color gamut.
 Select Native to use REC709 for cyan, magenta, and yellow and uncorrected values 
for red, green, and blue. 
 Select PCE to use the Personal Color Equalizer feature of the X-200i. PCE lets you 
define a custom color gamut. Refer to 
PCE on page 67 for instructions on how to do 
this.
Table 4-2...

Operation
66 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
RGB Adjust: To remove any trace of color from the white areas of the projected image, 
choose 
RGB Adjust from the Advanced Image menu and press ENTER. This displays the 
RGB Adjust sub-menu, shown at right. 
Use the Gain controls to correct color imbalances in the bright areas of the 
image. A good way to do this is to use a test pattern consisting mostly of solid white 
areas, such as an 80 IRE “window” pattern. If the white...

Operation
Runco X-200i Series Installation/Operation Manual 67 
PREL
IMINARY
Sync Level (Component sources only): Select Sync Level to adjust the voltage level 
of the X-200i Sync signal detection circuitry.
Sync Level adjustment is occasionally necessary when a DVD player or HDTV source 
signal drops “below black” (for example, during scenes with explosions or when 
subtitles are present) and causes the projector to temporarily lose sync. If the 
Sync 
Level from the source is persistently too low, the...

Operation
68 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
White Balance: To precisely adjust the white point associated with the custom color 
gamut, choose White Balance from the PCE sub-menu. These controls operate identically 
to the Gain controls in the 
RGB Adjust menu (described on page 66). 
SystemUse the controls in the System menu, shown in Figure 4-10, to change the display 
orientation and perform other, common installation tasks. 
Figure 4-10. X-200i System Menu
Menu...

Operation
Runco X-200i Series Installation/Operation Manual 69 
PREL
IMINARY
Blank Screen: Select Blank Screen from the System menu to choose the color of the 
blank screen that appears when no source signal is present. The options are Black, Blue 
and White. The default is Black.
Auto Power Off: Set Auto Power Off to On to have the X-200i turn itself off after 20 
minutes of inactivity (no source signal present).
Auto Power On: Setting Auto Power On to On causes the projector to automatically 
power up...

Operation
70 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
ControlSelect Control from the Main Menu to set various options related to control of the 
projector. 
Trigger 1: Select Trigger 1 from the Control menu to specify when the Trigger 1 port 
outputs 12 volts. There is a three-second delay before activation to prevent operation 
while selecting an aspect ratio.
AutoScope causes the port to output 12 volts whenever the the Cinema or Virtual 
Cinema aspect ratio is active.
Lamp causes...

Operation
Runco X-200i Series Installation/Operation Manual 71 
PREL
IMINARY
Infrared Remote: Select Infrared Remote from the Control menu to specify the remote 
IR code set to which the X-200i responds. The default is Normal. Choose Code 2 if other 
equipment in the theater responds to commands from the X-200i remote control in ways 
that are unexpected or undesirable. Choose Code
 2 to disable IR communication 
altogether. 
When you select a different remote code set on the X-200i, you must re-program...

Operation
72 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
You can also perform various diagnostic tasks, such as displaying test patterns, from this 
menu. 
System Information: Select System Information from the Service menu to view 
information that uniquely identifies your projector: its Model Name, Serial Number, 
installed Software Version and FPGA Version. 
Should you ever need to contact Runco Technical Support, this information will help them 
answer your questions and/or resolve...

Operation
Runco X-200i Series Installation/Operation Manual 73 
PREL
IMINARY
4.5 
Using the 3D Glasses 
The 3D LCD Shutter Glasses function with the Runco Active3D Emitter and the projector 
to provide unsurpassed 3D stereoscopic viewing. This section describes the features, 
connection, setup and operation of the 3D LCD Shutter Glasses. 
Key Features RF synchronization for uninterrupted 3D performance 
 Supports refresh rates from 50 to 240 Hz for compatibility with both current and future 
3D...

Operation
74 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Charging the BatteryThe glasses must be fully charged before first use and whenever the Battery Status LED 
flashes red once every couple of seconds. The glasses will charge a completely dead 
battery in approximately five hours. You may use the glasses while the battery is being 
charged. 
To charge the 3D Glasses:
1. Attach one end of the supplied charging cable to the Power Input above the left lens 
on the glasses. 
2. Attach...