Runco X 200i Projector User Manual

External Control
Runco X-200i Series Installation/Operation Manual 85 
PREL
IMINARY
Response: ACK:INPUT = 0 [CR]
Input: op phase = 50 [CR]
Response: ERR:NA [CR]
Input: op phase ? [CR]
Response: ERR:NA [CR]
The last three commands show what happens when a control is unavailable.  In this case, 
the source was set to “HDMI
 1” (value = 0) and then the phase slider was attempted to be 
adjusted and queried.  The response was “NA” or not available. 
 
Table 6-2. Serial Commands 
OperationCommandsValuesNotes...

External Control
86 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
resync (execute)
color.space = ?0 = Auto
1 = REC709
2 = REC601
3 = RGB-PC
4 = RGB-Video
gamma = ?0 = 1.8
1 = 2.0
2 = 2.2
3 = 2.35
4 = 2.5
color.temp = ?0 = 5500K
1 = 6500K
2 = 7500K
3 = 9300K
4 = Native
frame.rate = ?0 = Auto
2 = 48 Hz
3 = 50 Hz
4 = 60 Hz
color.gamut = ?0 = Auto
1 = REC709
2 = SMPTE C
3 = EBU
4 = Native
6 = PCE
satco = ?0 = Off
1 = On
red.offset = ?0-200
green.offset = ?0-200
blue.offset = ?0-200
red.gain...

External Control
Runco X-200i Series Installation/Operation Manual 87 
PREL
IMINARY
blank.screen = ?0 = Logo
1 = Black
2 = Blue
3 = White
logo.disp = ?0 = Off
1 = On
auto.poweroff = ?0 = Off
1 = On
auto.poweron = ?0 = Off
1 = On
proj.mode = ?0 = Front Tabletop
1 = Front Ceiling
2 = Rear Tabletop
3 = Rear Ceiling
model.name   ?
ser.number   ?
soft.version   ?
h.refresh   ?kHz
v.refresh   ?Hz
pixel.clock   ?MHz
signal   ?
lamp.hours   ?
total.hours   ?
factory.reset (execute)
pattern =0 = Off
1 = White
2 =...

External Control
88 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
trig1
trig2= ?0 = Lamp
3 = 4:3
4 = AutoScope
5 = RS232
6 = On
7 = Off
adcontrast = ?0 = Off
1 = On
blue.only =0 = Off
1 = On
osd.timer = ?0 = forever
1 = 10 sec.
2 = 30 sec.
3 = 60 sec.
ir.enable = ?0 = Disable
1 = Code 1
2 = Code 2
menu.pos = ?0 = Top left
1 = Top right
2 = Bottom left
3 = Bottom right
4 = Center
trans.menu = ?0 = 0%
1 = 25%
2 = 50%
3 = 75%
environment   ?temperatures
language = ?0 = English
1 = French
2...

External Control
Runco X-200i Series Installation/Operation Manual 89 
PREL
IMINARY
3D.syncdelay = ?100 +/- 40 ms
3D.syncinvert = ?0 = Normal
1 = Inverted
power.chime = ?0 = Off
1 = On
errcode?Refer to RS-232 Error Codes 
on page 91. 
lamp.vol?returns lamp voltage
cinewide = ?0 = Off
1 = CineWide
2 = AutoScope
red.hsg.hue
yellow.hsg.hue
green.hsg.hue
cyan.hsg.hue
blue.hsg.hue
magenta.hsg.hue= ?0-200Personal Color Equalizer (PCE) 
hue settings.
red.hsg.sat
yellow.hsg.sat
green.hsg.sat
cyan.hsg.sat...

External Control
90 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
cal.text1
cal.text2
cal.text3
=Up to 30 characters. The X-200i start-up screen is cus-
tomizable with three lines of text of 
up to 30 characters each. This text 
appears below the “CALIBRATED 
FOR:” text in the logo screen.  The 
allowable characters are all num
-
bers, letters (uppercase and low-
ercase), spaces, and symbols 
available in the ASCII code set.
3d.dlplink = ?0 = Off
1 = On
3d.pattern = ?0 = Off
1 = On
3D...

External Control
Runco X-200i Series Installation/Operation Manual 91 
PREL
IMINARY
RS-232 Error CodesIf an errcode ? command returns one of the following values, you have encountered a 
likely system error requiring the attention of a qualified service technician. Try resetting the 
projector by powering it off, allowing it to cool and powering it on again. Refer to 
Table 6-3 
and contact your dealer if the problem persists. 
The specific code number identifies the source of the error detected, and is...

External Control
92 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
6.2 
Using Discrete IR 
Codes
The X-200i accepts commands in the form of IR signals that conform to the NEC protocol. 
Each X-200i remote control button has an NEC control code associated with it. 
As shown in Table 6-1, there are two complete sets of remote codes (designated “Set 1” 
and “Set 2”).  Through the on-screen menu, the projector can be configured to use either 
set.  The reason for two sets is to allow control...

External Control
Runco X-200i Series Installation/Operation Manual 93 
PREL
IMINARY
6.3 
Using HDMI CEC 
Messages
The X-200i accepts and can respond to CEC command messages from a disc player, 
satellite receiver or DVR/set-top box via an HDMI connection. Using CEC, the X-200i can 
perform the following actions:
 Turn itself on and select the correct input when the source component initiates 
playback of a disc or recorded program. 
 Turn the source component on when you switch to its corresponding input...

External Control
94 Runco X-200i Series Installation/Operation Manual
PREL
IMINARY
Vendor Remote Button 
Down0x8A[Vendor Specific RC 
Code]YesYes
Give Device Vendor ID0x8CNoneYesNo
Menu Request0x8D[Menu Request Type]YesNo
Meun Status0x8E[Menu State]YesNo
Give Device Power Status0x8FNoneYesNo
Report Power Status0x90[Power Status]YesNo
Get Menu Language0x91NoneYesNo
Inactive Source0x9D[Physical Address]YesNo
CEC Version0x9E[CEC Version]YesNo
Get CEC Version0x9FNoneYesNo
Vendor Command With ID0xA0[Vendor...