Runco Cl 810 Ultra Projector User Manual
Here you can view all the pages of manual Runco Cl 810 Ultra Projector User Manual. The Runco manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 61
Runco CL-810 Series Owner’s Operating Manual 49 PREL IMINARY 5.1 Lamp Replacement The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to obtain a replacement lamp. 1. Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. 2. Loosen the two captive screws from the lamp...
Page 62
Maintenance and Troubleshooting 50 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY 5.2 Troubleshooting Tips Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the CL-810. If the suggested solutions fail to resolve the problem or if you encounter an issue not described here, please contact Runco Technical Support. Table 5-1. Troubleshooting Chart SymptomPossible Cause(s)Solution The projector does not turn on. The CL-810 is not plugged in or...
Page 63
Maintenance and Troubleshooting Runco CL-810 Series Owner’s Operating Manual 51 PREL IMINARY TEMP and LAMP LEDs are both flashing red. The lamp cover is open. Fans are not working properly. Close the lamp cover. Please contact your Runco dealer for assistance. LAMP LED lights solid red. The lamp has failed or exceeded its usage life. Replace the lamp with a new one. TEMP LED lights solid red. CL-810 internal temperature is too high. Power off the CL-810 and allow it to cool down....
Page 64
Maintenance and Troubleshooting 52 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Notes:
Page 65
Runco CL-810 Series Owner’s Operating Manual 53 PREL IMINARY 6.1 RS-232 Connection and Port Configuration To interface the CL-810 with a home theater automation/control system or a PC running terminal emulation software: 1. Connect it to your control system or PC as shown in Figure 3-11. 2. Start a terminal session on your PC using a terminal-emulation program, such as HyperTerminal. 3. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow...
Page 66
Serial Communications 54 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY x023xKeypad 3 x024xKeypad 4 x025xKeypad 5 x026xKeypad 6 x027xKeypad 7 x028xKeypad 8 x029xKeypad 9 x030xKeypad 0 x031xStore image settings to Memory 1 x032xStore image settings to ISF Night x033xStore image settings to ISF Day x046xRestore image settings from Memory 1 x047xRestore image settings from ISF Night x048xRestore image settings from ISF Day x049xLoad default of current source x051xSingle source, full-screen...
Page 67
Serial Communications Runco CL-810 Series Owner’s Operating Manual 55 PREL IMINARY x081xImage orientation = floor front x082xImage orientation = ceiling front x083xImage orientation = floor rear x084xImage orientation = ceiling rear x091xLamp Power = 200W x092xLamp Power = 250W x121xOSD Language = English x122xOSD Language = French x123xOSD Language = Spanish x124xOSD Language = German x125xOSD Language = Italian x131xSwitch to Composite input x132xSwitch to S-Video input x133xSwitch to RGB-HD input...
Page 68
Serial Communications 56 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Notes:
Page 69
Runco CL-810 Series Owner’s Operating Manual 57 PREL IMINARY 7.1 CL-810 Specifications Table 7-1 lists the CL-810 specifications. 7Specifications Table 7-1. CL-810 Specifications Projector Type:Digital Light Processing (DLP), Single-Chip SuperOnyx DMD Native Resolution:1280 x 720 (16:9) Aspect Ratios:4:3, Letterbox, 16:9 Anamorphic, VirtualWide, Cinema, Virtual Cinema Video Standards:NTSC, PAL, SECAM DTV Compatibility:480p, 576p, 720p, 1080i Scan Frequency:Horizontal: 15 - 80 kHz Vertical: 50 -...
Page 70
Specifications 58 Runco CL-810 Series Owner’s Operating Manual PRELI MINARY Brightness and Contrast: Cinema Standards Measurement System (CSMS) Specifications - Brightness*: 14.5 to 21.6 foot-Lamberts (fL) - Contrast Ratio*: 200:1 to 220:1 *Variable depending on RVR setting These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100...