Runco Cl 810 Ultra Projector User Manual

Runco CL-810 Series Owner’s Operating Manual 29 
PREL
IMINARY
4.1 
Turning on the Power
1. Turn on your source components. 
2. Turn on the main power switch at the rear of the projector. The POWER LED lights 
orange. The LAMP and TEMP LEDs light red briefly, then go out. 
3. Press the ON button on the remote control to turn on the CL-810. The POWER LED 
flashes orange to indicate that it is warming up. 
4. When the projector is ready for use, the POWER LED lights green. 
5. “Searching...” appears on the...

Operation
30 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
4.4 
Lens Adjustments
The CL-810 gives you a great deal of control over the picture 
size, position and focus. To access the motorized lens 
controls, use the FOCUS, ZOOM and LENS buttons on the 
remote control. 
FocusTo focus the projected image, press the FOCUS button, then use the left- and right-arrow 
buttons to adjust the focus. 
ZoomTo make the picture smaller (zoom out), press the ZOOM button, then use the left-arrow ( 
 )...

Operation
Runco CL-810 Series Owner’s Operating Manual 31 
PREL
IMINARY
4.8 
Selecting An Input 
Source
When you turn on the CL-810, it switches to the 
last selected input and looks for a valid signal. 
Use these buttons on the remote control to select 
an input source directly. 
4.9 
Using 
Picture-In-Picture/
 
Picture-By-Picture 
(PIP/PBP)
For PIP and PBP purposes, there are two groups 
of inputs separated by their display modes: 
• Video (SD) group: Video, S-Video and 
Component
 1 inputs. 
•...

Operation
32 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
Figure 4-1. CL-810 OSD Menu Structure
Option
Reset Image Settings Yes / No
Sleep Timer 0, 10, 20, 30 ... 180 minutes
Lamp Hours (read only)
OSD Timer 0, 3, 6, 9 ... 60 seconds
OSD PositionHorizontal
Vertical
PC & HD Adjust (480p 
and higher-res. signals 
only)Auto
Frequency 0, +1, +2, +3 ... +17
Phase 0, +1, +2, +3 ... +31
H. Position -30, -29 ... 0 ... +29, +30
V. Position -28, -27 ... 0 ... +29, +30
PIP/PBP Set Up  
(not available...

Operation
Runco CL-810 Series Owner’s Operating Manual 33 
PREL
IMINARY
Main MenuThe Main Menu is the starting point for accessing all projector functions. 
(The Set Up and ISF Calibration menus are hidden and not accessible until you enter a 
passcode.)
The active source is indicated by an arrow (>) to its left; in the example at left, Video is the 
active source. To select a different source, use the 
 or  button to highlight it and press 
ENTER or . 
Picture Adjustment Use the controls in the...

Operation
34 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
Although it may be possible to obtain satisfactory picture quality using the naked eye and 
regular program material, Runco recommends using the following calibration tools for best 
results: 
 External test pattern source -- Sencore VP401 Multimedia Video Generator, Ovation 
Multimedia test DVD or equivalent.
 A blue filter (provided with many test DVDs), for color level and tint adjustments.
Connect your test pattern source to the...

Operation
Runco CL-810 Series Owner’s Operating Manual 35 
PREL
IMINARY
Contrast: On your external test pattern source, select a stepped, gray-bar pattern like the 
one shown in 
Figure 4-3. 
Figure 4-3. Typical Gray Bar Pattern for Adjusting Contrast
Select Contrast from the Adjustment menu and press ENTER. Adjust the contrast to a 
point just below which the white rectangle starts to increase in size.
Color Saturation: On your external test pattern source, select a color bar pattern like the 
one shown...

Operation
36 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
Select Color from the Adjustment menu and press ENTER. While looking at the color bar 
pattern through a blue filter, adjust the color saturation level until the outermost (gray and 
blue) color bars appear to be a single shade of blue: 
Tint: Tint or “hue” is essentially the ratio of red to green in the color portion of the image. 
When tint is decreased, the image appears redder; when it is increased the image 
appears greener. To...

Operation
Runco CL-810 Series Owner’s Operating Manual 37 
PREL
IMINARY
Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust 
sharpness, select Sharpness from the Adjustment menu and press ENTER. On your 
external test pattern source, select a pattern like the one shown in 
Figure 4-5. Adjust as 
needed, looking for white edges around the transitions from black to gray and 
differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness 
setting...

Operation
38 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
Color Temperature: The CL-810 has six memory settings for Color Temperature. Four 
of these settings are factory set to default as follows: 
 0 -- Original lamp color temperature 
 1 -- 5400 kelvins 
 2 -- 6500 kelvins 
 3 -- 8500 kelvins 
4 -- Custom 
5 -- Custom 
Custom 4 and 5 memory are installer-adjustable and can be used to create custom 
settings. There are nine adjustable “white balance” parameters available for the...