Runco Cl 810 Ultra Projector User Manual

Operation
Runco CL-810 Series Owner’s Operating Manual 39 
PREL
IMINARY
Table 4-1. Aspect Ratio Settings 
Aspect Ratio
Remote 
Control
Key
Description
AnamorphicANASelect Anamorphic to view 
16:9 DVDs and HDTV 
programs in their native 
aspect ratio. 4:3 images are 
stretched horizontally to fit a 
16:9 screen. 
Standard 4:34X3Standard 4:3 scales the 
input signal to fit in the 
center of the 16:9 screen. 
4:3 is the aspect ratio used 
by computer monitors, 
standard television 
programming and most 
VHS...

Operation
40 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
InstallationTo access the Installation adjustments, press MENU, then press the  or  button to 
highlight Installation and press ENTER. The Installation sub-menu, shown at left, appears. 
Press EXIT to return to the previous menu or press MENU to close all menus. 
Language: Press the  or  button to select from the available languages: English, 
French, Spanish, German and Italian. 
Picture Orientation: Press the  or  button to change...

Operation
Runco CL-810 Series Owner’s Operating Manual 41 
PREL
IMINARY
RS-232 Baud Rate: Press the  or  button to select the projector’s RS-232 Baud 
Rate. This function is used to change the transfer rate of the RS-232 connection. (This 
setting must match the data rate of the device connected to the RS-232 input.) 
Blue Image: Press the  or  button to turn the Blue Image Off or On. This feature 
removes all red and green color information from the image (simulating a blue filter), and is 
useful for...

Operation
42 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
PIP/PBP Set Up: Select PIP/PBP Set Up from the Option menu to change the PIP/PBP 
settings.
• PIP/PBP Enable: Press the  or  button to select PIP/PBP Enable, then press 
ENTER. Press the  or  button to select Off or On, then press ENTER. 
• PIP Set Up: Press the  or  button to select PIP Set Up, then press ENTER. Press 
the  or  button to select PIP Off, Graphic in Video or Video in Graphic, then press 
ENTER. 
• PBP Set Up: Press the...

Operation
Runco CL-810 Series Owner’s Operating Manual 43 
PREL
IMINARY
Gamma Selection: The normal gamma setting of 2.2 is correct for almost all signals and 
conditions. If excess ambient light washes out the image and it becomes difficult or 
impossible to see details in dark areas, lower the gamma setting to compensate. This will 
improve contrast while maintaining good details for blacks. Conversely, if the image is 
washed out and unnatural, with excessive detail in black areas, increase the...

Operation
44 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
Amplitude Adjust: The Amplitude Adjust menu allows you to fine-tune the 
curently-selected image aspect ratio by stretching it horizontally or vertically, in small 
increments. This can be useful if your projector is equipped with an anamorphic lens. 
The Horizontal control adjusts the image width while keeping the height constant. 
Similarly, the Vertical control adjusts the image height while keeping the width constant. 
Horizontal...

Operation
Runco CL-810 Series Owner’s Operating Manual 45 
PREL
IMINARY
The procedure for changing the secondary IR code on the remote only is the same, 
except that you point the remote away from the projector. 
Reset Lamp Timer: When you replace the projector lamp (refer to Lamp Replacement 
on page 49), you should also reset the lamp timer. To do this, select Reset Lamp Timer 
from the Set Up menu. Press the right-arrow key on the remote to highlight “Yes,” then 
press ENTER to confirm the reset. 
Fan...

Operation
46 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
ISF CalibrationTo access the ISF Calibration menu, select ISF Calibration from the Main Menu and press 
ENTER. Use the number buttons on the remote control to enter the ISF Calibration menu 
passcode when prompted and press ENTER again. Then, press MENU on the remote 
control. 
Reset Picture Adjust: To restore the ISF default image settings for the current input 
source ONLY, press the 
 button to highlight “Yes” then press ENTER....

Operation
Runco CL-810 Series Owner’s Operating Manual 47 
PREL
IMINARY
Splash Screen Timer: Use the  or  button to set the Splash Screen Timer. This timer 
controls how long the startup (ISF and Runco logo) image stays on-screen after you turn 
on the projector. Select from 5 to 60 seconds, in 1-second increments. When finished, 
press EXIT. 
ISF Enable: Use ISF Enable to control the display of the ISF logo on the CL-810 splash 
screen upon power-up. 
Return to User OSD: To exit the ISF Calibration...

Operation
48 Runco CL-810 Series Owner’s Operating Manual
PREL
IMINARY
Notes: