Runco Cl 810 Ultra Projector User Manual
Have a look at the manual Runco Cl 810 Ultra Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Runco CL-810 Series Owner’s Operating Manual 49 PREL IMINARY 5.1 Lamp Replacement The lamp should be replaced when it reaches the end of its life (typically 2000 hours), or sooner if a noticeable degradation in brightness occurs. Contact your Runco dealer to obtain a replacement lamp. 1. Turn off the projector and unplug the power cord. Allow the projector to cool down for approximately 45 minutes prior to removing the lamp assembly for replacement. 2. Loosen the two captive screws from the lamp cover. 3. Remove the lamp cover. 4. Remove the two lamp assembly mounting screws. 5. Grasp the lamp assembly handle and pull gently, removing the lamp module from the projector housing. 6. Install the new lamp module and replace the two screws. 7. Replace the lamp cover at the right side first and secure it with the two screws. 8. Turn on the power and select Reset Lamp Timer from the Set Up menu to reset the lamp timer (refer to Reset Lamp Timer on page 45). 5Maintenance and Troubleshooting
Maintenance and Troubleshooting 50 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY 5.2 Troubleshooting Tips Table 5-1 provides some general guidelines for troubleshooting problems you may encounter with the CL-810. If the suggested solutions fail to resolve the problem or if you encounter an issue not described here, please contact Runco Technical Support. Table 5-1. Troubleshooting Chart SymptomPossible Cause(s)Solution The projector does not turn on. The CL-810 is not plugged in or the AC outlet is not active. The main power switch (at the rear of the projector) is off. Lamp cover is not securely attached. Ensure that the CL-810 is plugged in and that the AC outlet is active. Turn on the power switch. Securely attach the lamp cover. The projector does not turn back on after it was powered off. The projector will not turn on for two minutes after power-off, to protect the lamp. Wait until the CL-810 completes its cool-down (POWER LED lights solid orange). The remote control does not work correctly. The batteries have run out. Replace the batteries. The projector is on and OSD menus appear, but there is no video image on-screen. Incorrect source selection. Source component is not turned on. Source component is connected incorrectly or not at all. Select the correct source. Turn on the source. Check cable connection from source component to projector. A projected image from a DVD is split or otherwise scrambled. DVD player is connected to the Component input and set to progressive scan mode. Turn off progressive scan on the DVD player. Image is blurred. The lens is not correctly focused. Adjust the focus with the remote control. Image is too bright and/or lacks definition in the bright areas of the image. Contrast is set too high. Lower the contrast setting. Image appears “washed out” and/or dark areas appear too bright. Brightness is set too high. Lower the brightness setting. Colors in the image are swapped; for example, reds appear blue or vice versa. The Red/Pr, Green/Y or Blue/Pb outputs from the source are connected to the wrong inputs on the CL-810. Ensure that the source outputs are connected to the correct CL-810 input.
Maintenance and Troubleshooting Runco CL-810 Series Owner’s Operating Manual 51 PREL IMINARY TEMP and LAMP LEDs are both flashing red. The lamp cover is open. Fans are not working properly. Close the lamp cover. Please contact your Runco dealer for assistance. LAMP LED lights solid red. The lamp has failed or exceeded its usage life. Replace the lamp with a new one. TEMP LED lights solid red. CL-810 internal temperature is too high. Power off the CL-810 and allow it to cool down. Ensure that the intake and exhaust vents are not blocked. Turn the projector back on. If the problem persists, please contact your Runco dealer for assistance. Table 5-1. Troubleshooting Chart (continued) Symptom Possible Cause(s) Solution
Maintenance and Troubleshooting 52 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Notes:
Runco CL-810 Series Owner’s Operating Manual 53 PREL IMINARY 6.1 RS-232 Connection and Port Configuration To interface the CL-810 with a home theater automation/control system or a PC running terminal emulation software: 1. Connect it to your control system or PC as shown in Figure 3-11. 2. Start a terminal session on your PC using a terminal-emulation program, such as HyperTerminal. 3. Configure the RS-232 controller or PC serial port as follows: no parity, 8 data bits, 1 stop bit and no flow control. Set the baud rate to match that of the projector (115200, 38400 or 9600). 4. Press . You should see a command prompt (>) in the terminal window. 5. Type a command from among those listed in Table 6-1 and press . For example, to change the aspect ratio to Letterbox, type x063x . 6.2 Serial Command Syntax Serial commands to the CL-810 take the following form: Commands are in ASCII format. Commands are not case-sensitive; X001X and x001x are equivalent. A carriage return MUST follow each command. 6Serial Communications The CL-810 will not accept serial commands for 20 seconds after it is turned on or off. Table 6-1. Serial Commands CodeFunction x001xPower On x002xPower Off x003xMenu x004xEnter x005xExit x006xUp (arrow key) x007xDown (arrow key) x008xLeft (arrow key) x009xRight (arrow key) x011xShow active source and aspect ratio information x021xKeypad 1 x022xKeypad 2 Note
Serial Communications 54 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY x023xKeypad 3 x024xKeypad 4 x025xKeypad 5 x026xKeypad 6 x027xKeypad 7 x028xKeypad 8 x029xKeypad 9 x030xKeypad 0 x031xStore image settings to Memory 1 x032xStore image settings to ISF Night x033xStore image settings to ISF Day x046xRestore image settings from Memory 1 x047xRestore image settings from ISF Night x048xRestore image settings from ISF Day x049xLoad default of current source x051xSingle source, full-screen x052xPIP - graphics on video x053xPIP - video on graphics x054xPBP - graphics by video x055xPBP - video by graphics x056xPIP - increase sub-window size x057xPIP - decrease sub-window size x058xSet PIP/PBP active window x061xAnamorphic (16:9) aspect ratio x062xStandard (4:3) aspect ratio x063xLetterbox aspect ratio x064xVirtualWide aspect ratio x065xCinema aspect ratio x066xVirtual Cinema aspect ratio x071xRS-232 baud rate = 9600 x072xRS-232 baud rate = 38400 x073xRS-232 baud rate = 115200 Table 6-1. Serial Commands (continued) Code Function
Serial Communications Runco CL-810 Series Owner’s Operating Manual 55 PREL IMINARY x081xImage orientation = floor front x082xImage orientation = ceiling front x083xImage orientation = floor rear x084xImage orientation = ceiling rear x091xLamp Power = 200W x092xLamp Power = 250W x121xOSD Language = English x122xOSD Language = French x123xOSD Language = Spanish x124xOSD Language = German x125xOSD Language = Italian x131xSwitch to Composite input x132xSwitch to S-Video input x133xSwitch to RGB-HD input x134xSwitch to DVI input (HDMI) x135xSwitch to Component 1 input x136xSwitch to Component 2 input x156xBackground Color = Blue x157xBackground Color = White x181xToggle Blue Image on/off x281xVertical Lens Shift = Up x282xVertical Lens Shift = Down x283xZoom In x284xZoom Out x285xFocus (rotate lens to right) x286xFocus (rotate lens to left) x287xRVR = Full On (open) x288xRVR = Full Off (closed) Table 6-1. Serial Commands (continued) Code Function
Serial Communications 56 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Notes:
Runco CL-810 Series Owner’s Operating Manual 57 PREL IMINARY 7.1 CL-810 Specifications Table 7-1 lists the CL-810 specifications. 7Specifications Table 7-1. CL-810 Specifications Projector Type:Digital Light Processing (DLP), Single-Chip SuperOnyx DMD Native Resolution:1280 x 720 (16:9) Aspect Ratios:4:3, Letterbox, 16:9 Anamorphic, VirtualWide, Cinema, Virtual Cinema Video Standards:NTSC, PAL, SECAM DTV Compatibility:480p, 576p, 720p, 1080i Scan Frequency:Horizontal: 15 - 80 kHz Vertical: 50 - 100 Hz Picture Size (16:9 Screen):Recommended Width: 72 in. (1.83 m) to 96 in. (2.44 m) Capable of screen widths between 48 in. (1.22 m) and 200 in. (5.08 m) Throw Distance (Factor x Screen Width):CL-810: 1.80 to 2.43 CL-810 Ultra: Refer to Table 3-3 Horizontal and Vertical Offset:Refer to Table 3-4
Specifications 58 Runco CL-810 Series Owner’s Operating Manual PRELI MINARY Brightness and Contrast: Cinema Standards Measurement System (CSMS) Specifications - Brightness*: 14.5 to 21.6 foot-Lamberts (fL) - Contrast Ratio*: 200:1 to 220:1 *Variable depending on RVR setting These measurements are taken from the projector in a controlled, home theater environment. All measurements are made to ANSI/NAPM IT7.228-1997 specifications using the Photo Research PR-650 SpectraColorimeter and Minolta LS-100 Luminance Meter, Video Essentials test DVD and a 1.3 gain, 72-inch wide screen. The projector is calibrated to a color temperature of 6,500K and has a minimum of 150 hours of usage. The foot-Lambert (fL) is the unit of measurement used in commercial movie theaters to express image brightness at the screen surface. The Society of Motion Picture and Television Engineers (SMPTE) specifies 16 fL as the target image brightness for film-based projectors using an open gate (without film in the projector). More importantly, today SMPTE specifies 12 fL as the target image brightness in Digital Cinema theaters. The foot-Lambert measurement is dependent on screen size, screen gain and projector light output. Home Theater Calibration Specifications - Light Output: 442 to 587 ANSI Lumens - Contrast Ratio*: 200:1 to 220:1 These specifications are obtained by calibrating the projector as described above for CSMS measurements. Industry-Standard Specifications - Light Output: 1250 ANSI Lumens - Contrast Ratio: 1500:1 to 3100:1 These are typical projector brightness and contrast specifications found in most companies’ sales literature. Runco includes these measurements in its literature to allow for direct comparison with other manufacturers’ projectors. These measurements are typically taken at 9,000K to 13,000K to get expected performance data when the projector is used in professional, commercial and industrial displays. Lamp:250 Watts Estimated Lamp Life: 2000 hours Video Inputs: (1) Composite Video, (1) S-Video, (1) RGB/Component Video (BNC connectors), (1) RCA Component Video, (1) HDMI Control Options:- Discrete IR remote - Serial commands via RS-232 RS-232 Communication Parameters: 9600, 38400 or 115200 bps, no parity, 8 data bits, 1 stop bit, no flow control 12V Output:Max. 0.25 Amps, active when Cinema or Virtual Cinema Aspect Ratio is selected (CineWide versions only) or when projector is turned on Power Requirements:100 to 240 VAC (auto-sensing), 50/60 Hz, 310 Watts Operating Environment:41°F to 95°F (5°C to 35°C), 20% to 80% humidity (non-condensing) Dimensions:CL-810: See Figure 7-1 CL-810 Ultra: See Figure 7-2 Table 7-1. CL-810 Specifications (continued)