Runco Cl 810 Ultra Projector User Manual
Have a look at the manual Runco Cl 810 Ultra Projector User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 123 Runco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Installation Runco CL-810 Series Owner’s Operating Manual 19 PREL IMINARY Figure 3-4. Horizontal Lens Shift 0%Screen Center 100% Width Lens Shift (1.0 x W) 50% Width Lens Shift (0.5 x W) 150% Width Lens Shift (1.5 x W) Screen Width (W) Note: This is a general example of lens shift. Lenses vary in their shift capabilities. No particular lens is used in this example.
Installation 20 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Table 3-4 lists the lens shift limits for each available CL-810 lens, as percentages and absolute measurements with a 100 x 56 inch (1.78:1) screen. Table 3-4. Vertical and Horizontal Lens Shift Limits Lens Option CL-810CL-810 Ultra --Proteus AProteus BProteus CProteus DProteus EProteus F Lens Shift Limits, as Percentages of Screen Height or Width (Notes 1 and 2) Vertical (Note 2)Up50%2%11%10%13%14%20% Down50%2%72%70%70%71%63% Horizontal (Note 2)Left0%0%13% Right0%0%13% Lens Shift Limits in Inches, with a 100-by-56 inch (1.78:1) Screen VerticalUp28.001.126.165.607.287.8411.20 Down28.001.1240.3239.2039.2039.7635.28 HorizontalLeft0013.00 Right0013.00 Notes: 1. With no vertical or horizontal lens shift, the lens center and screen center are aligned with each other. 2. Vertical shift limits are percentages of the screen height. Horizontal shift limits are percentages of the screen width. 3. Vertical lens shift figures apply to ceiling mount configurations. For floor installations (where the projector is upright), reverse the up/down vertical offset percentages.
Installation Runco CL-810 Series Owner’s Operating Manual 21 PREL IMINARY Folded OpticsIn rear-screen applications where space behind the projector is limited, a mirror may be used to fold the optical path, as shown in Figure 3-5. The position of the projector and mirror must be accurately set. If you are considering this type of installation, contact your dealer for assistance. Figure 3-5. Folded Optics Other ConsiderationsOther considerations and tips that can help improve your installation: Keep the ambient temperature constant and below 35°C (95°F). Keep the projector away from heating and/or air conditioning vents. Changes in temperature may cause drifts in the projector circuitry, which may affect performance. Keep the projector away from devices that radiate electromagnetic energy such as motors and transformers. Common sources of these include slide projectors, speakers, power amplifiers and elevators. 3.4 Installing the Optional CineWide Lens If you are installing a CL-810 or CL-810 Ultra with the optional CineWide or CineWide with AutoScope system, install the secondary anamorphic lens in accordance with the instructions provided with the lens installation kit. Screen Mirror
Installation 22 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY 3.5 Mounting the CL-810 There are several methods for mounting the projector. Depending on your chosen installation, one method may be more suitable than another. Floor MountingIn typical front and rear screen installations, the projector can be mounted to a secure and level surface such as a table or cart. Carts are useful when moving a projector during a presentation or from site to site. If possible, lock the wheels when it’s in position to prevent it from being moved during a presentation. Ceiling MountingThe projector can also be inverted and suspended from the ceiling using a specially-designed ceiling mount fixture. This type of mounting is recommended for fixed installations and for those that want the projector out of sight or have a limited space for projector and audience. Adjusting the Projector Height or Projection Angle If the screen is significantly higher or lower than the projector, you can also tilt the projector at a slight angle. In a ceiling installation, you do this by adjusting the ceiling mount. For a floor installation, turn the four adjustable feet on the bottom of the projector to adjust the projector height and/or projection angle. If you do this, you may need to make keystone adjustments or vertically shift the image using the on-screen display (OSD) controls, to compensate. For detailed instructions, refer to Using the On-Screen Menus on page 31. ➤ ➤ Use only the Runco-approved ceiling mount kit designed for your projector. Install the mount kit according to the instructions provided with it. Note ➤
Installation Runco CL-810 Series Owner’s Operating Manual 23 PREL IMINARY 3.6 Connections to the CL-810 Proceed as follows to connect the CL-810 to your video sources, external controller(s) -- if present -- and AC power. When connecting your equipment: Turn off all equipment before making any connections. Use the correct signal cables for each source. Ensure that the cables are securely connected. Tighten the thumbscrews on connectors that have them. Connector Panel AccessTo access the connector panel, pull firmly on the cable access cover to open it. Connecting the SDC-1 System Expansion Device to the CL-810 If (and ONLY if) your installation includes an SDC-1 System Expansion Device: Use a Runco R-Link cable to connect the SDC-1 output to the CL-810 R-Link input; see Figure 3-6. All signal sources should then be connected to the appropriate inputs on the rear panel of the SDC-1. The signal from the SDC-1 is then output to the CL-810 projector via the R-Link cable. For detailed instructions, refer to the SDC-1 Owner’s Operating Manual. Figure 3-6. Connecting the CL-810 to the SDC-1 Connect ONLY an SDC-1 to the R-Link input! Although the R-Link looks like a DVI input, it does not function like one and cannot be used as an additional video input.Note S-VID /S-VID HDMI 2HDMI / DVI HDMI 1V H B(Pb/Cb) G(Y) R (Pr/Cr) V H B(Pb/Cb) G(Y) R (Pr/Cr) HD-1 INPUTSRunco International Union City, CA S-VIDEO TVIDEO DIGITAL INPUTS HD-2 INPUTS OUTPUTS TO PROJECTOR BOTH OUTPUTS MUST BE CONNECTED TO PROJECTORSerial No SDC-1SYSTEM EXPANSION DEVICE CL-810/SDC-1 Connector Panel SDC-1 Rear Panel R-LINK IN (from SDC-1 Controller R-Link Output to Projector R-Link Input)
Installation 24 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Connecting Source Components to the CL-810 If your installation does not include an SDC-1: Connect your video sources to the CL-810 as shown and described in the sections that follow. HDMI/DVI Connections: See Figure 3-7. With an HDMI source, use the included HDMI-to-HDMI cable; with a DVI source, use the included DVI-to-HDMI cable. Figure 3-7. HDMI/DVI Source Connections ➤ Use the HDMI input whenever possible. This ensures the highest video quality because the signal is carried in the digital domain throughout the entire signal path, from source component output into the projector. Tip S-VID /S-VID HDMI or DVI Source (DVD Player or HD Set Top Box)
Installation Runco CL-810 Series Owner’s Operating Manual 25 PREL IMINARY RGB Connections: Connect your personal computer or other RGB source (DVD player or HD set top box) to the COMP 2/RGB input; see Figure 3-8. You can use the included DB15HD-to-5 x BNC cable if your RGB source has a 15-pin, VGA-type connector. Figure 3-8. RGB Connections Progressive Component Video Connections: Connect your progressive component source (DVD player or HD set top box) to the COMP 2/RGB input as shown in Figure 3-9. Figure 3-9. Progressive Component Video Connections S-VID /S-VIDS-VID /S-VID DVD Player or HD Set Top Box Green Blue Red Horiz VertGreen Blue Red Horiz Vert Personal Computer S-VID /S-VID DTV or Progressive Component (YPbPr) Source Y Pb Pr
Installation 26 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Composite/S-Video/Component Video Connections: Use the included cables to connect your composite, S-Video and SD (480i) component video sources to the CL-810 as shown in Figure 3-10. Figure 3-10. Composite, S-Video and Component Video Connections S-VID /S-VID DTV Source, DVD Player, VCR, Satellite Receiver etc.
Installation Runco CL-810 Series Owner’s Operating Manual 27 PREL IMINARY RS-232 Controller Connection Connect a PC or home theater control/automation system (if present) to the RS-232 port on the CL-810; see Figure 3-11. Use a standard, 4-wire RJ-11 telephone cable, wired straight-through. For more information about using this connection, refer to Serial Communications on page 53. Figure 3-11. RS-232 Control System Connection S-VID /S-VID 123457896 D-Sub 9-pin female RJ-11 MaleRJ-11 to D-Sub 9-pin Adapter (not included) 1 2 3 4 Ye l l o w Ye l l o w RedRedBlackGreen Green Black RS-232 Adapter Wiring D-Sub 9-pin female 4-pin RJ-11 Function 2 2 Transmit Data 3 3 Receive Data 5 1, 4 Ground 1, 4, 6, 7, 8, 9 -- Not Connected
Installation 28 Runco CL-810 Series Owner’s Operating Manual PREL IMINARY Connecting 12-Volt Trigger Output to External Theater Components If your CL-810 is equipped with a CineWide with AutoScope system, or if your home theater contains other devices that respond to 12-volt triggers (such as a retractable screen or screen mask), connect it to the 12-volt trigger output as shown in Figure 3-12. Figure 3-12. Connecting 12-Volt Trigger Outputs Connecting to AC PowerThe CL-810 ships with various types of AC power cords. Choose the one that is appropriate to your locale. Plug the female end of the power cord into the AC receptacle on the rear of the projector (AC 100V ~ 240V). Then, connect the other end to your AC power source. ➤ S-VID /S-VID to CineWide with AutoScope system or other home theater components (screen, screen mask etc.) 3.5-mm mini plug ➤ Power switch