Roland XC 540 User Manual

6-7 Correcting Misalignment for Printing or Cutting
109Chapter 6 Feature Reference
Description
Depending on the composition of the media, the positioning of printing and cutting may be misaligned even when
youre using crop marks. Make corrections for misaligned printing and cutting for the media youre using.
Default Setting
[FEED SETTING]: 0.0 mm
[SCAN SETTING]: 0.0 mm
Downloaded From ManualsPrinter.com Manuals 

110Chapter 6 Feature Reference
6-8 Setting How the Media Heating System Operates
Switching Off the Preheater, Print Heater, or Dryer
Procedure

Press  twice.
Use 
 to select the device.
Press 
 several times to select [OFF].
Press 
 to enable the setting.
Press .
Press 
 to go back to the original screen.
Description
This makes the temperature settings for the media heating system (preheater, print heater, and dryer), as well as
switching these devices on or off. When this is set to [OFF], these devices...

6-8 Setting How the Media Heating System Operates
111Chapter 6 Feature Reference
Determining How the Media Heating System Operates
Procedure

Hold down  and press .
Press .
Press .
Use 
 to make the setting.
Press 
 to enable the setting.
Press .
Press 
 to go back to the original screen.
Description
This feature comtrols the temperature of the media heating system automatically when  is dark.
[MENU] performs heating to the preset temperature at all times, without lowering the temperature when the 
is...

112Chapter 6 Feature Reference
6-9 Setting How the Auxiliary Dryer Operates
Switching the Drying-heater Unit On and Off
Procedure

Hold down  and press .
Press 
 twice.
Press .
Use 
 to select ENABLE or DISABLE
Press 
.
Press .
Press 
 to go back to the original screen.
Description
This switches the optional drying-heater unit on or off.
The machine settings govern the temperature setting for the drying-heater unit, so when installation is complete, set
[OPTIONAL DRYER] on the machine to ENABLE....

6-9 Setting How the Auxiliary Dryer Operates
113Chapter 6 Feature reference
Switching the Optional Blower-fan Unit On and Off
Procedure

Hold down  and press .
Press 
.
Press .
Use 
 to select ENABLE or DISABLE
Press 
.
Press .
Press 
 to go back to the original screen.
Description
This switches the blower-fan unit on or off.
When the blower-fan unit is installed, set [BLOWER FAN] to ENABLE.
Default Setting
[BLOWER FAN]: DISABLE
W  1346mm
SETUP    SHEET
        ROLL
HEATER MENU
BLOWER FAN
BLOWER FAN...

114Chapter 6 Feature Reference
6-10 Saving the Printer Settings to Match the Media
Saving Optimized Media Settings As Preset Values
Procedure

Press .
Press .
Press 
.
Press .
Use
 to select any one from NAME1 to NAME8.
Press 
 to save.
The present menu settings are saved in the preset you chose in step 

Press .
Press 
  to go back to the original screen.
Description
Using the [PRESET] menu lets you easily change a wide variety of settings to optimize them for the media.
Making changes for each menu...

6-10  Saving the Pinter Settings to Match the Media
115Chapter 6 Feature reference
Menu Items That Can Be Saved in Presets
[PRE] (Pre heater)
[PRINT] (Print heater)
[DRYER]
 P.36 Settings of the Media Heating System
[EDGE DETECTION]
 P.86 Using Transparent Media
[SCAN INTERVAL]
 P.86 Printing Hard-to-dry Media
[VACUUM POWER]
 P.87 Preventing Media from Coming Loose
[FULL WIDTH  S]
 P.88 Speeding Up Output for Narrow Media
[FEED FOR DRY]
 P.93 Drying the Trailing Edge of the Printing Area on the...

6-10 Saving the Printer Settings to Match the Media
116Chapter 6 Feature Reference
Loading a Saved Preset
Procedure

Press .
Press  twice.
Use 
 to select the name of a preset you want to load.
Press  to load.
The settings are changed and the screen shown in the figure appears.
Description
This loads a saved preset. You can select any one of eight types of presets. (When no names have been assigned, you
select from among NAME1 through NAME8.)
If you load a preset while
 is illuminated, goes dark. To...

117Chapter 6 Feature Reference
6-11 Making the Network Settings
Setting IP address, Subnet mask, etc.
Procedure

Press .
Press 
 several times.
Press .
Press 
.
Press .
Use 
 to choose the item whose setting you want to
make.
Press  twice.
Use 
 to select the address number.
Press .
Repeat  and  to set all the address numbers.
When you have finished making the setting, press
.
Press .
Press 
 to go back to the original screen.
Description
Make sure the machine is connected to the network by an...

118Chapter 6 Feature Reference
6-12 Viewing System Information
Viewing the Serial Number, Firmware Version, and Other Information
Procedure

Press .
Press 
 several times.
Press .
Use 
 to choose the information you want to view.
Press .
Press .
Press 
 to go back to the original screen.
Description
You can view the following information.
[MODEL]: model name
[SERIAL NO.]: serial number
[INK]: ink type
[FIRMWARE]: firmware version
Viewing the Network Settings
Procedure

Press .
Press 
 several times....