Roland XC 540 User Manual

7-8 If a Error Message Appears
139Chapter 7 What to Do If
[PINCHROLL ERROR  LOWER PINCHROLL]
 was pressed without first lowering the pinch
rollers.
Press any key to clear the error. Pull back the loading lever,
then press 
.
The pinch rollers were raised while  was illu-
minated.
The error is cleared automatically after a short wait. Never
move the loading lever while printing is in progress.
[SERVICE CALL xxxx]
An unrecoverable error occurred, or part replace-
ment that must be performed by a service...

140
Downloaded From ManualsPrinter.com Manuals 

141
Chapter 8
Appendix
Downloaded From ManualsPrinter.com Manuals 

142Chapter 8 Appendix
8-1 Usable Media
Conditions for Usable Media
Media width
10-1/4 to 54 inches (260 to 1371 mm)
A) Cuttable media thickness
0.08 to 0.22 mm (3.2 to 8.6 mil)
(depending on media composition)
B) Maximum media thickness (including backing paper)
Printing only : 1.0 mm (39 mil)
When performing cutting : 0.4 mm (15 mil)
C) Roll outer diameter
180 mm
D) Paper tube (core) inner diameter
50.8 mm or 76.2 mm (2 inches or 3 inches)
Roll weight
30 kg (66 lb.)
Other conditions
Media such as the...

8-1 Usable Media
143Chapter 8 Appendix
Acceptable Media Width
260 to 1371 mm (10-1/4 to 54 in.)
Important!
Make sure the left and right pinch rollers are positioned above the grit rollers.
Use the middle pinch roller as required. Position one (or both) middle pinch rollers so as to form equally spaced
intervals along the width of the media.
Approx. 410 mm (16-1/8 in.)
Approx. 405 mm (15-15/16 in.)
Approx. 605 mm (23-13/16 in.)
Approx. 605 mm (23-13/16 in.)
Approx. 805 mm (31-11/16 in.)
Approx. 830 mm...

144Chapter 8 Appendix
8-2 Printing/Cutting Area
Maximum Area
The printing or cutting area along the horizontal plane (the direction in which the carriage moves) is determined by the
position of the pinch rollers.
Maximum Area When Using Crop Marks
When crop marks are used, the printing or cutting area is reduced from the maximum area by an amount equal to the
crop marks.
12.5 mm
12.5 mm12.5 mm
12.5 mm 10 mm
10 mm 10 mm
10 mm
Crop mark Maximum area Printing or cutting area
90 mm Max. 1346 mm
Printing or...

8-2 Printing/Cutting Area
145Chapter 8 Appendix
The Media-cutoff Location During Continuous Printing
When a media-cutoff command is sent from the computer, the cutoff location on the media is as shown in the figure
below.
First page75mm
Margin
(setting on the computer) Second page
Location where
separated
Downloaded From ManualsPrinter.com Manuals 

146Chapter 8 Appendix
Blade
ZEC-U1005
ZEC-U5025
Media
General Signage Vinyl
General Signage Vinyl
Fluorescent Vinyl
Reflective Vinyl
Tool-force
50  to  150 gf
30  to  100 gf
120  to  200 gf
100  to  200 gf
Amount of cutter offset
0.25 mm
0.25 mm
0.25 mm
0.25 mm
Life of a blade*
(General guide)
8000 m
4000 m
4000 m
4000 m
8-3 About the Blade
The cutting conditions and the service life of the blade change according to the media and the operating environment,
even when using identical blades. The service...

147Chapter 8 Appendix
8-4 Locations of the Power Rating and Serial Number Labels
Power RatingUse an electrical outlet that meets the requirements
for voltage, frequency, and amperage given here.
Serial NumberThis is require when you seek maintenance, servic-
ing, or support. Never peel off the label or let it get
dirty.
Downloaded From ManualsPrinter.com Manuals 

148Chapter 8 Appendix
Printing/Cutting method
Acceptable media widths
Printing/Cutting width (*1)
Ink cartridges Types
Color
Printing resolution (Printing dot resolu-
tion)
Acceptable tool
Cutting speed
Blade force
Blade offset compensation
Software resolution (When cutting)
Distance accuracy (When printing) (*2)
(*3)
Distance accuracy (When cutting) (*3)
Repetition accuracy (When cutting) (*3)
(*5)
Alignment accuracy for printing and cut-
ting (*3) (*6)
Alignment accuracy for printing and cut-
ting when...