Roland XC 540 User Manual

79Chapter 3 Maintenance and Adjustment
5-6 When Moving the Unit
Procedures from Preparing to Move Through Reinstalling
To move the machine, you must completely drain all ink inside the machine and secure the print heads in place with
Packing materials to protect them. Attempting to move the machine without first doing this may result in damage to
internal components due to leaking ink or damage to the heads.
This operation requires eight UNUSED SOL INK cleaning cartridges. Have these on hand before you...

5-6 When Moving the Unit
80Chapter 3 Maintenance and Adjustment
2.Secure the print heads in place.

Remove the drain bottle and detach the bottle stand. Then attach the drain-tube cover.
Detach the blade holder.
Raise the loading lever.
Secure the print heads in place using the packing material.
Lower the roll media from the printer and detach the shafts.
If necessary, also detach the dancer roller, rail slider and standlegs.
The machine is now ready to be moved.
3.Immediately move the machine and...

81
Chapter 6
 Feature Reference
Downloaded From ManualsPrinter.com Manuals 

82Chapter 6 Feature Reference
6-1 Pausing or Canceling Output
Canceling Output Before It Finishes
Procedure

 Press 
 Hold down  for one second or longer.
 Stop sending output data from the computer.
Description
 pauses output.
Pressing 
 a second time here resumes printing, but a horizontal stripe is produced at the location where
printing was stopped. We do not recommend resuming printing.
Downloaded From ManualsPrinter.com Manuals 

83Chapter 6 Feature Reference
6-2 Setting the Location for Starting Output
Setting the Output-start Location
Procedure

Use   to move the cutting car-
riage.
Align the center of the blade with the new output-start location.
 Press 
Description
You can use  to set the output-start location anywhere you want. Note, however that this setting must be made
for each individual page. When the printing of one page finishes, the output-start location returns to its default value.
When the location has been set,...

84Chapter 6 Feature Reference
6-3 Matching the Printer to the Operating Environment
Making the Setting for Automatic Adjustment of the Printer to the Operating Environment
Procedure

Press .
Press 
.
Press .
Press 
.
Press .
Use 
 to select EABLE.
Press 
 to enable the setting.
Press .
Press 
 to go back to the original screen.
Description
This setting enables or disables the feature for automatic adjustment to optimize the state of the machine to the
environment where it is used (temperature and...

85Chapter 6 Feature Reference
6-4 Accommodating Various Kinds of Media
Adjusting Head Height to Match Media Thickness
Procedure

Press .
Press 
 several times.
Press .
Open the front cover.
Move the lever to adjust the height of the head.
Moving the lever to High makes a warning beep sound
twice. Moving it to Low makes the warning beep
sound once.
Close the front vcover.
Press 
 to enable the setting.
Press .
Press 
 to go back to the original screen.
Description
Depending on the media, media may...

6-4 Accommodating Various Kinds of Media
86Chapter 6 Feature Reference
Using Transparent  Media
Procedure

Press .
Press 
 several times .
Press .
Use 
 to select DISABLE.
Press 
 to enable the setting.
Press .
Press 
 to go back to the original screen.
Description
This setting enables or disables detection of the leading and trailing edges of the media. It is normally set to ENABLE.
When transparent media is loaded, set it to DISABLE. When this is set to DISABLE, the ROLL and TU selections
are...

6-4  Accommodating Various Kinds of Media
87Chapter 6 Feature Reference
Description
You use this when ink dries poorly even when the print heater and dryer are used. Larger values produce progressively
slower movement of the media, enabling you to extend the drying time accordingly. Printing time takes correspond-
ingly longer.
You can also make this setting on the computer. When you have made the setting on the computer, the computers
setting is used and the printers setting is ignored.
Default Setting...

6-4 Accommodating Various Kinds of Media
88Chapter 6 Feature Reference
Speeding Up Output for Narrow Media
Procedure

Press .
Press 
 several times.
Press .
Press 
 several times.
Press .
Use 
 to select SHEET or OFF.
Press 
 to enable the setting.
Press .
Press 
 to go back to the original screen.
Description
This shortens output time by reducing the width of head movement to the minimum necessary. This is effective when
the width of the media or the output data is narrow.
SHEET matches the range of...