Roland XC 540 User Manual

5-3 Cleaning the Heads Using the Cleaning Kit
69Chapter 3 Maintenance and Adjustment
1.Change to the print-head manual-cleaning mode.

Press .
Press 
 several times.
Press .
Press 
.
Press .
Press .
Open the front cover and remove the maintenance cover.
Close the front cover.
Press 
.
The print-head carriage moves to the left side of the machine, and
then the screen shown in the figure appears.
	Open the front cover.
Preparations are complete when this screen appears.

Touch the location shown in the...

5-3 Cleaning the Heads Using the Cleaning Kit
70Chapter 3 Maintenance and Adjustment
2.Clean using the cleaning stick. Be especially careful to clean away any fibrous dust (lint).
Clean in the sequence shown in the figure below.
Never touch the nozzle surface.
Clean only the metal frame.
Area to clean
Area to cleanArea to clean
Area to cleanGently stroke the sponge.
Never rub with force.
Cleaning stick
Be sure to clean using one of the included cleaning sticks.
Downloaded From ManualsPrinter.com Manuals 

5-3 Cleaning the Heads Using the Cleaning Kit
71Chapter 3 Maintenance and Adjustment
3.Quit the manual cleaning mode.

Close the front cover.
Press 
.
The print-head carriage moves to the right side of the machine, and then the
screen shown in the figure appears.
Open the front cover and close the maintenance cover.
Close the front cover.
Press .
Press 
 to go back to the original screen.
4.Perform a printing test to verify the results of the procedure.
Perform a printing test to check the results....

72Chapter 3 Maintenance and Adjustment
5-4 Replacing Consumable Parts
Replacing the Wipers
The wipers are components that you use when cleaning the print heads. When the screen displays a message like the
one shown, it means the item needs to be  replaced. Replace with new items.
Important Notes on This Procedure
➢To prevent the heads from drying out, finish this procedure in 30 minutes or less.
➢A warning beep sounds after 30 minutes. At this time, stop work, attach the right side cover, and press 
....

5-4 Replacing Consumable Parts
73Chapter 3 Maintenance and Adjustment
2.Replace the wipers. Use the included tweezers.

Detach the old wipers.
Detach the hook and pull up and out.
Insert the new wipers.
Attach the hook.
3.Quit the [REPLACE WIPER] menu.

Close the front door.
Press 
.
After the process to quit the [REPLACE WIPER] menu ends, the screen shown in
the figure appears.
Press .
Press 
 to go back to the original screen.
Perform a printing test to verify the results of the procedure.
 P.40...

5-4 Replacing Consumable Parts
74Chapter 3 Maintenance and Adjustment
Replacing the Blade
If the blade becomes dull, replace it with the included replacement blade.
CAUTIONBe sure to perform operations as specified by these instructions, and never touch
any area not specified in the instructions.
Sudden movement of the machine may cause injury.
CAUTIONDo not touch the tip of the separating knife with your fingers.
Doing so may result in injury.
1.Enter the blade replacement mode.

Press .
Press 
 several...

5-4 Replacing Consumable Parts
75Chapter 3 Maintenance and Adjustment
Remove the old blade.
Install a new blade.
Reinstall the blade holder.
If installed without supporting the screw in this way, cutting quality
may become poor.
Tighten the screw.
Tug the blade holder upward to make sure it does not come loose.
3.Quit the [REPLACE KNIFE] menu.
Close the front cover, and press .
It snaps into place with
an audible click.
New blade Push-pin
Blade holder
Screw
Screw
Blade holder
Old blade
Press this...

5-4 Replacing Consumable Parts
76Chapter 3 Maintenance and Adjustment
Replacing the Separating Knife
If the separating knife becomes dull, replace it with the included replacement blade.
CAUTIONBe sure to perform operations as specified by these instructions, and never touch
any area not specified in the instructions.
Sudden movement of the machine may cause injury.
CAUTIONDo not touch the tip of the separating knife with your fingers.
Doing so may result in injury.
1.Enter the blade replacement mode....

5-4 Replacing Consumable Parts
77Chapter 3 Maintenance and Adjustment
Slowly insert it into the groove.
Tighten the screw.
Take care to ensure that the knife does not slip out of
position at this time.
3.Quit the [REPLACE KNIFE] menu.
Close the front cover, and press .
Downloaded From ManualsPrinter.com Manuals 

78Chapter 3 Maintenance and Adjustment
5-5 When Not in Use for a Prolonged Period
Keep Performing Maintenance
Switch On the Power Once a Month
Switch on the sub power once a month. When you turn on the power, the machine automatically performs some
operations such as those to keep the print heads from drying out. Allowing the machine to stand completely unused
for a prolonged period may damage the print heads, so be sure to switch on the power to perform these automatic
operations.
Keep at a Constant...