Ricoh Projector PJ X3351N User Manual
Here you can view all the pages of manual Ricoh Projector PJ X3351N User Manual. The Ricoh manuals for Projector are available online for free. You can easily download all the documents as PDF.
Page 131
![Page 131
ItemEco Time RatioDisplays the ratio of the time eco mode was used to the total use time.Current TimeDisplays the current time specified in [Current Time] in [Default Settings 2].Main FW VersionDisplays the version of the firmware on the main board.Interactive VersionWhen the interactive kit is connected to the projector, the version of the interactive function is
displayed.Display Status
129](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-130.png "Page 131
ItemEco Time RatioDisplays the ratio of the time eco mode was used to the total use time.Current TimeDisplays the current time specified in [Current Time] in [Default Settings 2].Main FW VersionDisplays the version of the firmware on the main board.Interactive VersionWhen the interactive kit is connected to the projector, the version of the interactive function is
displayed.Display Status
129")
ItemEco Time RatioDisplays the ratio of the time eco mode was used to the total use time.Current TimeDisplays the current time specified in [Current Time] in [Default Settings 2].Main FW VersionDisplays the version of the firmware on the main board.Interactive VersionWhen the interactive kit is connected to the projector, the version of the interactive function is displayed.Display Status 129
Page 132
5. Changing the Projector Settings 130
Page 133
![Page 133
6. Troubleshooting
This chapter explains the basic problems and troubleshooting methods when an indicator light is lit.
Indicator Display List The projector uses the [Power] button, indicators, and beeps to notify you if a malfunction occurs. Check
the indicator's status, and implement the following measures. "
" in the table means the indicator is
flashing.
Indicator location
1. [Power] button
2. Lamp indicator
3. Temp indicator
StatusCausesSolutionsThe projector does not turn
on.The...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-132.png "Page 133
6. Troubleshooting
This chapter explains the basic problems and troubleshooting methods when an indicator light is lit.
Indicator Display List The projector uses the [Power] button, indicators, and beeps to notify you if a malfunction occurs. Check
the indicator's status, and implement the following measures. \"
\" in the table means the indicator is
flashing.
Indicator location
1. [Power] button
2. Lamp indicator
3. Temp indicator
StatusCausesSolutionsThe projector does not turn
on.The...")
6. Troubleshooting This chapter explains the basic problems and troubleshooting methods when an indicator light is lit. Indicator Display List The projector uses the [Power] button, indicators, and beeps to notify you if a malfunction occurs. Check the indicator's status, and implement the following measures. " " in the table means the indicator is flashing. Indicator location 1. [Power] button 2. Lamp indicator 3. Temp indicator StatusCausesSolutionsThe projector does not turn on.The...
Page 134
![Page 134
StatusCausesSolutions"Hardware Error" was
displayed, and the projector
turned off during operation.
Flashing interval : 0.2
seconds
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp does not turn on.• The lamp has overheated and cannot turn on.
• The...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-133.png "Page 134
StatusCausesSolutions\"Hardware Error\" was
displayed, and the projector
turned off during operation.
Flashing interval : 0.2
seconds
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp does not turn on.• The lamp has overheated and cannot turn on.
• The...")
StatusCausesSolutions"Hardware Error" was displayed, and the projector turned off during operation. Flashing interval : 0.2 seconds The projector has malfunctioned.Disconnect the power cord, wait a while, and then turn on the projector again. You can also press and hold the [Power] button on the remote control or the control panel for two seconds. If the problem cannot be resolved, contact your service representative.The lamp does not turn on.• The lamp has overheated and cannot turn on. • The...
Page 135
![Page 135
StatusCausesSolutionsThe lamp does not turn on,
turned off during operation,
or it does not turn off.
Flashing interval: 0.2
seconds
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp turned off during
operation, or it does not turn
on.
Flashing interval: 1...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-134.png "Page 135
StatusCausesSolutionsThe lamp does not turn on,
turned off during operation,
or it does not turn off.
Flashing interval: 0.2
seconds
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp turned off during
operation, or it does not turn
on.
Flashing interval: 1...")
StatusCausesSolutionsThe lamp does not turn on, turned off during operation, or it does not turn off. Flashing interval: 0.2 seconds The projector has malfunctioned.Disconnect the power cord, wait a while, and then turn on the projector again. You can also press and hold the [Power] button on the remote control or the control panel for two seconds. If the problem cannot be resolved, contact your service representative.The lamp turned off during operation, or it does not turn on. Flashing interval: 1...
Page 136
![Page 136
StatusCausesSolutionsThe projector turned off
during operation, or it does
not turn on.
Flashing interval: 0.2
seconds
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp turned off during
operation.
Flashing interval: 1 second
• The interior has overheated.
•...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-135.png "Page 136
StatusCausesSolutionsThe projector turned off
during operation, or it does
not turn on.
Flashing interval: 0.2
seconds
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp turned off during
operation.
Flashing interval: 1 second
• The interior has overheated.
•...")
StatusCausesSolutionsThe projector turned off during operation, or it does not turn on. Flashing interval: 0.2 seconds The projector has malfunctioned.Disconnect the power cord, wait a while, and then turn on the projector again. You can also press and hold the [Power] button on the remote control or the control panel for two seconds. If the problem cannot be resolved, contact your service representative.The lamp turned off during operation. Flashing interval: 1 second • The interior has overheated. •...
Page 137
![Page 137
StatusCausesSolutionsThe lamp does not turn on.
Flashing interval: 1 second
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp turned off during
operation.
Flashing interval: 1 second
The projector has malfunctioned.Disconnect the power cord, wait a
while, and...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-136.png "Page 137
StatusCausesSolutionsThe lamp does not turn on.
Flashing interval: 1 second
The projector has malfunctioned.Disconnect the power cord, wait a
while, and then turn on the
projector again.
You can also press and hold the
[Power] button on the remote
control or the control panel for two
seconds.
If the problem cannot be resolved,
contact your service
representative.The lamp turned off during
operation.
Flashing interval: 1 second
The projector has malfunctioned.Disconnect the power cord, wait a
while, and...")
StatusCausesSolutionsThe lamp does not turn on. Flashing interval: 1 second The projector has malfunctioned.Disconnect the power cord, wait a while, and then turn on the projector again. You can also press and hold the [Power] button on the remote control or the control panel for two seconds. If the problem cannot be resolved, contact your service representative.The lamp turned off during operation. Flashing interval: 1 second The projector has malfunctioned.Disconnect the power cord, wait a while, and...
Page 138
![Page 138
Common Problems
If you think a malfunction has occurred, check the following before contacting your service
representative.ProblemSolutionsPower does not turn on.• Make sure the power plug or connector is connected correctly.
• Make sure the lamp cover is mounted correctly. For details, see page 146 "Replacing the Lamp".
• When the projector is installed on a ceiling and lens- down, be sure to press the [Power] button and wait until
the projector cooling process completes before
disconnecting the...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-137.png "Page 138
Common Problems
If you think a malfunction has occurred, check the following before contacting your service
representative.ProblemSolutionsPower does not turn on.• Make sure the power plug or connector is connected correctly.
• Make sure the lamp cover is mounted correctly. For details, see page 146 \"Replacing the Lamp\".
• When the projector is installed on a ceiling and lens- down, be sure to press the [Power] button and wait until
the projector cooling process completes before
disconnecting the...")
Common Problems If you think a malfunction has occurred, check the following before contacting your service representative.ProblemSolutionsPower does not turn on.• Make sure the power plug or connector is connected correctly. • Make sure the lamp cover is mounted correctly. For details, see page 146 "Replacing the Lamp". • When the projector is installed on a ceiling and lens- down, be sure to press the [Power] button and wait until the projector cooling process completes before disconnecting the...
Page 139
![Page 139
ProblemSolutionsNo image.• Make sure the input signal is switched correctly if [AutoInput Search] in [Default Settings 1] is set to [Off]. For
details, see page 105 "Default Settings 1 Menu".
• Make sure the AV mute function is not turned on. For details, see page 48 "Temporarily Blanking the Image
and Muting the Audio".
• Check the settings of [Brightness] in [Image Adjustment]. For details, see page 93 "Image Adjustment Menu".
• Make sure the computer or AV equipment is...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-138.png "Page 139
ProblemSolutionsNo image.• Make sure the input signal is switched correctly if [AutoInput Search] in [Default Settings 1] is set to [Off]. For
details, see page 105 \"Default Settings 1 Menu\".
• Make sure the AV mute function is not turned on. For details, see page 48 \"Temporarily Blanking the Image
and Muting the Audio\".
• Check the settings of [Brightness] in [Image Adjustment]. For details, see page 93 \"Image Adjustment Menu\".
• Make sure the computer or AV equipment is...")
ProblemSolutionsNo image.• Make sure the input signal is switched correctly if [AutoInput Search] in [Default Settings 1] is set to [Off]. For details, see page 105 "Default Settings 1 Menu". • Make sure the AV mute function is not turned on. For details, see page 48 "Temporarily Blanking the Image and Muting the Audio". • Check the settings of [Brightness] in [Image Adjustment]. For details, see page 93 "Image Adjustment Menu". • Make sure the computer or AV equipment is...
Page 140
![Page 140
ProblemSolutionsImage is not projected normally.• Make sure the input signal is compatible with theprojector. For details, see page 166 "List of Compatible
Signals".
• Check the status of the video tape or other video source.
• Execute [Auto Set Signals] in [Image Adjustment]. For details, see page 93 "Image Adjustment Menu".
• Check the settings of the computer's graphics driver. For details, see the manual provided with the computer.Image is blurred.
Image is partially out of...](http://img.usermanuals.tech/thumb/64/100047/w300_projector_manual_8920_d-139.png "Page 140
ProblemSolutionsImage is not projected normally.• Make sure the input signal is compatible with theprojector. For details, see page 166 \"List of Compatible
Signals\".
• Check the status of the video tape or other video source.
• Execute [Auto Set Signals] in [Image Adjustment]. For details, see page 93 \"Image Adjustment Menu\".
• Check the settings of the computer's graphics driver. For details, see the manual provided with the computer.Image is blurred.
Image is partially out of...")
ProblemSolutionsImage is not projected normally.• Make sure the input signal is compatible with theprojector. For details, see page 166 "List of Compatible Signals". • Check the status of the video tape or other video source. • Execute [Auto Set Signals] in [Image Adjustment]. For details, see page 93 "Image Adjustment Menu". • Check the settings of the computer's graphics driver. For details, see the manual provided with the computer.Image is blurred. Image is partially out of...