Ricoh Projector PJ X3351N User Manual

ItemDefaultAspectSelect the aspect ratio of the image.
This function is not available when you select [USB Memory] or [Server] as the input signal. When you select [Network PC] or [Miracast] as the
input signal, this function is available for the computer or smartphone screen you project.
When [4-corner Correction] is enabled, the setting is [Normal] and
cannot be changed.
• Normal Display in full screen without changing the input signal aspect ratio.
• 16:9 Display using 16:9 aspect ratio.• RICOH PJ...

ItemDefaultDisplay PositionMove the image if the projected image is smaller or larger than the
screen size. You can move the image using the [
], [], [], and []
buttons.
This function is not available when you select [Network PC], [USB
Memory], [Server], or [Miracast] as the input signal.
When [4-corner Correction] is enabled, the display position is initialized
and cannot be changed.
-Wall Color Mode
Select the image hue according to the projection surface when the imageis being projected on something...

ItemDefault3D Projection > 3D FormatSelect a 3D format.
Select [Auto] when the 3D signals are input through HDMI. If the image does not project in 3D even if [Auto] is selected, change the setting tomatch the 3D format of the signal being input.
• Auto
• Frame Sequential
• Side by Side
• Top and Bottom
• Frame PackingAutoClosed Caption
The projector supports closed captioning, which allows subtitles to be
displayed at the bottom of the picture. This is pursuant to the regulations
set forth by the US...

Energy Saving Settings MenuItemDefaultEco ModeSpecify the lamp settings to save energy or to make images brighter.• On (Auto) Select this mode to save energy. In this mode, the following settings
are automatically specified:
• Lamp Power: [Auto]
• Lamp Pwr on No Signal: [Eco]
• Image Eco: [On]
• On (Detailed) You can specify [Lamp Power], [Lamp Pwr on No Signal], and
[Image Eco] manually.
• Off Select this mode to make images brighter. In this mode, the following
settings are automatically specified:
•...

ItemDefaultLamp PowerThis setting is available when [Eco Mode] is set to [On (Detailed)].
Select the lamp power level.
[Auto] is selectable when you select [Standard] or [Rear] in [Projection
Mode] under [Default Settings 2]. If you select [Auto], the lamp power
level switches automatically depending on the brightness of the projecting location. Make sure that the illuminance sensor on the top of the projectoris not blocked. This function may not work correctly depending on thepositioning of the...

ItemDefaultPower Off on No SignalSelect the amount of time from the last input signal or operation until the
projector enters standby mode.
• Off
• 5 min.
• 10 min.
• 20 min.
• 30 min.20 min.Power on Standby
Specify whether or not to save energy while in standby.• Eco You can save energy while in standby, but start-up time is slower.
• Q'ck On You can turn on the projector quickly, and the projector starts
projection automatically if the image signals are input even while in
standby. However, the...

Default Settings 1 MenuItemDefaultAuto Input SearchSpecify whether or not to switch to another input signal that the projector
detects when you press the [Input] button. Always select the [Server] and
[Miracast] input signals manually even if this setting is [On].OnComputer 2 Terminal
Select the purpose of Computer2 In/Monitor Out port.• Input You can use Computer2 In/Monitor Out port for inputting RGB
signals.
• Output You can use Computer2 In/Monitor Out port for outputting RGB
signals and Y/Pb/Pr...

ItemDefaultUser Logo > Register LogoRegister a user logo. Project the image to be registered as a user logo,and then execute this function. User logos can be displayed in the start-upscreen or as the background when there are no input signals.
User logos can be registered up to the following resolutions: • RICOH PJ X3351N/X4241N: 1024 × 768 pixels
• RICOH PJ WX3351N/WX4241N: 1280 × 800 pixels
This function is available when you select [Computer 1], [Computer 2], or [HDMI] (RGB signals) as the input...

Default Settings 2 MenuItemDefaultLanguageSelect the display language.
Available languages are as follows:
English, Japanese, Spanish, Russian, French, Portuguese, German, Italian, Dutch, Polish, Czech, Swedish, Finnish, Hungarian, Norwegian,
Danish, Romanian, Greek, Turkish, Arabic, Thai, Indonesian, Traditional
Chinese.EnglishProjection Mode
Select the projection method according to how the projector ispositioned.
When you select [Ceiling] or [Rear Ceiling], you cannot select [Auto] in
[Lamp Power]...

ItemDefaultRemote Control IDSelect the projector remote control ID. Specify the ID for each projectorwhen operating multiple projectors using one remote control.
• 1
• 2
• 3
• 41Direct Power On
Select the power on method of the projector.• On Automatically turn on the projector when the power cord is
connected.
• Off Turn the projector on when the [Power] button is pressed.OffHigh Altitude Mode
The number of fan rotations is high when set to [On]. The air is thin at high
elevations, so the cooling...