Ricoh Projector PJ WX6181N User Manual

106
Conditions for using tiling
• All the projectors need to fulfil the following conditions.
• The panel size must be the same
•  The projection screen size must be the same
•  The left and right ends or top and bottom ends of the projection screen must be consistent.
•  The settings for the left and right edges of the edge blending are the same
•  The settings for the top and bottom edges of the edge blending are the same
  If the tiling conditions are satisfied, the video screen of the projector at...

107
❼ Menu Descriptions & Functions [SETUP]
[MENU]
Selecting Menu Language [LANGUAGE] 
You can choose one of 29 languages for on-screen instructions.
NOTE: Your setting will not be affected even when [RESET] is done from the menu.
Selecting Menu Color [COLOR SELECT]
You can choose between two options for menu color: COLOR and MONOCHROME.
Turning On / Off Source Display [INPUT DISPLAY]
This option turns on or off input name display such as HDMI1, HDMI2, DisplayPort, BNC, BNC(CV), BNC(Y/C), COMPUTER to be...

108
Turning On / Off Eco Message [ECO MESSAGE]
This option turns on or off the following messages when the projector is turned on. 
The Eco Message prompts the user to save energy. When [OFF] is selected for [ECO MODE], you will get a message to prompt 
you to select [ON] for [ECO MODE].
When [ON] is selected for [ECO MODE]
To close the message, press any one of the buttons. The message will disappear if no button operation is done for 30 seconds.
When [OFF] is selected for [ECO MODE]
Pressing the ENTER...

109
[INSTALLATION]
Selecting Projector Orientation [ORIENTATION]
This reorients your image for your type of projection. The options are: desktop front projection, ceiling rear projection, desktop 
rear projection, and ceiling front projection.
NOTE: 
• Please consult the retail store if you require special installation services e.g. when mounting the projector to a ceiling. Never install the projector on your own. This may 
result in the projector falling down and causing injury to people.
•  When using...

110
Selecting Aspect Ratio and Position for Screen [SCREEN TYPE]
Screen typeSets the aspect ratio of the projection screen.
FREE The ratio of the liquid crystal panel is selected. Select this when projecting multi-
screen and 17:9 screen (2K).
4:3 screen For a screen with a 4:3 aspect ratio
16:9 screen For a screen with a 16:9 aspect ratio
16:10 screen For a screen with a 16:10 aspect ratio
NOTE:
•  After changing the screen type, check the setting of [ASPECT RATIO] in the menu. (→ page 93)
Using the...

111
[LAMP MODE]
When eco-mode is set to [ON], the CO2 emissions (calculated from the reduction in power consumption) of the projector can be 
reduced. The eco-mode reduces power consumption by mainly lowering the brightness of the lamp. As a result, the lamp replace-
ment time (as a guide)* is extended. (→ page 31, 131)
*  Replacement time not guaranteed.
LAMP ADJUST ............ This can be set when the eco-mode is set to [OFF]. Adjust the lamp to ma\
tch the brightness of each 
projector when...

112
[CONTROL]
TOOLS
ADMINISTRATOR MODE
This allows you to select MENU MODE, save settings, and set a password for the administrator mode.
MENU MODESelect either [BASIC] or [ADVANCED] menu.
(→ page 84) —
NOT SAVE SETTING 
VALUES Placing a check mark will not save your projector settings.
Clear this check box to save your projector settings. —
NEW PASSWORD/CON-
FIRM PASSWORD Assign a password for the administrator mode.
Up to 10 alphanumeric 
characters
5. Using On-Screen Menu  

113
PROGRAM TIMER
This option turns on/standby the projector and changes video signals, and selects ECO mode automatically at\
 a specified time.
NOTE:
• Before using [PROGRAM TIMER], make sure that the [DATE AND TIME] feature is set. (→ page 115)
  Make sure that the projector is in the standby condition with the POWER cord connected.
  The projector has a built-in clock. The clock will keep working for about two weeks after the main power is turned off. If the main power is not supplied to the...

114
FUNCTION .....................Select a function to be executed. Selecting [POWER] will allow you to tu\
rn on or off the projector by setting 
[ADVANCED SETTINGS]. Selecting [INPUT] will allow you to select a video source by setting [ADVANCED 
SETTINGS]. Selecting [ECO MODE] will allow you to select [ECO MODE] by setting [ADVANCED SETTINGS].
ADVANCED SETTINGS
 ............................................. Select power on/off, a type of video source, or ECO MODE for the selected item in [FUNCTION]....

115
Activating the program timer
1. Select [ENABLE] on the [PROGRAM TIMER] screen and press the ENTER button.
  The selection screen will be displayed.
2.  Press the ▼ button to align the cursor with [ON] and then press the ENTER button.
  Return to the [PROGRAM TIMER] screen.
NOTE:
•  When the effective settings of the [PROGRAM TIMER] have not been set to [ON], the program will not be executed even if the [ACTIVE] items in the program list have 
been ticked.
•  Even when the effective settings of the...