Ricoh Projector PJ WX6181N User Manual

136
❾ Application Menu 
When [ETHERNET] is selected from the [INPUT] menu, the application menu [APPLICATION MENU] will be displayed.
The application menu allows you to set up the User Supportware and Network Settings (NETWORK SETTINGS).
The User Supportware is contained on the supplied CD-ROM.
[ADVANCED] and [BASIC] can be selected in the [MENU MODE] under [SETUP] → [CONTROL] → [TOOLS] → [ADMINISTRATOR 
MODE]. (→ page 112)
The [BASIC] menu contains minimum essentials of menus and commands. 
ADVANCED...

137
NETWORK PROJECTOR
This shows information for projector name, resolution, and network (wired/wireless) which are required to use Network Projector.
Use this information to set up for your computer.
REMOTE DESKTOP CONNECTION
This allows you to set up for computer name entry and effects for Remote Desktop.
NOTE:
• A USB keyboard is required to set up the Remote Desktop Connection.
5. Using On-Screen Menu  

138
NETWORK SETTINGS(MM)
Important:
• Consult with your network administrator about these settings.
•  When using a wired LAN, connect the LAN cable (Ethernet cable) to the Ethernet port (LAN) of the projector. (→ page 166) 
•  When using a wireless LAN, attach the wireless LAN unit sold separately to the projector. (→ page 167)
TIP: The [NETWORK SETTINGS(MM)] you make will not be affected even when [RESET] is done from the menu.
        About the Projector's [NETWORK SETTING].(→ page 6)
Hints on How...

139
WIRED LAN or WIRELESS LAN (ADVANCED menu only)
PROFILES• Up to two settings for the Ethernet port or USB wireless LAN unit 
can be stored in memory of the projector. Total of four settings can 
be stored.
  Five settings can be stored: two for the built-in Ethernet port, two 
for wireless LAN and one for WPS.
•  Select [PROFILE 1] or [PROFILE 2] and then do settings for [DHCP] 
and the other options. 
  After doing this, select [OK] and press the ENTER button. This will 
store your settings in...

140
DHCPPlace a check mark to automatically assign an IP address to the projector 
from your DHCP server.
Clear this check box to register the IP address or subnet mask number 
obtained from your network administrator. —
IP ADDRESS Set your IP address of the network connected to the projector when 
[DHCP] is turned off. Up to 12 numeric char-
acters
SUBNET MASK Set your subnet mask number of the network connected to the projector 
when [DHCP] is turned off. Up to 12 numeric char-
acters
GATEWAY Set the...

141
SECURITYThis will turn on or off the encryption mode for secure transmission.
To use encryption, specify a WEP key or encryption key. Select your 
security type appropriate for your computer and the wireless LAN unit.DISABLE .......................... Will not turn on the encryption feature. Your 
communications may be monitored by someone.
WEP(64bit) ................... Uses 64-bit datalength for secure transmission.
WEP(128bit) ................. Uses 128-bit datalength for secure transmission....

142
When [WPA-PSK], [WPA-EAP], [WPA2-PSK], or [WPA2-EAP] is selected for [SECURITY TYPE]
ENCRYPTION TYPESelect [TKIP] or [AES].
KEY Enter encryption key. Key length must be 8 or greater and 63 or less.
5. Using On-Screen Menu  

143
[AUTHENTICATION] (required for wireless only)
Setting is required for using WPA-EAP or WPA2-EAP. 
Preparation before setting
Select a wireless LAN compliant WPA-EAP or WPA2-EAP authentication and install a dig\
ital certificate on the projector.
1. Set [DATE AND TIME] on the projector. (→ page 116)
2.  Use a computer to save digital certificates (files) for WPA-EAP or WPA2-EAP setting to your USB memory device.
  After completing saving the file, remove the USB memory device from the computer.
NOTE:...

144
4. Select [SITE SURVEY] and press the ENTER button.
 The “SSID” list will be displayed.
5.  Select a connecting SSID, and then select [OK].
 Finally press the ENTER button.
• Select the SSID for which WPA-PSK or WPA2-PSK is set.
•  Select [INFRASTRUCTURE (
)] for [NETWORK TYPE]. WPA-PSK, WPA2-PSK, WPA-EAP, or WPA2-EAP is not availa\
ble when 
[AD HOC (
)] is selected.
6.  Select the [SECURITY] tab.
  The [SECURITY] page will be displayed.
7.  Select the [SECURITY TYPE] field and press the ENTER...

145
11. Select the [AUTHENTICATION] tab.
  The [AUTHENTICATION] page will be displayed.
  Select either [EAP-TLS] or [PEAP-MSCHAPv2] for [EAP TYPE]. The setting items vary depending on the EAP type.
  See the table below.
EAP Type Setting Item Note
EAP-TLS User Name 1 character or more and 32 characters or less
Client Certificate PKCS#12 format file
CA Certificate
(Certificate authority’s certificate) DER format file
PEAP-MSCHAPv2 User Name 1 character or more and 32 characters or less
Password 1...