Ricoh Mp C3000 Service Manual

Bit Switches 
SM 49 B786 
B786 
Fax Option 
So, the actual rx level is 256/-16 = -16 dB 
3  Not used   Do not change this setting. 
4 Line error mark print 
0: OFF, 1: ON (print)  When 1 is selected, a line error mark is printed 
on the printout if a line error occurs during 
reception. 
5 G3/G4 communication 
parameter display 
0: Disabled 
1: Enabled  This is a fault-finding aid. The LCD shows the key 
parameters (see below). This is normally disabled 
because it cancels the CSI display for the user....

Bit Switches 
B786 50  SM 
Always enabled (1,1): At any time, an RDS system can access the 
machine. 
 
System Switch 03 [SP No. 1-101-004]  
No  FUNCTION  COMMENTS 
0-7 Length of time that RDS is 
temporarily switched on when 
bits 6 and 7 of System Switch 
02 are set to “User selectable” 00 - 99 hours (BCD). 
This setting is only valid 
if bits 6 and 7 of System 
Switch 02 are set to “User selectable”. 
The default setting is 24 hours. 
 
System Switch 04 [SP No. 1-101-005]  
No  FUNCTION  COMMENTS...

Bit Switches 
SM 51 B786 
B786 
Fax Option 2  Automatic error report printout 
0: Disabled 1: Enabled  0: Error reports will not be printed. 
1: Error reports will be printed automatically after 
failed communications. 
3 
Printing of the error code on 
the error report 
0: No 1: Yes  1: Error codes are printed on the error reports. 
4 
Not used   Do not change this setting. 
5 Power failure report 
0: Disabled 1: Enabled  1: A power failure report will be automatically 
printed after the power is...

Bit Switches 
B786 52  SM 
System Switch 0C - Not used (Do not change the factory settings.) 
System Switch 0D - Not used (Do not change the factory settings.) 
 
System Switch 0E [SP No. 1-101-015]  
No  FUNCTION  COMMENTS 
0-1 Not used   Do not change the settings. 
2 Enable/disable for direct 
sending selection 
0: Direct sending off  
1: Direct sending on  Direct sending cannot operate when the capture 
function is on during sending. Setting this switch 
to 1 enables direct sending without capture....

Bit Switches 
SM 53 B786 
B786 
Fax Option 
0A: Sweden   1A: China 
0B: Switzerland  1B: Formosa 
0C: Portugal   1C: Korea 
0D: Netherland   20: Turkey 
0E: Spain   21: Greece 
0F: Israel  22: Hungary 
10: ---  23: Czech 
11: USA  24: Poland   
 
System Switch 10 [SP No. 1-101-017]  
No  FUNCTION  COMMENTS 
0-7 Threshold memory level for 
parallel memory transmission  Threshold = N x 128 KB + 256 KB 
N can be between 00 - FF(H) 
Default setting: 02(H) = 512 KB 
 
System Switch 11 [SP No. 1-101-018]  
No...

Bit Switches 
B786 54  SM 
the TTI from the left edge of the paper. If the TTI 
is moved too far to the right, it may overwrite the 
file number which is on the top right of the page. 
On an A4 page, if the TTI is moved over by more 
than 50 mm, it may overwrite the page number. 
 
System Switch 13 - Not used  (do not change these settings) 
System Switch 14 - Not used (do not change these settings) 
 
System Switch 15 [SP No. 1-101-022]  
No  FUNCTION  COMMENTS 
0 Not used   Do not change the settings....

Bit Switches 
SM 55 B786 
B786 
Fax Option 
 
System Switch 17 - Not used  (do not change these settings) 
System Switch 18 - Not used (do not change these settings) 
 
System Switch 19 [SP No. 1-101-026]  
No  FUNCTION   COMMENTS 
0-5 Not used   Do not change the settings. 
6 Extended scanner page 
memory after memory option 
is installed 
0: Disabled 
1: Enabled  0: After installing the memory expansion option, the 
scanner page memory is extended to 4 MB from 2 
MB.  
1: If this bit is set to 1 after...

Bit Switches 
B786 56  SM 
2 Destination telephone 
number display limitation 
0: OFF, 1: ON   When 1 is selected, the destination telephone 
number display is limited and redial is disabled. 
3 Operation selection without 
PIN code registered 
0: Transmission interrupted 
1: No interrupted 
transmission   0: When 0 is selected without PIN code 
registration, transmission is interrupted and an alert 
message shows on the LCD. 
4-7 
Not used   Do not change these settings. 
 
System Switch 1E [SP No....

Bit Switches 
SM 57 B786 
B786 
Fax Option 
the sender has an RTI or CSI  block me ssages from senders that do not include 
an RTI or CSI, change this bit to “1”, then enable 
Authorized Reception. 
Otherwise, keep this bit at “0 (default setting)”. 
5-7  Not used   Do not change the settings 
 
System Switch 1F [SP No. 1-101-032]  
No  FUNCTION  COMMENTS 
0 Not used   Do not change the settings. 
1 Report printout after an 
original jam during SAF 
storage or if the SAF memory 
fills up 
0: Enabled 
1:...

Bit Switches 
B786 58  SM 
3-6 Reserved 
7 Not used   is “A3” (Bit 2). 
When mail is sent, there is no negotiation with the 
receiving machine at the destination, so the 
sending machine cannot make a selection for the 
receiving capabilities (original width setting) of the 
receiving machine. The original width selected 
with this switch is used as the RX machine’s 
original width setting, and the original is reduced 
to this size before sending. The default is A4. 
If the width selected with this...