Ricoh Aficio MP 9000 User Manual

Interface Settings
53
2
❖IPv6 Stateless Address Autoconfiguration
You can set “IPv6 Stateless Address Autoconfiguration” to “Active” or “Inactive”.
Active
Inactive
❖DNS Configuration
Make settings for the DNS server.
When you select [Specify], enter the [DNS Server] IP address as “xxx.xxx.xxx.xxx(“x
indicates a number).
Auto-Obtain (DHCP)
Specify
 DNS Server 1: 000.000.000.000
 DNS Server 2: 000.000.000.000
 DNS Server 3: 000.000.000.000
❖DDNS Configuration
You can specify the DDNS settings....

System Settings
54
2
❖NCP Delivery Protocol
Select the protocol for NCP delivery.
IPX Priority
TCP/IP Priority
IPX Only
TCP/IP Only
❖NW Frame Type
Select the frame type when you use NetWare.
Auto Select
Ethernet II
 Ethernet 802.2
 Ethernet 802.3
 Ethernet SNAP
❖SMB Computer Name
Specify the SMB computer name.
Enter the computer name using up to 15 alphanumerical characters.
*+,/:;=?[\]|. and spaces cannot be entered.
Setting a computer name starting with RNP and rnp is inhibited.
Use uppercase...

Interface Settings
55
2
❖LAN Type
When you have installed the optional IEEE 802.11b interface unit, select inter-
face, IEEE 802.11b (wireless LAN) or Ethernet.
Ethernet
 IEEE 802.11b
Appears when the optional IEEE 802.11b interface unit is installed.
If Ethernet and IEEE 802.11b (wireless LAN) are both connected to the ma-
chine, the selected interface takes precedence.
❖Ping Command
Check the network connection with ping command using given IP address.
If you fail to connect to the network, check the...

System Settings
56
2
Parallel Interface
This section describes various items of [Parallel Interface] under [Interface Settings].
[Parallel Interface] is displayed when this machine is installed with the IEEE 1284
interface board (optional).
❖Parallel Timing
Sets the timing for the control signal of the parallel interface.
ACK outside
ACK inside
STB down
❖Parallel Communication Speed
Sets the communication speed for the parallel interface.
High Speed
Standard
❖Selection Signal Status
Sets the level...

Interface Settings
57
2
IEEE 1394
This section describes various items of [IEEE 1394] under [Interface Settings].
[IEEE 1394] is displayed when this machine is installed with the IEEE 1394 inter-
face board (optional).
❖IPv4 Address
When you connect the machine to a network using the IEEE 1394 interface,
you must configure the IP address and subnet mask.
When you select [Specify], enter the [Machine IPv4 Address] and [Sub-net Mask]
as “xxx.xxx.xxx.xxx”(“x” indicates a number).
When you use the IEEE 1394...

System Settings
58
2
❖WINS Configuration
You can specify the WINS server settings.
If [On] is selected, specify the [WINS Server] IP address as “xxx.xxx.xxx.xxx
(“xxx indicates a number).
If DHCP is in use, specify the [Scope ID].
Enter [Scope ID] using up to 31 alphanumeric characters.
On
 Primary WINS Server: 000.000.000.000
 Secondary WINS Server: 000.000.000.000
Scope ID
Off
❖IPv4 over 1394
When you use the IP over 1394 function of the IEEE 1394 interface to connect
the machine to the network,...

Interface Settings
59
2
IEEE 802.11b
This section describes various items of [IEEE 802.11b] under [Interface Settings].
[IEEE 802.11b] is displayed when this machine is installed with the wireless LAN
interface board (optional).
Implement respective settings simultaneously.
❖Communication Mode
Be sure to make all settings simultaneously.
 802.11 Ad-hoc
Ad-hoc
 Infrastructure
❖SSID Setting
Specifies SSID to distinguish the access point in infrastructure mode or 802.11
ad-hoc mode.
The characters that...

System Settings
60
2
❖Transmission Speed
Specifies the communication speed of the IEEE 802.11b (wireless LAN).
Auto Select
 11Mbps Fixed
 5.5Mbps Fixed
2Mbps Fixed
1Mbps Fixed
❖Restore Factory Defaults
You can return the IEEE 802.11b (wireless LAN) settings to their defaults.
No
Yes
Print List
You can check items related to the network in use.
The configuration page shows the current network settings and network infor-
mation.
APress [System Settings].
BPress [Interface Settings].
CPress [Print...

Interface Settings
61
2
DPress the {Start} key.
The configuration page is printed.
EPress [Exit].
FPress the {User Tools} key.
Note
❒You can also exit by pressing [Exit] on the User Tools main menu.
Downloaded From ManualsPrinter.com Manuals 

System Settings
62
2File Transfer
This section describes various items of [File Transfer] under [System Settings].
❖Delivery Option
Enables or disables sending stored or scanned documents to ScanRouter V2
delivery server.
On
 Main Delivery Server IPv4 Address: 000.000.000.000
 Sub Delivery Server IPv4 Address: 000.000.000.000
Off
Set this option when specifying whether or not to use ScanRouter V2. If you
do, you will have to re-register I/O devices in ScanRouter V2.
❖Capture Server IP Address
Specify...