Ricoh Aficio MP 9000 User Manual

Connecting to the Interfaces
13
1
Note
❒Select [802.11 Ad-hoc] mode when connecting Windows XP as a wireless LAN
client using Windows XP standard driver or utilities, or when not using the
infrastructure mode.
❒For details about how to make settings of wireless LAN from the control pan-
el on the machine, see IEEE 802.11b.
❒For details about how to make settings of wireless LAN from other than the
control panel on the machine, see Using Utilities to Make Settings.
❒For details about the setting items,...

Connecting the Machine
14
1
❖When using in ad-hoc mode / 802.11 ad-hoc mode
1.If the IEEE 802.11b interface unit is working, it is lit in orange.
2.If it is connected properly to the network, the LED is green when in ad-hoc
mode or 802.11 ad-hoc mode. If the LED is blinking, the machine is searching
for devices. The LED will light after a few seconds.
Print the configuration page to verify settings.
Note
❒For more information about printing a configuration page, see Print List.
Reference
p.158 “Printing...

Network Settings
15
1 Network Settings
This section describes the network settings you can change with User Tools (Sys-
tem Settings). Make settings according to functions you want to use and the in-
terface to be connected.
Important
❒These settings should be made by the systems administrator, or after consult-
ing with the systems administrator.
Settings Required to Use the Printer
This section lists the settings required for using the printer function.
Ethernet
This section lists the settings required...

Connecting the Machine
16
1
Note
❒IPv6 can be used only for the printer function.
❒In [Effective Protocol], check that the protocol you want to use is set to [Active].
❒[LAN Type] is displayed when optional wireless LAN board is installed. If Eth-
ernet and IEEE 802.11b (wireless LAN) are both connected, the selected inter-
face has priority.
Reference
p.52 “Interface Settings”
p.62 “File Transfer”
IEEE 1394 (IPv4 over 1394)
This section describes necessary set items for using Printer with IEEE 1394...

Network Settings
17
1
IEEE 802.11b (wireless LAN)
This section describes necessary set items for using Printer with IEEE 802.11b
(wireless LAN).
For details about specifying the settings, see Interface Settings and File Transfer.
Heading Setting Item Setting Requirements
interface settings/Network Machine IPv4 Address Mandatory
interface settings/Network IPv4 Gateway Address As required
interface settings/Network Machine IPv6 Address As required
interface settings/Network IPv6 Gateway Address As...

Connecting the Machine
18
1
Note
❒As to [Effective Protocol], check if the protocol to use is set as [Active].
❒[IEEE 802.11b] and [LAN Type] are displayed when optional wireless LAN inter-
face board is installed. If both Ethernet and wireless LAN (IEEE 802.11b) are
connected, the selected interface takes precedence.
Reference
p.52 “Interface Settings”
p.62 “File Transfer”
Settings Required to Use E-mail Function
This section describes necessary set items for sending e-mail.
Ethernet
This section...

Network Settings
19
1Note
❒As to [Effective Protocol], check if the protocol to use is set as [Active].
❒[LAN Type] is displayed when optional wireless LAN interface board is in-
stalled. If both ethernet and wireless LAN (IEEE 802.11b) are connected, the
selected interface takes precedence.
❒When setting [POP before SMTP] to [On], also make setting for[Reception Proto-
col] and [POP3/IMAP4 Settings].
❒When setting [POP before SMTP] to [On], check [POP3] port number in [E-mail
Communication Port]....

Connecting the Machine
20
1
Note
❒[IEEE 1394] is displayed when optional IEEE 1394 interface board is installed.
❒As to [Effective Protocol], check if the protocol to use is set as [Active].
❒When setting [POP before SMTP] to [On], also make setting for [Reception Proto-
col] and [POP3/IMAP4 Settings].
❒When setting [POP before SMTP] to [On], check [POP3] port number in [E-mail
Communication Port].
Reference
p.52 “Interface Settings”
p.62 “File Transfer”
IEEE 802.11b (wireless LAN)
This section describes...

Network Settings
21
1
Note
❒As to [Effective Protocol], check if the protocol to use is set as [Active].
❒ [LAN Type] is displayed when optional wireless LAN interface board is in-
stalled. If both ethernet and wireless LAN (IEEE 802.11b) are connected, the
selected interface takes precedence.
❒When setting [POP before SMTP] to [On], also make setting for [Reception Proto-
col] and [POP3/IMAP4 Settings].
❒When setting [POP before SMTP] to [On], check [POP3] port number in [E-mail
Communication Port]....

Connecting the Machine
22
1
Settings Required to Use Scan to Folder Function
This section describes necessary set items for sending file.
Ethernet
This section describes necessary set items for sending file with ethernet cable.
For details about specifying the settings, see Interface Settings and File Transfer.
Note
❒As to [Effective Protocol], check if the protocol to use is set as [Active].
❒[LAN Type] is displayed when optional wireless LAN interface board is in-
stalled. If both ethernet and wireless...