Projector Christie Rpmsp D180u User Manual

Section 4: Advanced Configuration and Controls
RPMSP-D132U & RPMSP-D180U User Manual User Manual4-23020-100245-03  Rev. 1  (11-2010)
These coordinate adjustments move the 3 color points closer together to establish a “shared” gamut attainable 
by all projectors in the group. Adjust only as necessary to make sure that the resulting color palette is as large 
as possible. Adjust lamp power as necessary. 
7. All screens are now color-matched. Apply the new “User” gamut to a source by selecting it in the...

4-24RPMSP-D132U & RPMSP-D180U User Manual User Manual020-100245-03  Rev. 1   (11-2010)
Section 4: Advanced Configuration and Controls
 Before You Begin
Read through the entire procedure before attempting to adjust Brightness Uniformity controls, and keep in 
mind the following list of prerequisites and guidelines: 
•
ADJUST COLORS FIRST—Adjust the primary colors as described in Section 4.14 Matching Colors In Multiple 
Screens before working with Brightness Uniformity. This makes sure that primary...

Section 4: Advanced Configuration and Controls
RPMSP-D132U & RPMSP-D180U User Manual User Manual4-25020-100245-03  Rev. 1  (11-2010)
c. Select the 13 Point test pattern for display. This pattern provides 9 screen “zones” with 13 targets. 
FOR BEST RESULTS: Rather than examining the CENTER of each zone when assessing Brightness Uniformity 
adjustments, focus on extreme EDGES as indicated in the illustration at right.
d. In either Color Adjustment menu, select a “User” color. Then:
•If you have adjusted...

4-26RPMSP-D132U & RPMSP-D180U User Manual User Manual020-100245-03  Rev. 1   (11-2010)
Section 4: Advanced Configuration and Controls
f. Make sure that overall light output remains well-matched from one screen center to the next. Where 
necessary, increase or decrease Lamp Power to recover center matches.
Step 2: Adjust Color (level of red/green/blue) in 8 Zones
NOTES: 
1) Ignore the brightness of individual zones. 
2) Ignore menu colors.
a. On each screen, compare the color temperatures in the 8 target...

Section 4: Advanced Configuration and Controls
RPMSP-D132U & RPMSP-D180U User Manual User Manual4-27020-100245-03  Rev. 1  (11-2010)
FIGURE 4-24 MATCH ZONES TO CENTER LIGHT OUTPUT
Step 4: Readjust Color Temperature (level of red/green/blue) in 8 Zones
Return to Steps 
2a & 2b and, if necessary, fine-tune the zones so that they all still exhibit a single color 
temperature.
Canceling Brightness Uniformity
If you do not want to use or apply Brightness Uniformity settings, delete the checkmark from the...

4-28RPMSP-D132U & RPMSP-D180U User Manual User Manual020-100245-03  Rev. 1   (11-2010)
Section 4: Advanced Configuration and Controls
FIGURE 4-25 EDGE BLENDING CONCEPT
For best results, use the same projector model and type throughout your display wall. Avoid high-gain screens 
whenever possible—the optical performance of such screens demands minimal image offset, thus projectors 
must be located very close to one another.
Edge blending software controls are located in the 2-page Edge Blending...

Section 4: Advanced Configuration and Controls
RPMSP-D132U & RPMSP-D180U User Manual User Manual4-29020-100245-03  Rev. 1  (11-2010)
FIGURE 4-27 “MIDPOINT” EXAMPLES
Other Functions
For convenience, the Edge Blending submenu also includes related options for enabling a specific color and/or 
test pattern, or for working with colors or the lamp. Such functions duplicate those provided elsewhere in the 
menu system.
4.15.1 Edge Blending Procedure
Before working with edge blending software functions, you...

4-30RPMSP-D132U & RPMSP-D180U User Manual User Manual020-100245-03  Rev. 1   (11-2010)
Section 4: Advanced Configuration and Controls
5. Re-adjust width (both projectors) until the overly bright band at the midpoint of the overlapping blends 
disappears or changes to very light gray. For the shared edge, use the same Blend Width setting on each 
projector. If the “best blend” appears to be between two settings, choose the wider setting for both 
projectors.
6. Check Blend. If the blended region appears...

Section 4: Advanced Configuration and Controls
RPMSP-D132U & RPMSP-D180U User Manual User Manual4-31020-100245-03  Rev. 1  (11-2010)
• To disable error messages (except for “invalid user key entry”, which can’t be hidden), select “Off”.
The 2-digit error code that corresponds to the message appears in the status display window on the electronics 
module. During normal operation the status code “0n” is displayed.
4.17.1 User Errors
Invalid User Entry
A keypad entry not recognized by the projector triggers...

4-32RPMSP-D132U & RPMSP-D180U User Manual User Manual020-100245-03  Rev. 1   (11-2010)
Section 4: Advanced Configuration and Controls
4.17.3 System Warnings / Errors
When the projector encounters a system malfunction, a System Warning or a System Error message will appear. 
These messages are accompanied by a numerical error code shown in the status display window. A system 
malfunction can be cleared with      from presentation level, but may indicate the need for service by a 
qualified service...