Projector Christie Rpmsp D180u User Manual

RPMX/RPMSP-D132U & RPMSP-D180U User ManualA-1020-100245-03 Rev. 1 (11-2010)
A Cable Connections
A serial link of RS-232 or RS-422 enables ASCII communication with the projector so that it can be controlled 
remotely from a PC or other controller. From a PC, connect a standard 9-wire RS-232 serial cable to the 
RS-232 
IN 
port. Or, for long-distance (>100 ft.) links with an RS-422-compatible PC or controller, connect RS-422 
cable to the 
RS-422 port.
A.1 Projector to Computer (RS-232)
A.2 Projector to...

A-2RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Appendix A: Cable Connections
A.3 Projector to Projector 

RPMX/RPMSP-D132U & RPMSP-D180U User ManualB-1020-100245-03 Rev. 1 (11/10)
B Dimensions & Mounting Information
B.1 Horizontal Configuration
FIGURE B-1 HORIZONTAL CONFIGURATION 

B-2RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Appendix B: Dimensions & Mounting Information
B.2 Vertical Configuration
FIGURE B-2 VERTICAL CONFIGURATION 

Appendix B: Dimensions & Mounting Information
RPMX/RPMSP-D132U & RPMSP-D180U User ManualB-3020-100245-03 Rev. 1 (11-2010)
B.3 Horizontal Configuration for SXGA 

B-4RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Appendix B: Dimensions & Mounting Information
B.4 D132U Horizontal Configuration for XGA 

RPMX/RPMSP-D132U & RPMSP-D180U User ManualC-1020-100245-03 Rev. 1 (11-2010)
C System Integration
The GPIO connector located on the input panel provides a flexible method of interfacing external I/O devices 
to the projector. There are 7 GIO pins on the 9 pin GPIO connector, which are configurable via RS-232 
commands. The other two pins are reserved for ground and power. See Table C.1 for pin identification.
The serial cable required for connecting the external device to the projector’s GPIO connector,...

C-2RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Appendix C: System Integration
Query Command
C.1.1 Real Time Event
Use the serial command RTE to specify an action that is initiated at a particular time or based on an external 
stimulus.
For General Purpose IO “G”
Example 2.
 Projector powers up when a switch on the external device is turned on.
(GIO?)Request the state and configuration of all pins
(GIO! “HHLLHLH” “OOIOOOI”) Reply with pin state and configuration
(GIO? C2)...

RPMX/RPMSP-D132U & RPMSP-D180U User ManualD-1020-100245-03 Rev. 1 (11-2010)
D Optional Input Modules
There are many optional input modules and accessories currently available for this projector. Contact your 
dealer for a complete and up-to-date listing.
NOTE: Always unplug the projector or switcher before installing or removing any optional input module.
D.1 RGB500 Input Module 38-804606-xx
The RGB500 Input Module may be installed in this projector, a Marquee Signal Switcher, or a Marquee Case/
Power...

D-2RPMX/RPMSP-D132U & RPMSP-D180U User Manual020-100245-03 Rev. 1 (11-2010)
Appendix D: Optional Input Modules
D.3 RGB400 Active Loop-Thru Input Module 38-804607-xx
The RGB400 ALT Input Module may be installed in this projector, a Marquee Signal Switcher, or a Marquee 
Case/Power Supply. The module receives analog RGB input signals from computers or other RGB source 
devices. Video inputs are 75Ω
 terminated. Video outputs provide buffered loop-through to another display 
device.
RGB400ALT Features...