Panasonic Wv Sp302 Operating Instructions Manual

61
■ Alarm image
[FTP >>]
When	"FTP	>>"	is	clicked,	the	[FTP]	tab	of	the	"Server"	
page will be displayed. (☞ Page 76)
[Alarm image FTP transmission]
Select	"On"	or	"Off"	to	determine	whether	or	not	to	
transmit the alarm image to the FTP server.
Default:	Off
[Directory name]
Enter the directory name where the alarm images are to 
be saved. 
For	example,	 enter	"/ALARM"	 to	designate	 the	directory	
"ALARM" under the root directory of the FTP server....

62
[Image compression rate upon alarm detection]
Select	"On"	or	"Off"	to	determine	whether	or	not	to	
change the image quality upon alarm detection.
On: Images will be transmitted with the image quality selected for "Image quality upon alarm detection".
Off: Does not change the image quality upon alarm  detection.
Default:	Off [Image quality upon alarm detection]
Image quality can be changed upon an alarm occur-
rence. Select the image quality from the following.
0 Super fine/1...

63
■ Alarm output terminal setup
[Alarm output trigger]
Select	"On"	or	"Off"	to	determine	whether	or	not	to	out-
put the alarm signals to the alarm output terminal when 
an alarm is detected.
Default:	Off
[Alarm output type]
Select "Latch" or "Pulse" for the alarm output terminal 
at an alarm occurrence.
Latch: When an alarm is detected, the alarm output terminal will be in the state selected for "Trigger out-
put" until the alarm occurrence indication button is...

64
[AUX (Up to 10 characters)]
Enter the name for "AUX" on the "Live" page.
Default: AUX
[Open (Up to 5 characters)]
Enter	the	name	 for	"Open"	 of	"AUX"	 on	the	 "Live"	 page.
Default:	Open
[Close (Up to 5 characters)]
Enter the name for "Close" of "AUX" on the "Live" 
page.
Default: Close
Note:
	 •	 AUX	is	a	camera	terminal	that	allows	users	to	oper -
ate	(Open/Close)	arbitrarily	from	the	"Live"	page.	
For	example,	an	operator	can...

65
[Area]
When selecting a VMD area in the screen, it will be 
numbered as area 1. (Subsequent areas will be num-
bered in the order of selection.)
[Status]
Select	"On"	or	"Off"	to	determine	whether	or	not	to	
activate each VMD area.
On: Activates the respective VMD area.
Off: Inactivates the respective VMD area.
Default:	Off
    
[Detection area]
Adjust the size of the VMD area using the slider. The 
smaller the selected value is, the higher the sensitivity 
of VMD area becomes. The...

66
■ VMD information addition
[Information addition]
Select	"On"	or	"Off"	to	determine	whether	or	not	to	add	
VMD information to image data. 
The VMD information can be searched by Panasonic network disk recorders (WJ-ND400 series). Refer to the 
operating instructions of the connected devices for fur-
ther information about the functions and settings.
Default:	Off
    
Set the VMD areas
Important:
	 •	 When	the	settings	are	being	configured	on	the	setup	menu,	sometimes	the	VMD	function...

67
Configure the settings relating to the mail notification [Notification]
Click the [Notification] tab on the "Alarm" page. (☞ Pages 22 and 23: How to display/operate the setup menu)
The settings relating to the alarm mail can be configured. It is necessary to configure the settings of the mail server 
to perform the mail notification. (☞ Page 75)
    
■ Mail notification
[Mail server >>]
When	"Mail	server	>>"	is	clicked,	the	[Mail]	tab	of	the	
"Server" page will be displayed. (☞...

68
Configure the settings relating to Panasonic alarm protocol [Notification]
Click the [Notification] tab on the "Alarm" page. (☞ Pages 22 and 23: How to display/operate the setup menu)
The settings relating to Panasonic alarm protocol can be configured in this section.
    
■ Panasonic alarm protocol notification
[Panasonic alarm protocol]
Select	"On"	or	"Off"	to	determine	whether	or	not	to	pro-
vide notification by Panasonic alarm protocol according 
to	the	settings	for	the...

69
Configure the setting relating to the image recog-
nition [Advanced func.]
The setting relating to the XML notification, destinations of information about the f\
ace detection and the settings 
relating to the face detection can be configure on the "Advanced func." page.
The "Advanced func." page has 2 tabs; the [XML notification] tab and the\
 [Face detection] tab.
Configure the settings relating to the XML notification [XML notification]
Click the [XML notification] tab on the...

70
Configure the destination settings of the face detection [XML notification]
Click the [XML notification] tab on the "Advanced func." page.
The destination settings of the face detection information can be config\
ured. The XML notification notifies the serv-
er of face detection information in XML format.
    
■  Destination setting for XML notification
[Destination 1] [Destination 2] [Destination address]
Configure the IP address or host name of the destina-
tion for XML notification of the...