Panasonic Wv Sp302 Operating Instructions Manual

41
Configure the settings relating to images and 
audio [Image/Audio]
The settings relating to JPEG, H.264 and MPEG-4 images such as the settings of image q\
uality, audio, etc. can be 
configured on this page.
The "Image/Audio" page has 3 tabs; the [JPEG/H.264] tab (or [JPEG/MPEG-4] tab), the [Im\
age/Privacy] tab and the 
[Audio] tab.
Configure the settings relating to JPEG images [JPEG/H.264]  
(or [JPEG/MPEG-4])
Click the [JPEG/H.264] tab (or [JPEG/MPEG-4] tub) on the "Image/Audio"...

42
Configure the settings relating to H.264 images [JPEG/H.264]
Click the [JPEG/H.264] tab on the "Image/Audio" page. (☞ Pages 22 and 23: How to display/operate the setup menu)
[JPEG/H.264] tab will be displayed when "H.264" is selected for "Video e\
ncoding format".
Configure	the	settings	relating	to	H.264	image	such	as	"Max	bit	rate	(per	client)",	"Image	capture	size",	"Image	
quality", etc. in this section.
Refer to page 46 and 41 for the settings...

43
[Internet mode (over HTTP)]
Select	"On"	when	transmitting	H.264	images	via	the	
Internet. It is possible to transmit H.264 images without 
changing the broadband router settings configured for 
JPEG image transmission.
On: H.264 images and audio will be transmitted using the HTTP port. Refer to page 79 for further informa-
tion about the HTTP port number settings.
Off: H.264 images and audio will be transmitted using  the UDP port.
Default:	Off
Note:
	 •	 When	"On"	is	selected,	only...

44
[Image quality]
Select the image quality of H.264 images from the fol-
lowing.
Fine(Image quality priority)/Normal/Low(Motion priority)
Default: NormalNote:
	 •	 When	"Constant	bit	rate"	is	selected	for	 "Transmission priority", this setting is available.
 
[Refresh interval]
Select an interval (I-frame interval; 0.2 - 5 seconds) to 
refresh the displayed H.264 images.
If using under a network environment with frequent 
error occurrences, shorten the refresh interval for H.264 
to...

45
Important:
	 •	 When transmitting an H.264 image via a network, 
the transmitted image sometimes may not be dis-
played	depending	on	the	settings	of	a	proxy	server	
or a firewall. In this case, refer to the network 
administrator.
	 •	 When	two	or	more	network	interface	cards	are	 installed on the PC in use, the network interface 
card(s) not used for receiving images should be 
invalidated when displaying images using the multi-
cast port.
 
  *3  It is necessary to designate the unicast port number...

46
Configure the settings relating to MPEG-4 images [JPEG/MPEG-4]
Click the [JPEG/MPEG-4] tab on the "Image/Audio" page. (☞ Pages 22 and 23: How to display/operate the setup 
menu)
The [JPEG/MPEG-4] tab will be displayed when "MPEG-4" is selected for "V\
ideo encoding format". (☞ Page 42)
Configure	the	settings	relating	to	MPEG-4	image	such	as	"Max	bit	rate	(per	client)*",	"Image	capture	size",	"Image	
quality", etc. in this section.
Refer to page 42 and 41...

47
Note:
	 •	 When	"On"	is	selected,	only	"Unicast	port	(AUTO)"	 will be available for "Transmission type". 
	 •	 When	"On"	is	selected,	it	may	take	seconds	to	start	 displaying MPEG-4 images.
	 •	 When	"On"	is	selected,	MPEG-4	images	may	not	be	 displayed depending on the number of the concur-
rent access users and audio data availability, etc. 
	 •	 When	"On"	is	selected,	only	IPv4	access	is	avail- able. 
	 •	 When	"On"	is	selected	for	either...

48
	 	 When	it	is	unnecessary	to	fix	the	port	number	for	MPEG-4 image transmission such as when using in 
a particular LAN environment, it is recommended to 
select	"Unicast	port	(AUTO)".
Unicast port (MANUAL): Up to 14 users can access a  single camera concurrently. It is necessary to select 
"Unicast port1(Image)" and "Unicast port2 (Audio)" 
manually to transmit images and audio from the 
camera.
	 	 It	is	possible	to	fix	the	port	number	of	the	router	 used for MPEG-4 image...

49
Configure the settings relating to images, focus and the privacy zone 
[Image/Privacy]
Click the [Image/Privacy] tab on the "Image/Audio" page. (☞ Pages 22 and 23: How to display/operate the setup menu)
When	the	[Setup	>>]	button	of	each	setting	item	is	clicked,	the	detailed	settings	menu	will	be	displayed	in	a	newly	
opened window. The detailed settings can be configured while monitoring images displayed on the [Image/Privacy] 
tab.
The following are descriptions of how to configure the...

50
Configure the settings relating to image quality ("Image adjust" setup menu)
Click	the	[Setup	>>]	button	of	"Image	adjust"	on	the	[Image/Privacy] tab of the "Image/Audio" page. (☞ Page 49)
The settings relating to image quality can be configured with the setup menu displayed in a newly displayed win-
dow. When the values are changed, the changed values will be applied to the currently displayed image on the 
[Image/Privacy] tab.Important:
	 •	 Image	adjustment	functions	are...