Panasonic Wv Ns202 Operating Instructions Manual

51
Step 5
Select the detection sensitivity from the following. The
selected detection sensitivity will be applied to all the
VMD areas. 
High/Middle/Low
Default:MiddleStep 6
Click the [SET] button after completing the settings.
Important:
The setting will not be applied unless the [SET] but-
ton is clicked.
Delete the VMD area set for the designated preset position
Step 1
Display the VMD area setup window of the preset posi-
tion number whose VMD area is to be deleted. 
(page 50)
Step 2
Click the...

52
Configure the settings relating to the mail notification [Notification]
Click the [Notification] tab on the Alarm setup page. (page 15)
E-mail notification setup
The settings relating to the alarm mail can be configured in this section. To provide notification of an alarm occur-
rence by e-mail, it is necessary to configure the settings of the mail server. (page 56)
[To E-mail server setup]
When To E-mail server setup is clicked, the [Mail] tab
of the Server setup page will be displayed. 
(page...

53
Configure the settings relating to Panasonic alarm protocol
Click the [Notification] tab on the Alarm setup page. (page 15)
Panasonic alarm protocol setup
The settings relating to Panasonic alarm protocol can be configured in this section. 
[Panasonic alarm protocol]
Select ON or OFF to determine whether or not to
provide notification of an alarm occurrence by
Panasonic alarm protocol when an alarm is detected. 
Default:OFF
Note:
When ON is selected, notification of the alarm
occurrence will be...

54
Configure the settings relating to the authentication
[Authentication setup]
The settings relating to the authentication such as users and PCs restrictions for accessing the camera can be con-
figured on this page. 
The Authentication setup page has 2 tabs of the [User] tab and the [Host] tab.
Configure the settings relating to the user authentication [User]
Click the [User] tab on the Authentication setup page. (page 15)
The settings relating to the user authentication can be configured on this...

55
Configure the settings relating to the host authentication [Host]
Click the [Host] tab on the Authentication setup page. (page 15)
The settings to restrict PCs (IP address) from accessing the camera can be configured on this page.
[Host authentication]
Select ON or OFF to determine whether or not to
authenticate the host.
Default:OFF
Important:
Before configuring the host authentication, it is nec-
essary to register IP addresses of the PCs to be
allowed to access the camera and determine their...

56
Configure the settings of the servers [Server setup]
The settings relating to the mail server and the FTP server can be configured on this page. 
The Server setup page has 2 tabs; the [Mail] tab and the [FTP] tab.
Configure the settings relating to the mail server [Mail]
Click the [Mail] tab on the Server setup page. (page 15)
The settings relating to the mail server used to send the alarm mail can be configured on this page. 
[SMTP server address]*
Enter the IP address or the host name of the SMTP...

57
Configure the settings relating to the FTP server [FTP]
Click the [FTP] tab on the Server setup page. (page 15)
The settings relating to the FTP server used to transmit the alarm images can be configured on this page. 
[FTP server address]
Enter the IP address or the host name of the FTP serv-
er. 
Number of characters for the FTP server address:
1 - 128 characters
Important:
When entering the host name for FTP server
address, it is necessary to configure the DNS set-
tings on the [Network] tab of...

58
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management
Protocol) can be configured on this page. 
The Network setup page has 4 tabs; the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab. 
Configure the network settings [Network]
Click the [Network] tab on the Network setup page. (page 15)
The following information is required to configure the network settings. 
Contact the network...

59
[Default gateway]
When not using the DHCP function, enter the default
gateway of the camera. 
Default:192.168.0.1

0.*.*.*
*.*.*.0
255.*.*.*
*.*.*.255
127.0.0.1
Class D addresses (224.0.0.0 - 239.255.255.255)
Class E addresses (240.0.0.0 - 255.255.255.255)
Note:
These IP addresses for the default gateway are
unavailable even when using the DHCP function.
Refer to the network administrator for further infor-
mation about the settings of the DHCP server. 
[HTTP port]
Assign the port numbers...

60
Notes:
•The port forwarding function changes a global IP address to a private IP address, and Static IP masquerade
and Network Address Translation (NAT) have this function. This function is to be set in a router.
•To access the camera via the Internet by connecting the camera to a broadband router, it is necessary to assign
a respective port number for each camera and address translation by using the port forwarding function. For fur-
ther information, refer to the operating instructions of the...