Panasonic Wv Ns202 Operating Instructions Manual

41
[Audio output volume (PC to Camera)]
Select a volume level on the camera to hear audio
transmitted from the PC.
Low/Middle/High
Default:Middle
[Audio output interval (PC to Camera)]
Select an interval for audio transmission from the follow-
ing.
160 msec/320 msec/640 msec/1 280 msec
Default:640 msec
Notes:
• When a shorter interval is selected, the delay time
will be shorter. When a longer interval is selected,
audio interruption may be diminished even though
the delay time will be longer.
Select the...

42
Configures the multi-screen settings [Multi-screen setup]
The cameras to be used for the multi-screen display can be registered on this page. 
Refer to page 9 for descriptions of how to display images on a multi-screen.
The following cameras are applicable for the multi-screen display. (As of October, 2006)
WV-NS202, WV-NP240 series, WV-NP1000 series, WV-NW470S series, WV-NP472, WV-NS320 series
[IP address]
Enter the IP address or the host name of the camera to
be used for the multi-screen. 4 cameras...

43
Configure the alarm settings [Alarm setup]
The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm
occurrence notification, and the VMD area settings can be configured on this page. 
The Alarm setup page has 3 tabs; the [Alarm] tab, the [VMD area] tab and the [Notification] tab.
Configure the settings relating to the alarm [Alarm]
Click the [Alarm] tab on the Alarm setup page. (page 15)
Alarm setup
The settings relating to the alarm can be...

44
Configure the settings relating to the camera action at an alarm occurrence
Click the [Alarm] tab on the Alarm setup page. (page 15)
Camera motion on alarm
The settings relating to the camera action at an alarm occurrence can be configured in this section. Refer to pages
43, 46 and 47 for further information about the settings relating to the alarm, the alarm image and the alarm output
terminal.
[Terminal alarm 1]
Select an action to be taken when a terminal alarm 1 is
detected from the following....

45
Auto track:When a VMD alarm is detected, the cam-
era will move to the home position and start the auto
tracking.
Default:OFF
[Command alarm]
Select an action to be taken when a command alarm is
detected from the following.
OFF:Does not take any action even when a command
alarm is detected. 
1-64:When the registered preset position is selected,
the camera will move to the selected preset position
when a command alarm is detected.
Auto track:When a command alarm is detected, the
camera will move to the...

46
Configure the settings relating to the alarm image
Click the [Alarm] tab on the Alarm setup page. (page 15)
Alarm image setup
The settings relating to the alarm image to be transmitted to an FTP server can be configured in this section. The
alarm image will be transmitted to an FTP server. To transmit alarm images to an FTP server, it is necessary to con-
figure the settings in advance. (page 57)
Refer to pages 43, 44 and 47 for further information about the settings relating to the alarm, the...

47
Configure the settings relating to the alarm out connector
Click the [Alarm] tab on the Alarm setup page. (page 15)
Alarm output terminal setup
The settings relating to the alarm out connector can be configured in this section. The settings for the alarm output
terminal can be configured only when Alarm output is selected for Terminal alarm 2 of Alarm setup. Refer to
pages 43, 44 and 46 for further information about the settings relating to the alarm, the camera action at an alarm
occurrence and the...

48
Set the VMD areas [VMD area]
Click the [VMD area] tab on the Alarm setup page. (page 15)
The video motion detection areas can be set on this page. 
The VMD areas can be set for each preset position (up to 64 areas). When motion is detected in the set area, the
alarm action will be performed. The camera can be configured to take an alarm action even when the camera is not
at the preset position.
Important:
•Areas used for the time and date display of OSD position (page 20) cannot be used for the VMD...

Configure to detect motion in areas without the preset positions
Configure whether or not to detect motion when the camera is not at the preset position by setting the detection sen-
sitivity. The sensitivity can be set by configuring VMD area setting except Preset position. When determining
whether to detect motion even when the camera is not at the preset position, all areas except areas used for the
time and date display of OSD position will be subject to the detection. The VMD area setting is...

50
Step 1
Select a preset position number to which the VMD area
is to be set from Preset position select of VMD area
setting for Preset position. 
Step 2
Click the [Setup] button.
→The VMD area setup window for the selected preset
position number will be displayed.
Step 3
Set the video motion detection area by dragging the
mouse on the screen. 
When the [All areas] button is clicked, the whole area
will become the VMD area and set as area 1 (white). 
→The designated area will become the VMD area and
the...