Panasonic Wv Np1000 Operating Instructions Manual

61
Step 1
Select ON for EL-ZOOM on the CAMERA SETUP
page.
→The EL-ZOOM page will be displayed.
Step 2
Move the cursor onto ZOOM and press the [SET] but-
ton.
→Images to which zooming can be applied will be dis-
played.
Step 3
Adjust zooming level pressing the [Up] and [Down] but-
tons. After completing the adjustment, press the [SET]
button.
→The EL-ZOOM page will be displayed.
Step 4
Move the cursor onto PAN/TILT and press the [SET]
button.
→Images to which panning/tilting can be applied will
be...

62
Correct image defects (blemishes) such as scratches
Image defects (blemishes) such as scratches can be corrected in the fo\
llowing method.
Step 1
Press the [SET] button after moving the cursor onto
PIX OFF on the SPECIAL SETUP page. → The PIX OFF page will be displayed.
Step 2
Press the [SET] button after selecting a number (1  – 16)
to be registered as a blemish compensation point. → The blemish compensation point setting window will
be displayed.
Step 3
Press the [SET] button after moving the cross...

63
About the Displayed System Log
Error indications relating to SMTP
Category
POP3 server error
SMTP server error
Internal errorAuthentication error
Cannot connect to POP3 server
Authentication error
Other error Connection error to DNS server
Cannot connect to SMTP server.Entered user name or password may be
incorrect. Check if the mail settings are con-
figured correctly.
•The IP address of the server may be
incorrect. Check if the IP address of the
server is configured correctly.
•The POP3 server may...

64
Category
Connection error
Connection error
Time adjustment 
synchronizing with NTP
succeeded. Internal error Internal errorCannot connect to DDNS server.
Cannot connect to NTP server.
Succeeded in the update. (NTP) Other error User name and password isnt correct.
IP address updated failed.
Other error•The designated IP address of the DDNS
may be incorrect. Check if the DDNS set-
tings are configured correctly. 
•The DDNS server may be down. Ask the
network administrator.
•The IP address of the server...

65
•Are the set IP addresses valid?
•Is the LAN cable (category 5) is firmly connected to the
network connector on the rear of the camera?
Troubleshooting
Before asking for repairs, check the symptoms with the following table
Contact your dealer if a problem cannot be solved even after checking and trying the solution or if the problem is not
described below.
•Is the same IP address provided to other devices?
Are there contradictions between the address and the
network subnet to be accessed?

Are the IP...

•Is the SD memory card formatted?
•Isn’t the write protect switch set to LOCK?
When the write protect switch is set to LOCK, avail-
able size/total size indication of the SD memory card
will be **********KB/**********KB.
•Depending on the version of your browser, there might
be difficulties refreshing the picture and operating the
camera.
It is recommended to use Internet Explorer 6.0 SP2.
•Is the SD memory card inserted correctly?
66
•Aren’t there dusts or dirt on the lens?
Check if there are dust or...

67
Flicker occurs. (The screen
flickers.)
Images from analog output
are not smoothly displayed.
Images cannot be saved on
the SD memory card.
49 • Is the camera used under fluorescent lamps operating
at 60 Hz?
By setting the shutter speed to 1/60 or 1/120, flicker
caused by fluorescent lamps can be diminished. • Check if the SD memory card is inserted firmly?
Replace the SD memory card with a new one.
(Generally, SD memory cards have a limited number
of times to rewrite.) Contact your dealer if this...

68
•This may occur due to the display adapter and driver
combination.
When this occurred, update the driver of the display
adapter to the latest version first.
If updating the driver does not solve the problem,
adjust the hardware acceleration as follows.
1. Right-click on the desktop and select Properties
from the displayed pop-up menu.
2. Select Settings from Display Properties, and
then click the [Advanced] button.
3. Click the [Troubleshoot] tab and disable the
DirectDraw acceleration by adjusting...

69
When using a PC on which Windows XP Service Pack2 (SP2) is installed
The following may occur during operation when using a PC on which Windows XP Service Pack2 (SP2) is installed.
Follow the instructions below when the following occurred. By performing the following solutions, other applications
and the security level may not be affected. 
The Information Bar expressed in the following symptom and solutions will be displayed just below the address bar
only when there is information to communicate....

Matsushita Electric Industrial Co., Ltd.
Osaka, Japan
http://www.panasonic.co.jp/global/
© 2005 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. N1205-0       3TR004271AAA Printed in Japan