Panasonic Wv Np1000 Operating Instructions Manual

21
Configure the settings relating to the NTP server [NTP]
Click the [NTP] tab on the Basic setup page. (page 19)
The settings relating to the NTP server such as the NTP server address, port number, etc. can be configured on this
page. 
[Time adjustment]
Select the time adjustment method from the following.
Time adjusted by the selected method will be used as
the standard time of the camera. 
Manual setup:Time set on the [Basic] tab on the
Basic setup page will be used as the standard time
of the...

22
[About SD memory card]
Select Use or Not use to determine whether or not to
use the SD memory card.
Important:
•Before removing the SD memory card from the cam-
era, it is necessary to select Not use first.
•After inserting the SD memory card, it is necessary
to select Use to use the SD memory card. 
[Information about SD memory card]
Available size and the total size of the SD memory card
will be displayed. 
Depending on the state of the SD memory card, the size
indications will differ as follows....

23
Configure the settings relating to images and audio [Camera
setup]
The settings relating images and audio such as brightness and image quality of JPEG/MPEG-4 can configured on
this page. 
The Camera setup page has 3 tabs of the [JPEG/MPEG-4] tab, the [Camera] tab and the [Audio] tab. 
Configure the settings relating to JPEG image [JPEG/MPEG-4]
Click the [JPEG/MPEG-4] tab on the Camera setup page.
Configure the settings such as Refresh interval (JPEG), Image capture size and Image quality on this...

24
Configure the settings relating to MPEG-4 image [JPEG/MPEG-4]
Click the [JPEG/MPEG-4] tab on the Camera setup page. (page 23)
Configure the settings such as Max bit rate (per 1 client), Image capture size and Image quality on this page.
Refer to page 23 for further information about the settings relating to JPEG images.
[MPEG-4 transmission]
Select ON or OFF to determine whether or not to
transmit MPEG-4 images.
ON:Transmits MPEG-4 images.
OFF:Does not transmit MPEG-4 images.
Default:ON
[Max bit rate...

25
Configure the camera settings such as image quality and brightness, etc.
[Camera]
Click the [Camera] tab on the Camera setup page. (page 23)
The following are descriptions of how to configure the settings relating to image quality and brightness, etc. Refer to
the operating instructions (book) for further information about the setup items (camera setup page). Refer to page 49
for descriptions of how to operate the setup items (camera setup page).
Note:
The Camera setup page on the [Camera] tab can be...

26
Configure the settings relating to audio [Audio]
Click the [Audio] tab on the Camera setup page. (page 23)
The settings relating to audio can be configured on this page. 
[Mic mode*]
Select ON or OFF to determine whether to turn on or
off audio on a PC.
ON:Transmits audio from the camera to the PC. Audio
can be heard with images on the PC. Images and
audio will not be synchronized. 
OFF:Does not transmit audio from the camera to the
PC. Therefore, no settings and controls relating
audio will be...

27
Configures the multi-screen settings [Multi-screen setup]
The cameras to be used for the multi-screen display can be registered on this page. 
Refer to page 9 for descriptions of how to display images on a multi-screen.
[IP Address]
Enter the IP address or the host name of the camera to
be used for the multi-screen. 4 cameras can be regis-
tered as a group and up to 2 groups (8 cameras) can be
registered. 
When the HTTP port number for the camera had
been changed, enter as follows:
IP address of the...

28
Configure the alarm settings [Alarm setup]
The settings relating to alarm occurrences such as settings for the alarm action at an alarm occurrence, the alarm
occurrence notification, and the VMD area settings can be configured on this page. 
The Alarm setup page has 3 tabs of the [Alarm] tab, the [VMD area] tab and the [Notification] tab.
Configure the settings relating to the alarm action [Alarm]
Click the [Alarm] tab on the Alarm setup page.
The settings relating to the alarm action can be...

29
[Alarm image FTP transmission]
Select ON or OFF to determine whether or not to
transmit the alarm image to the FTP server.
Default:OFF
[Directory]
Enter the directory name where the alarm images are to
be saved. 
Number of characters for the directory name:
0 - 256 characters
[File name]
Enter the file name used for the alarm image to be
transmitted to the FTP server. The file name will be as
follows. 
[Entered file name + Time and date (year/month/day/
hour/minute/second)] + Serial number
Number of...

30
Configure the settings relating to the alarm out connector [Alarm output setup]
Click the [Alarm] tab on the Alarm setup page. (page 28)
The settings relating to the alarm out connector can be configured on this page. Refer to pages 29 and 30 for further
information about the settings relating to the alarm image and the alarm out connector.
[Alarm output setup]
Select ON or OFF to determine whether or not to
output the alarm signals to the alarm out connector
when an alarm is detected.
Default:OFF...