Panasonic Wv Np1000 Operating Instructions Manual
Here you can view all the pages of manual Panasonic Wv Np1000 Operating Instructions Manual. The Panasonic manuals for Camera are available online for free. You can easily download all the documents as PDF.
Page 31
![Page 31
31
Set the VMD areas [VMD area]
Click the [VMD area] tab on the Alarm setup page. (page 28)
The video motion detection areas can be set on this page.
When a motion is detected in the set area, the alarm action will be perf\
ormed.
Note:
It will take around 5 minutes to start detection after the power is turn\
ed on.
Set the VMD areas
Step 1
Set the video motion detection area by dragging the
mouse on the screen. When the [All areas] button is
clicked, the whole area will become the VMD area, and
1...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-30.png "Page 31
31
Set the VMD areas [VMD area]
Click the [VMD area] tab on the Alarm setup page. (page 28)
The video motion detection areas can be set on this page.
When a motion is detected in the set area, the alarm action will be perf\
ormed.
Note:
It will take around 5 minutes to start detection after the power is turn\
ed on.
Set the VMD areas
Step 1
Set the video motion detection area by dragging the
mouse on the screen. When the [All areas] button is
clicked, the whole area will become the VMD area, and
1...")
31 Set the VMD areas [VMD area] Click the [VMD area] tab on the Alarm setup page. (page 28) The video motion detection areas can be set on this page. When a motion is detected in the set area, the alarm action will be perf\ ormed. Note: It will take around 5 minutes to start detection after the power is turn\ ed on. Set the VMD areas Step 1 Set the video motion detection area by dragging the mouse on the screen. When the [All areas] button is clicked, the whole area will become the VMD area, and 1...
Page 32
![Page 32
32
Step 6
Select ON or OFF for Light detection control.
When ON is selected, detection errors caused by turn-
ing lighting on/off can be diminished.
Notes:
•Complete prevention of detection error is not guar-
anteed even if using this function.
•When ON is selected, performance of the motion
detection may be lower.
Step 7
Click the [SET] button after completing the settings.
Important:
The setting will not be applied unless the [SET] but-
ton is clicked.
Delete the set VMD area
Step 1
Click the [DEL]...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-31.png "Page 32
32
Step 6
Select ON or OFF for Light detection control.
When ON is selected, detection errors caused by turn-
ing lighting on/off can be diminished.
Notes:
•Complete prevention of detection error is not guar-
anteed even if using this function.
•When ON is selected, performance of the motion
detection may be lower.
Step 7
Click the [SET] button after completing the settings.
Important:
The setting will not be applied unless the [SET] but-
ton is clicked.
Delete the set VMD area
Step 1
Click the [DEL]...")
32 Step 6 Select ON or OFF for Light detection control. When ON is selected, detection errors caused by turn- ing lighting on/off can be diminished. Notes: •Complete prevention of detection error is not guar- anteed even if using this function. •When ON is selected, performance of the motion detection may be lower. Step 7 Click the [SET] button after completing the settings. Important: The setting will not be applied unless the [SET] but- ton is clicked. Delete the set VMD area Step 1 Click the [DEL]...
Page 33
![Page 33
33
Configure the settings relating to the mail notification [Notification]
Click the [Notification] tab on the Alarm setup page. (page 28)
The settings relating to the alarm mail can be configured on this page. To notify of an alarm occurrence by e-mail, it
is necessary to configure the settings of the mail server. (page 37)
[E-mail notification]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by e-mail at an alarm
occurrence.
Default:OFF
[Address]
Enter the destination...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-32.png "Page 33
33
Configure the settings relating to the mail notification [Notification]
Click the [Notification] tab on the Alarm setup page. (page 28)
The settings relating to the alarm mail can be configured on this page. To notify of an alarm occurrence by e-mail, it
is necessary to configure the settings of the mail server. (page 37)
[E-mail notification]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by e-mail at an alarm
occurrence.
Default:OFF
[Address]
Enter the destination...")
33 Configure the settings relating to the mail notification [Notification] Click the [Notification] tab on the Alarm setup page. (page 28) The settings relating to the alarm mail can be configured on this page. To notify of an alarm occurrence by e-mail, it is necessary to configure the settings of the mail server. (page 37) [E-mail notification] Select ON or OFF to determine whether or not to notify of an alarm occurrence by e-mail at an alarm occurrence. Default:OFF [Address] Enter the destination...
Page 34
![Page 34
34
Configure the settings relating to Panasonic alarm protocol
[Panasonic alarm protocol setup]
Click the [Notification] tab on the Alarm setup page. (page 28)
The settings relating to Panasonic alarm protocol can be configured on this page.
[Panasonic alarm protocol]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by Panasonic alarm proto-
col when an alarm is detected.
Default:OFF
[Destination port]
Select a destination port of the Panasonic alarm proto-
col from the...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-33.png "Page 34
34
Configure the settings relating to Panasonic alarm protocol
[Panasonic alarm protocol setup]
Click the [Notification] tab on the Alarm setup page. (page 28)
The settings relating to Panasonic alarm protocol can be configured on this page.
[Panasonic alarm protocol]
Select ON or OFF to determine whether or not to
notify of an alarm occurrence by Panasonic alarm proto-
col when an alarm is detected.
Default:OFF
[Destination port]
Select a destination port of the Panasonic alarm proto-
col from the...")
34 Configure the settings relating to Panasonic alarm protocol [Panasonic alarm protocol setup] Click the [Notification] tab on the Alarm setup page. (page 28) The settings relating to Panasonic alarm protocol can be configured on this page. [Panasonic alarm protocol] Select ON or OFF to determine whether or not to notify of an alarm occurrence by Panasonic alarm proto- col when an alarm is detected. Default:OFF [Destination port] Select a destination port of the Panasonic alarm proto- col from the...
Page 35
![Page 35
35
Configure the settings relating to the authentication
[Authentication setup]
The settings relating to the authentication such as users and PCs (IP addresses) restrictions for accessing the cam-
era can be configured on the Authentication setup page.
The Authentication setup page has 2 tabs of the [User] tab and the [Host] tab.
Configure the settings relating to the user authentication [User]
Click the [User] tab on the Authentication setup page.
The settings relating to the user authentication can be...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-34.png "Page 35
35
Configure the settings relating to the authentication
[Authentication setup]
The settings relating to the authentication such as users and PCs (IP addresses) restrictions for accessing the cam-
era can be configured on the Authentication setup page.
The Authentication setup page has 2 tabs of the [User] tab and the [Host] tab.
Configure the settings relating to the user authentication [User]
Click the [User] tab on the Authentication setup page.
The settings relating to the user authentication can be...")
35 Configure the settings relating to the authentication [Authentication setup] The settings relating to the authentication such as users and PCs (IP addresses) restrictions for accessing the cam- era can be configured on the Authentication setup page. The Authentication setup page has 2 tabs of the [User] tab and the [Host] tab. Configure the settings relating to the user authentication [User] Click the [User] tab on the Authentication setup page. The settings relating to the user authentication can be...
Page 36
![Page 36
36
Configure the settings relating to the host authentication [Host]
Click the [Host] tab on the Authentication setup page. (page 35)
The settings to restrict PCs (IP address) to access the camera can be configured on this page.
[Host authentication]
Select ON or OFF to determine whether or not to
authenticate the host.
Default:OFF
Important:
Before configuring the host authentication, it is nec-
essary to register IP addresses of the PCs to be
allowed to access the camera and determine their
access...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-35.png "Page 36
36
Configure the settings relating to the host authentication [Host]
Click the [Host] tab on the Authentication setup page. (page 35)
The settings to restrict PCs (IP address) to access the camera can be configured on this page.
[Host authentication]
Select ON or OFF to determine whether or not to
authenticate the host.
Default:OFF
Important:
Before configuring the host authentication, it is nec-
essary to register IP addresses of the PCs to be
allowed to access the camera and determine their
access...")
36 Configure the settings relating to the host authentication [Host] Click the [Host] tab on the Authentication setup page. (page 35) The settings to restrict PCs (IP address) to access the camera can be configured on this page. [Host authentication] Select ON or OFF to determine whether or not to authenticate the host. Default:OFF Important: Before configuring the host authentication, it is nec- essary to register IP addresses of the PCs to be allowed to access the camera and determine their access...
Page 37
![Page 37
37
Configure the settings of the servers [Server setup]
The settings relating to the mail server and the FTP server can be configured on this page.
The Server setup page has 2 tabs of the [Mail] tab and the [FTP] tab.
Configure the settings relating to the mail server [Mail]
Click the [Mail] tab on the Server setup page.
The settings relating to the mail server used to send the alarm mail can be configured on this page.
[SMTP server address]*
Enter the IP address or the host name of the SMTP
server...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-36.png "Page 37
37
Configure the settings of the servers [Server setup]
The settings relating to the mail server and the FTP server can be configured on this page.
The Server setup page has 2 tabs of the [Mail] tab and the [FTP] tab.
Configure the settings relating to the mail server [Mail]
Click the [Mail] tab on the Server setup page.
The settings relating to the mail server used to send the alarm mail can be configured on this page.
[SMTP server address]*
Enter the IP address or the host name of the SMTP
server...")
37 Configure the settings of the servers [Server setup] The settings relating to the mail server and the FTP server can be configured on this page. The Server setup page has 2 tabs of the [Mail] tab and the [FTP] tab. Configure the settings relating to the mail server [Mail] Click the [Mail] tab on the Server setup page. The settings relating to the mail server used to send the alarm mail can be configured on this page. [SMTP server address]* Enter the IP address or the host name of the SMTP server...
Page 38
![Page 38
38
Configure the settings relating to the FTP server [FTP]
Click the [FTP] tab on the Server setup page. (page 37)
The settings relating to the FTP server used to transmit the alarm images can be configured on this page.
[FTP server address]
Enter the IP address or the host name of the FTP serv-
er.
Number of characters for the FTP server address:
1 - 128 characters
Important:
When entering the host name for FTP server
address, it is necessary to configure the DNS set-
tings on the [Network] tab of...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-37.png "Page 38
38
Configure the settings relating to the FTP server [FTP]
Click the [FTP] tab on the Server setup page. (page 37)
The settings relating to the FTP server used to transmit the alarm images can be configured on this page.
[FTP server address]
Enter the IP address or the host name of the FTP serv-
er.
Number of characters for the FTP server address:
1 - 128 characters
Important:
When entering the host name for FTP server
address, it is necessary to configure the DNS set-
tings on the [Network] tab of...")
38 Configure the settings relating to the FTP server [FTP] Click the [FTP] tab on the Server setup page. (page 37) The settings relating to the FTP server used to transmit the alarm images can be configured on this page. [FTP server address] Enter the IP address or the host name of the FTP serv- er. Number of characters for the FTP server address: 1 - 128 characters Important: When entering the host name for FTP server address, it is necessary to configure the DNS set- tings on the [Network] tab of...
Page 39
![Page 39
39
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management
Protocol) can be configured on this page.
The Network setup page has 3 tabs of the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab.
Configure the network settings [Network]
Click the [Network] tab on the Network setup page.
The following information is required to configure the network settings.
Contact the network administrator or...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-38.png "Page 39
39
Configuring the network settings [Network setup]
The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management
Protocol) can be configured on this page.
The Network setup page has 3 tabs of the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab.
Configure the network settings [Network]
Click the [Network] tab on the Network setup page.
The following information is required to configure the network settings.
Contact the network administrator or...")
39 Configuring the network settings [Network setup] The network settings and the settings relating to DDNS (Dynamic DNS) and SNMP (Simple Network management Protocol) can be configured on this page. The Network setup page has 3 tabs of the [Network] tab, the [DDNS] tab, the [SNMP] tab and the [FTP] tab. Configure the network settings [Network] Click the [Network] tab on the Network setup page. The following information is required to configure the network settings. Contact the network administrator or...
Page 40
![Page 40
40
[HTTP port]
Assign the port numbers independently.
The following port numbers are unavailable since they
are already in use.
Available port number:1 - 65535
Default:80
20, 21, 23, 25, 42, 53, 67, 68, 69, 110, 123, 161,
162, 995, 10669, 10670
[DNS]
Select AUTO or MANUAL to determine whether or
not to use the DNS. When MANUAL is selected, it is
necessary to configure the settings for the DNS.
When using the DHCP function, it is possible to obtain
the DNS address automatically by selecting AUTO.
Refer...](http://img.usermanuals.tech/thumb/58/68504/w300_wv-np1000_en_om_d-39.png "Page 40
40
[HTTP port]
Assign the port numbers independently.
The following port numbers are unavailable since they
are already in use.
Available port number:1 - 65535
Default:80
20, 21, 23, 25, 42, 53, 67, 68, 69, 110, 123, 161,
162, 995, 10669, 10670
[DNS]
Select AUTO or MANUAL to determine whether or
not to use the DNS. When MANUAL is selected, it is
necessary to configure the settings for the DNS.
When using the DHCP function, it is possible to obtain
the DNS address automatically by selecting AUTO.
Refer...")
40 [HTTP port] Assign the port numbers independently. The following port numbers are unavailable since they are already in use. Available port number:1 - 65535 Default:80 20, 21, 23, 25, 42, 53, 67, 68, 69, 110, 123, 161, 162, 995, 10669, 10670 [DNS] Select AUTO or MANUAL to determine whether or not to use the DNS. When MANUAL is selected, it is necessary to configure the settings for the DNS. When using the DHCP function, it is possible to obtain the DNS address automatically by selecting AUTO. Refer...