Panasonic Wv Nm100 Operating Instructions Manual

41
Operate while monitoring the picture.
(The screenshot below shows when a multi-screen is used.)
The Save Picture window appears.
Screenshot 2
Screenshot 1
Saving the Currently Monitored Picture on the PC
Save the still picture currently monitored as a file on the PC.
You can save the picture either as single screen or multi-screen (quad screen).
You can save only still pictures (JPEG). Saving motion pictures (MPEG-4) is not available.
! Important
Move the cursor on the picture to save and click
the...

42
DETECTING MOTION IN THE MONITORED AREA
When motion is detected in the monitored area, Alarm appears on the monitor screen. Simultaneously, you can
save the picture of the alarmed area and send an alarm mail by e-mail (motion detector function).
You can also automatically transfer the saved image to the server.
To activate these functions, complete the setting of the Alarm page or the FTP client page in advance.
•In case a sensor is connected to the alarm connector of the camera, the functions above...

43
• Inform by sending e-mails.
You can send an alarm mail that notifies an alarm has occurred and the alarm date and time to a designated e-mail
address registered in advance.
You can also attach a picture to that mail.
You can register up to four e-mail addresses to which this alarm mail will be sent.
Contents of the alarm mail:
“In WV-NM100, Alarm was occurred.
Date: XXXX.XX.XX.XX:XX:XX
URL: http:// xxx.yyy.zzz.nnn/alarm/image/*****.jpg”
(XXXX.XX.XX.XX:XX:XX is the date: year-month-day hour:min:sec)...

The Operation mode page of Advanced setup
appears.
The Alarm page appears.
Screenshot 3
Screenshot 2
44
DETECTING MOTION IN THE MONITORED AREA
Set the items on the Alarm page.
Refer to the next page for details about each
item.
Click the [SET] button after completing the set-
ting.
STEP4
STEP3
Click the [Alarm&Transmission] button.
STEP2 

45
[E-mail notice setup]
E-mail notice
Select ON or OFF to set whether to notice by e-mail
or not when an alarm occurs.
SMTP server address
Enter the SMTP server address of the sender
Authentication
Select SMTP, POP3 or None for the authentica-
tion.
SMTP:Authentication by the SMTP server
POP3:Authentication by POP before SMTP
None: No authentication
POP3 server address
Enter the POP3 server address when POP3 is
selected for Authentication.
User name
Enter the name of the sender, up to 64 characters....

46
DETECTING MOTION IN THE MONITORED AREA
Setting of the Motion Detection Area
Set the area where motion has to be detected. You can set up to four areas. The setting can be made on the VMD
area page of Alarm&Transmission.
Begin the operation from the Basic setup page.
Refer to page 24 and 25 to display the Basic setup page.
The Operation mode page of Advanced setup appears.
Screenshot 2
Screenshot 1
Click the [Advanced setup] button.
STEP1
Click the [Alarm&Transmission] button.
STEP2 

47
The Alarm page appears.
The VMD area page appears.
Screenshot 4
Screenshot 3
Click the [VMD area] tab.
STEP3
Select the desired area number to be registered
by clicking the [Area 1] - [Area 4] radio buttons.
Up to four areas can be designated.
Designate the area for the selected area num-
ber by clicking on the picture.
To designate the area, click the top left corner
and the bottom right corner of the area you wish
to set.
To cancel the designated area, select the area
number to be canceled from the...

•Though the Alarm log list displays up to 100 alarm logs,
only 60 pictures can be stored at the maximum.
•Depending on the traffic of the network, a drop frame may
occur while monitoring alarm pictures. If this occurs, click
the [B] button or the [A] button to monitor each frame.
•Display the saved still pictures (JPEG) using the web
browser. Some image-editing software cannot open or
display the saved still pictures.
! Important
48
DETECTING MOTION IN THE MONITORED AREA
Viewing the Picture Stored in the...

49
TRANSFERRING PICTURES TO THE SERVER
Transfer the pictures stored in the camera to the server. The transfer to the server can be made in the two following
ways:
•Transfer pictures when an alarm occurred in the motion detection area.
•Transfer pictures at designated intervals.
To transfer the pictures to the server, the settings are required in advance.
Only still pictures can be transferred to the server. Transferring motion picture to the server is not possible.
Preparations for Transferring Pictures...

50
TRANSFERRING PICTURES TO THE SERVER
The Alarm page of Alarm&Transmission appears.
The FTP client page of Alarm&Transmission appears.
Screenshot 4
Screenshot 3
Click the [FTP client] tab.
STEP3
Set the items on the FTP client page.
This explanation is only for Common setup.
FTP server address
Enter the address of the server where to trans-
fer the picture. You can enter the IP address or
the host name.
User name
Enter a user name for login in the FTP server,
up to 64 characters.
Password
Enter a...