Panasonic Wv Nm100 Operating Instructions Manual

21
The Local Area Connection Properties window appears.
If the “Internet Protocol (TCP/IP)” item is not displayed, refer to
the operating instructions of the OS and follow the procedures
to install the TCP/IP. 
The Internet Protocol (TCP/IP) Properties window appears.
Screenshot 4
Note
Screenshot 3
Click to select Internet Protocol (TCP/IP), and
then click the [Properties] button.
STEP3
Click the Use the following IP address radio
button and enter the IP address and the subnet
mask as follows.
•IP...

22
SETUP
Using Windows XP (Category View)
Begin the setup when the PC is in the same condition as just
after the startup.
The Control Panel window appears.
The Network and Internet Connections window appears.
Screenshot 3
Screenshot 2
Screenshot 1
Select Control Panel ([Start] - [Control Panel]).
STEP1
Double click the Network and Internet
Connections icon.
STEP2
Double click the Network Connections icon.
STEP3 

23
The Network Connections window appears.
The Local Area Connection Properties window appears.
The Internet Protocol (TCP/IP) Properties window appears.
Screenshot 6
Screenshot 5
Screenshot 4
Click to select Local Area Connection, and
then click Change settings of this connection
in the Network Tasks menu.
STEP4
Click to select Internet Protocol (TCP/IP), and
then click the [Properties] button.
If the “Internet Protocol (TCP/IP)” item is not
displayed, refer to the operating instructions of
the OS and...

24
SETUP
Network Setup of the Camera
After completing the network setup of the PC, begin the network setup of the camera.
If multiple cameras are connected, it is required to set up each camera individually.
The following information is necessary for the network setup of the cameras.
If you do not have the following information, refer to your network administrator or your Internet service provider.
For further information about the terms, refer to page 69.
•IP address
•Subnet mask
•Port number
•Default...

25
The “Top Menu” page of the camera setup appears.
The “Basic setup” page appears.
The “Operation mode” page of “Advanced setup” appears.
Screenshot 5
Screenshot 4
Screenshot 3
Click the [Setup] button.
The login window will appear when you press
the [Camera Control] button or the [Setup]
button on the “Top Menu” page for the first
time. The default settings for user name and
password are as follows.
User name: admin
Password: password
Change the default password for security.
! Important
STEP3
Click...

26
SETUP
The Network page appears.
Screenshot 6
Set parameters for each item in the Network
page.
The parameters differ depending on the con-
nection type (refer to pages 12-14).
For further information, refer to the next page.
Click the [SET] button after completing the
setup.
After you click the [SET] button, the
“Command Executing” message appears.
(This message will appear even when you
click the [SET] button in other windows.)
Avoid doing any operation while the message
is displayed.
! Important...

27
Parameters for the Network setupItems Depending on the Connection Type
Item Connection type Description of the parameter
IP address Connection type 1 Enter “xxx.yyy.zzz.nnn” for the IP address (where “xxx.yyy.zzz”
should be the same numbers assigned to the PC, and “nnn” should
be a number from 2 to 254 except the same IP address already
assigned to the PC and any other cameras).
Connection type 2 Set the IP address designated by your network administrator.
However, the setting is not required if the...

28
SETUP
Network speed Common to all connection  Set the network speed.
types Use the default setting “auto” for the network speed.
Selectable parameters: auto (default setting), 100 Mbps (full
duplex), 100 Mbps (half duplex), 10 Mbps (full duplex), 10 Mbps
(half duplex) 
HTTP port Connection type 1, 2 and 3 Use the default setting “80” for the HTTP port.
Connection type 4 If multiple cameras are connected, it is required to set up each cam-
era individually.
However, the port numbers already assigned to...

29
Installation of the MPEG-4 Plug-in
Installation of the plug-in is required to browse motion pictures.
Insert the provided CD-ROM into the CD-ROM drive of the PC. The launcher software starts up automatically. Click
the [MPEG-4 Installation] button.
After the installer starts up, follow the instructions of the wizard.
•The MPEG-4 plug-in is exclusively designed for Internet Explorer. This plug-in does not work with other
browsers.
•The MPEG-4 plug-in does not work on a Windows NT computer.
•Login as...

30
SETUP
Basic Settings
After completing the network setup of the PC and the camera, begin the basic settings of the camera.
The basic settings are the minimum settings required to operate the camera, such as date setting and setting of
Operation mode.
Begin the setup when the PC is in the same condition as just
after the startup.
The browser starts up. The web page set as the home page in
your browser appears.
(The picture is the page of the Panasonic web site.)
Screenshot 2
Screenshot 1
Start up...