Panasonic Wv Nm100 Operating Instructions Manual

11
INSTALLATIONS
This is an example of an installation onto a wall.
Screws
Wall-mounting bracket 
Install the wall-mounting bracket onto the wall
using the screws.
STEP1
Install the camera onto the wall-mounting brack-
et by referring to the illustration shown on the
left.
It is possible to install the camera upside down.
Install the camera in the upside down position
according to your needs.
Confirm that the Panasonic logo is in the posi-
tion shown in the illustration.
If the logo is upside down,...

12
CONNECTIONS
Connection between a PC and This Camera (Connection type 1)
Connect the camera and the PC directly using an Ethernet cable when browsing the camera pictures or performing
the network settings of the camera.
< Connection example >
< Required cable >
Ethernet cable (category 5 cross cable)
•All cameras connected to the network must use their own exclusive AC adapter.
•Use only the specified Ethernet cable, category 5 cross cable.
! Important
Before starting the connections, confirm which...

13
Using with an Intranet (LAN) (Connection type 2)
Connect the camera to an intranet (LAN) using an Ethernet switching hub or router when browsing camera pictures
of a camera installed in the same LAN (the intranet of a company or home).
< Connection example >
< Required hardware >
Ethernet switching hub or router
< Required cable >
Ethernet cable (category 5 straight cable)
•Use an Ethernet switching hub or router suitable for 10Base-T/100Base-TX.
•Install also a LAN card suitable for...

14
CONNECTIONS
Using via the Internet (Connection type 3-4)
Connecting the camera to the Internet using an xDSL modem or a cable modem.
< Connection example >
< Required hardware >
•Cable modem or xDSL modem
•Broadband router
< Required cable >
Ethernet cable (category 5 straight cable)
•When the camera is connected using connection type 3 or 4, obtain the global IP address from the Internet ser-
vice provider. Perform the settings of the camera by connecting the camera and the PC directly. (Refer to...

15
SETUP
After completing the connections, it is necessary to set up the network of the PC and the camera.
To operate the camera connected in a network such as a LAN or the Internet, it is necessary to set up the network.
Use the provided Panasonic IP Setup software to set up the network of the camera. (Refer to the next page).
If the setup with the provided software fails, set up the PC and the camera separately. For further information, refer
to pages 18 - 28.
Preparations for the Setup
Prepare the...

16
SETUP
Setup with the Provided Panasonic IP SetupSoftware
Set up the network of the camera by using the Panasonic IP Setup software included on the CD-ROM provided
with the camera.
The Panasonic IP Setup starts up.
The MAC address and the IP address of the connected camera
will be displayed. (Click the “REFRESH” button if they are not
displayed.)
Screenshot 1
Click the MAC address/IP address of the cam-
era to be set up.
Click the [NETWORK SETUP] button.
•When two or more cameras are connected,
the MAC...

17
Set parameters for each item.
IP Address
Subnet Mask
Default Gateway
HTTP Port
Enter parameters depending on your environ-
ment.
For further information about the parameters,
refer to pages 27-28.
DHCP
DNS
Click the [Enable] radio button when using the
DHCP and the DNS.
When using the DNS function, enter the
“Primary DNS Server address” and the
“Secondary DNS Server address”.
•If DHCP is enabled although there is no
DHCP server in the network, check
“Disable” for DHCP in the “Panasonic IP
Setup”...

18
SETUP
Begin the setup when the PC is in the same condition as just
after the startup.
The Control Panel window appears.
Screenshot 2
Screenshot 1
Select Control Panel ([Start] - [Settings] -
[Control Panel]).
STEP1
Click once to select the [Network] icon.
STEP2
Network Setup of the PC 
To set up the network of the PC, first change the TCP/IP settings of the PC to match them to the default settings of
the camera. The following are the default network settings of the camera.
•IP address: 192.168.0.10...

19
The Network window appears.
If the “TCP/IP” item is not displayed, refer to the operating
instructions of the OS and follow the procedures to install the
TCP/IP. 
The TCP/IP Properties window appears.
Screenshot 4
Note
Screenshot 3
Click the [Configuration] tab.
Click to select the TCP/IP protocol of the cur-
rently used network card.
Click the [Properties] button.
STEP5
STEP4
STEP3
Click the [IP Address] tab.
Click the Specify an IP address radio button.
Enter the IP address and the subnet mask as...

20
SETUP
Using Windows 2000
The following procedures are examples when using Windows 2000. You can proceed in the same way when using
Windows NT.
Log in as one of the administrators before beginning the setup.
! Important
Begin the setup when the PC is in the same condition as just
after the startup.
The Network and Dial-up Connections window appears.
Screenshot 2
Screenshot 1
Select Network and Dial-up Connections
([Start] - [Settings] - [Network and Dial-up
Connections]).
STEP1
Click the right mouse...