Panasonic Va-208 Key Telephone System Installation Manual

3. PROGRAMMING SETTINGS 
SYSTEM SETTING 
HOLD-ON ALARM 
This feature will generate a ring alarm indicating that a call has been left on HOLD longer than the preset time. The alarm 
can be programmed to ring after a call has been left on HOLD for 30 seconds, 1 minute, 2 minutes or No Alarm. 
0 The initial program setting is for No Alarm. 
+ To change the program setting, perform the following steps: 
Step 1 
Step 
2 
Step 3 
Step 4 
4a. 
4b. 
4c. 
4d. 
Step 5 
Step 
6 Place the system in the programming...

Step 2 
Step 3 
Step 4 
4a. 
4b. 
Step 5 
Step 6 
SYSTEM SETTINGS 
LdNG SPEECH ALARM 
Place TEL Station 1 in the programming mode by depressing the SPKR button. 
Dial the feature program activation Code B p[ ‘F] 
Activate only one (1) of the following options: 
To activate the 
LONG SPEECH ALARM, depress the SPKR button, if extinguished, 
to 
light the LED lamp. 
OR 
To deactivate the LONG SPEECH ALARM, depress the SPKR button, 
if on, to 
extinguish the LED lamp. r%zJ-XJ 
Depress the # button on the...

SYSTEM SETTING 
INCOMING ALARM TIME 
This feature establishes a time period, of either 20 or 30 seconds, to activate tone ringing at all stations if an incoming 
call is not answered within a 20 or 30 second time frame. Reference must be made to the COL Settings-incoming COL 
Call Arriving Alarm to program the COL 
1 and COL 2 lines for the alarm tone. 
0 The initial program setting is for the alarm to ring after 30 seconds. 
0 To change the program setting, perform the following steps: 
Step 1 
Step 
2...

FYSTEM SETTINGS 
AUTO PAUSE 
4b. To deactivate the AUTO PAUSE, depress the COL 2 button, if on, 
the LED lamp. to extinguish 
-1 
Step 5 Depress the # button on the Dial Pad to store the program established in Step 4. 
Step 6 Proceed to next feature program or depress FLASH button and SPKR button in sequence to end programming 
mode at TEL Station 1. 
SPEED DIALING STORED COMMON NUMBERS 
This feature allows commonly dialed telephone numbers to be stored in the system memory for access by all unrestricted...

COL SETTINGS 
DIALING METHOD 
0 
To change the program setting, perform the following steps: 
Step 1 
Step 
2 
Step 3 
3a. 
Place the system in 
Place TEL Station 1 
Dial the appropriate the programming mode. See instructions in the General Operational Procedures. 
in programming mode by depressing the SPKR button. 
Feature Program Activation Code for the COL to be programmed. 
Step 4 
4a. 
For COL l-Dial Feature Program Activation Code 
For COL 2-Dial Feature Program Activation Code 
Activate only one...

COL SETTINGS 
’ TYPE OF LINE 
Step 4 Activate only one (1) of the following options: 
4a. To set the TYPE OF LINE for a Central Office line, depress the SPKR button, 
if 
on, 
to extinguish the LED lamp. 
OR 
4b. To set the TYPE OF LINE for a PBX line, depress the SPKR button, if extinguished, 
to light the LED associated with the button. 
Step 5 Depress the # button on the Dial Pad to store the program established in Step 4. Option 
I SPKR 
PBX 1 ON 
Step 
6 
Proceed to next feature program or to end...

KEY TELEPHONE SETTINGS 
COL INCOMING RING 
This setting will program TEL Station tone ringing for incoming calls. The TEL Stations can be programmed for Incoming 
Call Ringing for either COL 1 or COL 2 or for both. 
NOTE: Only one TEL Station can be programmed at a time. To change the COL INCOMING RING on multiple TEL Stations, 
complete Steps 1 thru 6 for the first TEL Station and then repeat Steps 3 thru 6 for each remaining TEL Station 
you wish to change. 
0 The initial program setting is for both...

KEY TELEPHONE SETTINGS 
COL INCOMING RING 
Step 6 Depress the # button on the Dial Pad to store the program established in Step 4. 
Step 7 Proceed to next feature program or to end programming, depress FLASH button and SPKR button in sequence. 
NIGHT INCOMING RING 
This setting is to specify whether an incoming call received after office hours can be answered on a particular TEL Station. 
Each TEL Station must be individually programmed for NIGHT INCOMING RING. 
NOTE: Only one TEL Station can be...

KEY TELEPHONE SETTINGS 
DOORPHONE CALL 
This feature is to designate what group of TEL Stations are capable of communicating with Doorphones. Up to two doorphones 
can be connected, DOORPHONE A and DOORPHONE B. Up to five TEL Stations can be connected to each Doorphone 
to receive the incoming.ringing tone of the respective Doorphone. Each TEL Station must be individually programmed for 
Doorphone Call. 
NOTE: Only one TEL Station can be programmed at a time. To change the DOORPHONE CALL on multiple TEL...

KEY TELEPHONE SETTINGS 
DOORPHONE CALL 
4c. To set the TEL Station to receive DOORPHONE A and DOORPHONE 
S CALL, depress COL 1 and COL 2 buttons, 
if extinguished, to light 
the LED lamps. Option 
j COL 1 1 COL 2 
DP NB Conn. 
ON 1 of4 
OR 
4d. To set the TE.L Station to not receive a DOORPHONE CALL, depress 
COL 1 and COL 2 buttons, 
if on, to extinguish the LED lamps. Option 
1 COL 1 1 COL 2 
DPAIB Not Corm 1 OFF 1 OFF 
Step 5 Depress the # button on the Dial Pad to store the program established in...