Panasonic Sv As3 Operating Instructions Manual

							41VQT0P18
1Press the [MENU] button and then set the item with the 
Jog Ball. (P20)
∫Manual adjustment
After setting to [EV manual] in Step 1,
2Roll the Jog Ball left or right to 
compensate the exposure.
 You can compensate it from j2 EV to i2 EV 
in steps of 1/3 EV.
 When the exposure is compensated toward 
positive, the picture will be recorded brighter. 
When the exposure is compensated toward 
negative, the picture will be recorded darker.
Press the Jog Ball to set the 
exposure.
≥When the exposure is compensated, the brightness of the picture on 
the LCD Monitor may differ from that of the picture actually recorded. 
Check the brightness by playing the picture.
≥EV is an abbreviation of Exposure Value, and it is the amount of light 
given to the CCD.
Compensating the Exposure
Use this function when you cannot achieve appropriate exposure due 
to the difference of brightness between the subject and the 
background, etc.
Exposure
l
EV autoThe exposure is automatically 
determined.
EV manualThe exposure can be adjusted 
manually.
EXITADJUST ENTERMENU
VQT0P18Eng.book  41 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							42VQT0P18
1Press the [MENU] button and then set the item with the 
Jog Ball. (P20)
≥When you take a picture in high ISO sensitivity, picture noise 
appears and the picture quality is deteriorated.
≥When the picture is still dim even if the ISO sensitivity is increased, 
set [Sensitivity] to [Auto] and use the flash. (The available flash range 
is about 2.6–3.9 ft. (80 cm–120 cm).)
≥You cannot use this function when you record pictures in [MPEG4] 
mode.
Setting the ISO Sensitivity
ISO sensitivity represents the sensitivity to light in values. It is useful 
when taking pictures without the flash.
Advanced 
setuplSensitivityl
AutoThe ISO setting is automatically 
adjusted according to the 
brightness. 
  
100
200
400The more the ISO sensitivity is 
adjusted, the more this unit 
becomes suitable for recording 
in dark places.
Recording (continued)
VQT0P18Eng.book  42 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							43VQT0P18
∫Selecting the desired playback mode
1Slide the Power Switch to [ON].
– The Power Lamp lights in red.
Slide the Record/Playback Mode 
Switch to the playback mode [ ].
2Press the [MODE] button and then 
select the desired mode with the Jog 
Ball.
 Refer to the table below to select the mode.
Playback
Picture
EXIT
Playback modesPlayable filesAudio
Picture
 (Still picture 
playback)[Picture] files and still 
picture files (JPEG 
format) recorded with 
this unitCannot be played.
MPEG4
(Motion image 
playback)[MPEG4] files and 
motion image files 
(ASF format) recorded 
with this unitPlayed from the stereo 
earphones (supplied). 
(The audio cannot be 
played from this unit.)
Vo i c e
(Audio playback)[Voice] files recorded 
with this unit
Audio
(Music playback)Audio files recorded 
onto a card with 
SD-JukeboxRefer to P61 for details 
about playing music.
Playback
VQT0P18Eng.book  43 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							44VQT0P18
3Roll the Jog Ball right or left to select 
the file you want to play.
 Roll the Jog Ball to the right to display the next 
file.
 Roll the Jog Ball to the left to display the 
previous file.
∫When selecting [MPEG4] or [Voice]
After you select the file in Step 3,
4Press the Jog Ball to start playback.
–[1] appears during playback.
 If there are multiple files, the files will be played 
continuously.
 You can fast-forward or fast-rewind the file with the remote controller. 
When you keep pressing [9] ([:]) button, the file is fast-forwarded 
(fast-rewound). When you tap them, you can move to the beginning of 
the next (current) file.
5Press the Jog Ball to pause playback.
–[∑] appears while playing is stopped.
 When you stop playback halfway and start 
playback again, the file will be started from the 
position where you previously stopped. 
(Resume playback)
Playback (continued)
VQT0P18Eng.book  44 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							45VQT0P18
≥When playing a still picture, the [ ] icon appears for a moment and 
the resolution of the picture may look deteriorated a little. However, 
the picture is played with normal quality later.
≥When starting the resume playback, the file preceeding the position 
where you stopped will be played. 
≥Some files may not be played on this unit even if the files are in 
JPEG or ASF (MPEG4) format.
≥[Voice] files cannot be played on Panasonic IC recorders.
≥MPEG4 and Voice files recorded on Panasonic SD Multi Camera 
SV-AS10 cannot be played on this unit.
≥When a still picture recorded with other equipment is played on this 
unit, the following may occur.
 The picture cannot be played.
 The resume playback cannot be operated.
 The quality of pictures may be deteriorated.
 The file size may not be displayed.
 The date/time indication is different from the date/time when the picture 
is created.
≥If you change the folder name or the file name of a picture on your 
PC, the picture may not be played.
≥The date/time indication is stopped while [MPEG4] files are played.
∫When playing in [Voice] mode
≥If you do not operate this unit for 10 seconds after you start playback, 
the LCD Monitor will turn off to save power. (The Card Access Lamp 
blinks during playback.) If you turn the LCD Monitor on again, press 
the [MENU] button on this unit.
≥You can avoid operational mistakes on this unit by pressing down the 
[MODE] button (for more than about 2 seconds). (P64)
≥[Voice] files are fast-forwarded (fast-rewound) at a speed of 10k for 
the first 6 seconds. After that, the files will be fast-forwarded (fast-
rewound) at a speed of 60k.
VQT0P18Eng.book  45 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							46VQT0P18
1Press the Volume button.
 The volume turns up with [i].
The volume turns down with [j].
 If the volume adjustment screen is not 
operated for a while after adjustment, it will 
automatically disappear.
≥When you want to listen to the audio being played, connect the 
remote controller and the stereo earphones (supplied). (The unit is 
not equipped with a speaker.)
≥You can also adjust the volume on the remote controller. (P13)
1Roll the Jog Ball down while the 
playback is stopped.
 In [Voice] mode, the list of files which have no 
thumbnails are displayed.
∫To select a file and play 1 picture
After you display 6 files in Step 1,
2Roll the Jog Ball to select the file.
 If 7 or more files are recorded, the files will be 
displayed on the subsequent pages.
Press the Jog Ball.
– The selected file starts playback.
Adjusting Volume
6 Pictures Multi Playback (Thumbnail Display)

Playback (continued)
VQT0P18Eng.book  46 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							47VQT0P18
1Set the mode to [MPEG4] mode. (P43)
2Press the [MENU] button and then set the item with the 
Jog Ball. (P20)
1Press the [MENU] button and then set the item with the 
Jog Ball. (P20)
Playing Motion Images Repeatedly (Repeat Playback)
Repeat
l
OFFStops playback after the last 
file is played.
Repeat oneRepeats playing a file.
Repeat allRepeats playing all files.
Deleting Files
Once deleted, files cannot be recovered. Check the files before 
deleting.
Erase filel
Erase oneErases files one by one.
Erase allErases all files in the 
mode where you are 
playing files.
VQT0P18Eng.book  47 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							48VQT0P18
2Select the files to be deleted and then 
press the Jog Ball. 
(Only when [Erase one] is selected)
3Select [Yes] on the confirmation 
screen and then press the Jog Ball.
 Press the [MENU] button to exit this setting.
≥You cannot delete protected files (P49), music files and files that do 
not conform to DCF standard on this unit.
≥Be sure to delete [Voice] files on this unit.
≥When you delete files on this unit, the DPOF information set on other 
equipment can also be deleted.
≥Image files which cannot be played on this unit (other than JPEG) 
can be deleted.
≥Do not turn this unit off or remove the card when deleting.
≥It takes some time to delete many files at the same time. Use a fully 
charged battery.
Playback (continued)
VQT0P18Eng.book  48 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							49VQT0P18
 
1Press the [MENU] button and then set the item with the 
Jog Ball. (P20)
2Select the files to be protected and 
then press the Jog Ball.
– [ ] appears on the bottom of the LCD 
Monitor.
 You can select the desired files until you press 
the [MENU] button.
∫When you release protection
Select protected files in Step 2 and then press the Jog Ball.
∫When you release protection on all files
Select [Unlock all] in Step 1, select [Yes] on the confirmation screen 
and then press the Jog Ball. Protection on all files in the playback mode 
currently selected can be released.
≥If you format the card, protected files will also be deleted.
≥The lock setting may not be effective in other equipment.
≥Sliding the SD Memory Card Write-Protect switch (P11) to “LOCK” 
prevents the file from deletion even if the protection is not set.
≥[Voice] files can be automatically protected when they are recorded.
≥It takes some time to set many files at the same time. Use a fully 
charged battery.
Preventing Accidental Deletion of Files (Lock Setting)
This function prevents deleting or altering precious files by mistake.
LocklLock/Unlock
VQT0P18Eng.book  49 ページ  ２００５年１月１２日　水曜日　午前９時１１分 
						

							50VQT0P18
1Select a picture in [Picture] mode. (P43)
2Roll the Jog Ball upwards.
– The target frame appears on the LCD Monitor.
3Roll the Jog Ball up or down to select 
the zoom magnification and then 
press the Jog Ball.
 The more you roll the Jog Ball upwards, the 
more the zoom magnification is increased (up 
to 10k).
4Roll the Jog Ball to move the target 
frame to the position you want to 
enlarge and then press the Jog Ball.
– The picture in the target frame is enlarged.
 After enlarging the picture, the magnification is 
restored to 1
k by pressing the Jog Ball or 
rolling it right or left.
 Repeat Steps 2–4 if you want to enlarge the picture more.
Enlarging Pictures (Target Zoom)
You can enlarge the picture up to 10k.
1. 21. 2t
4.04.0t
4.04.0t
Playback (continued)
VQT0P18Eng.book  50 ページ  ２００５年１月１２日　水曜日　午前９時１１分