Panasonic Sdr S10 Operating Instructions Manual

							81VQT1D97
With other products
8Select the paper size setting 
on [PAPER SIZE].
≥You cannot set paper sizes not 
supported on the printer.
9Select the layout setting on 
[PAGE LAYOUT].
≥You cannot set page layouts not 
supported on the printer.
10Select [PRINT] # [YES] and 
then press the cursor button 
in the center.
The pictures are printed.≥Exit PictBridge by disconnecting 
the USB cable after the pictures 
have been printed.
When you want to stop printing 
halfway
Press the cursor button down.
A confirmation message appears. If 
[YES] is selected, the number of prints 
set is canceled and the screen returns to 
step 4. If [NO] is selected, all the settings 
are kept and the screen returns to 
step 4.
≥Avoid the following operations during 
printing. These operations disable 
proper printing. 
jDisconnecting the USB cable
jOpening the card/battery door
jSwitching the mode dial
jTurning off the power
≥Check the settings for the paper size, 
quality of print, etc. on the printer.
≥You may not be able to print still 
pictures recorded with other products.
≥When the unit is connected directly to 
the printer, the DPOF settings cannot 
be used.
≥Connect the printer directly to this unit. 
Do not use a USB hub. [STANDARD]:Size specific to the 
printer
[4t5 INCH]:L size
[5t7 INCH]:2L size
[4t6 INCH]:Postcard size
[A4]:A4 size
[STANDARD]:Layout specific to the 
printer
[]:No frame print
[]:Frame print
VQT1D97(ENG).book  81 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							With a computer
82VQT1D97
With a comp ute r
With a computer (Windows)
When the CD-ROM (supplied) is inserted into the 
computer, the [Setup Menu] screen will appear.
∫Video editing software MotionSD STUDIO 1.2E
This software allows pictures to be acquired from this unit, edited and output.
You can also send a picture acquired from this unit by e-mail and edited pictures can be 
written to the DVD drive.
For information about how to use MotionSD STUDIO 1.2E, read the PDF operating 
instructions. (l88)
∫Acrobat Reader
To view the installed operating instructions of MotionSD STUDIO, Adobe Acrobat 
Reader 5.0 or later is required.
If Adobe Acrobat Reader is not installed in the computer you intend to use, click the 
desired language in the setup screen (or open a folder of the name of the desired 
language in the [Adobe] folder and then double-click [AR505XXX.exe] or 
[AR500XXX.exe] file). (“XXX” (the last 3 characters in the name of the file) varies 
depending on the language folder you selected.) Then follow the message on the 
screen to install Adobe Acrobat Reader.
∫DirectX
You will need Microsoft DirectX 9.0b or 9.0c in order to use MotionSD STUDIO. (It can 
also be installed when you install MotionSD STUDIO.) If DirectX is not installed on your 
computer because you canceled its installation when installing the software, click 
[DirectX] in the [Setup Menu] and follow the on-screen messages to install it.
≥Depending on the operating environment, software applications supporting the old 
version of DirectX may not run properly after DirectX 9.0b has been installed. If this 
happens, contact the manufacturer of these applications. 
(Your computer must support DirectX 9.0)
≥We cannot guarantee proper operation of this unit if you use software other than that 
supplied.
What you can do with a computer
VQT1D97(ENG).book  82 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							With a computer
83VQT1D97
Before opening the CD-ROM package, please read the following.
End User License Agreement
You (“Licensee”) are granted a license for the Software defined in this End User License Agreement 
(“Agreement”) on condition that you agree to the terms and conditions of this Agreement. If 
Licensee does not agree to the terms and conditions of this Agreement, promptly return the 
Software to Matsushita Electric Industrial Co., Ltd. (“Matsushita”), its distributors or dealers from 
which you made the purchase. 
Article 1 LicenseLicensee is granted the right to use the Software, including the information recorded or described 
on the CD-ROM, instruction manuals, and any other media provided to Licensee (collectively 
“Software”), but all applicable rights to patents, copyrights, trademarks and trade secrets in the 
Software are not transferred to Licensee.
Article 2 Use by a Third PartyLicensee may not use, copy, modify, transfer or allow any third party, whether free of charge or not, 
to use, copy or modify the Software, except as expressly provided for in this Agreement.
Article 3 Restrictions on Copying the SoftwareLicensee may make a single copy of the Software in whole or in part solely for back-up purpose.
Article 4 ComputerLicensee may use the Software only on one computer, and may not use it on more than one 
computer.
Article 5 Reverse Engineering, Decompiling or DisassemblyLicensee may not reverse engineer, decompile, or disassemble the Software, except to the extent 
either of them is permitted under law or regulation of the country where Licensee resides. 
Matsushita, or its distributors will not be responsible for any defects in the Software or damage to 
Licensee caused by Licensee’s reverse engineering, decompiling, or disassembly of the Software.
Article 6 IndemnificationThe Software is provided “AS-IS” without warranty of any kind, either expressed or implied, 
including, but not limited to, warranties of non-infringement, merchantability and/or fitness for a 
particular purpose. Further, Matsushita does not warrant that the operation of the Software will be 
uninterrupted or error free. Matsushita or any of its distributors will not be liable for any damage 
suffered by Licensee arising from or in connection with Licensee’s use of the Software.
Article 7 Export ControlLicensee agrees not to export or re-export to any country the Software in any form without the 
appropriate export licenses under regulations of the country where Licensee resides, if necessary.
Article 8Termination of LicenseThe right granted to Licensee hereunder will be automatically terminated if Licensee contravenes 
any of the terms and conditions of this Agreement. Upon termination hereof, Licensee must destroy 
the Software and related documentation together with all the copies thereof at Licensee’s own 
expense.
VQT1D97(ENG).book  83 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							With a computer
84VQT1D97
≥A CD-ROM drive is necessary to install the supplied software.
≥When 2 or more USB devices are connected to a computer, or when devices are 
connected through USB hubs or by using extension cables, proper operation is not 
guaranteed.
≥Use the supplied USB cable when connecting to the computer. (Operation is not 
guaranteed with any other USB cables.)
≥Even if the system requirements mentioned in these operating instructions are 
fulfilled, some computers cannot be used.
≥This software is not compatible with Microsoft Windows 3.1, Windows 95, Windows 
98/98SE, Windows Me and Windows NT.
≥Operation on an upgraded OS is not guaranteed.
≥Operation on an OS other than the one pre-installed is not guaranteed.
∫MotionSD STUDIO 1.2E
Operating environment
Personal 
computerIBM PC/AT compatible personal computer
OSMicrosoft Windows 2000 Professional Service Pack 4
Microsoft Windows XP Home Edition Service Pack 2
Microsoft Windows XP Professional Service Pack 2
CPUIntel PentiumIII 800 MHz or higher (including compatible CPU)
(Intel Pentium 4 1.6 GHz or higher recommended)
RAM256 MB or more (512 MB or more recommended)
DisplayHigh Color (16 bit) or more (32 bit recommended)
Desktop resolution of 1024k768 pixels or more (1280k1024 
pixels or more recommended)
Graphic accelerator supporting DirectX 9.0b or 9.0c, and 
DirectDraw overlay
Free hard disk 
spaceUltra DMA—33 or more (100 or more is recommended)
640 MB or more (When writing to DVD, the same amount of free 
space as the disc is necessary.)
Necessary 
softwareDirectX 9.0b or 9.0c
(If you install the software in a personal computer that is not 
compatible with DirectX 9.0b or 9.0c, the personal computer 
may stop operating properly. If you are unsure if your personal 
computer is compatible, contact the maker.)
Windows Media Player 6.4 to 10
SoundDirectSound Support
VQT1D97(ENG).book  84 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							With a computer
85VQT1D97
≥The supplied CD-ROM is available for Windows only.
≥Operation is not guaranteed on computers that are not IBM PC/AT compatible.
≥This software is not compatible with a multi-boot environment.
≥This software is not compatible with a multi-CPU environment.
≥Operation on Microsoft Windows XP Media Center Edition, Tablet PC Edition and 64-
bit operating system is not guaranteed.
≥Depending upon the environment of your computer, if it does not support Hi-Speed 
USB (USB 2.0), for example, frame dropout may occur, the audio may be intermittent 
or the software may run slowly when you play back recorded images.
≥Set the display resolution to 1024k768 (16 bits color) or higher.
Select [start] # ([Settings] #) [Control Panel] # ([Appearance and Themes] #) 
[Display] and select [Settings] tab and then adjust [Screen resolution] and [Color 
quality].
∫Operating environment for the card reader/writer function 
(Mass storage)
≥The USB equipment operates with the driver installed as standard in the OS.
Disc driveCD-ROM drive (When writing to DVD, a compatible drive and 
media are necessary.)
InterfaceUSB port (Hi-Speed USB (USB 2.0) recommended)
Other 
requirementsMouse or equivalent pointing device
Personal 
computerIBM PC/AT compatible personal computer
OSMicrosoft Windows 2000 Professional Service Pack 4
Microsoft Windows XP Home Edition
Microsoft Windows XP Professional
CPUIntel PentiumIII 450 MHz or higher or Intel Celeron 400 MHz or 
higher
RAM128 MB or more (256 MB or more recommended)
InterfaceUSB port
Other 
requirementsMouse or equivalent pointing device
VQT1D97(ENG).book  85 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							86VQT1D97
With a computer
When installing the software, log on to 
your computer as the Administrator or 
with a user name with equivalent 
authorization. (If you do not have 
authorization to do this, consult your 
manager.)
≥Before starting the installation, close 
any other software applications which 
are running.
≥Do not perform any other operations 
on your computer while the software is 
being installed.
1Insert the CD-ROM into the 
computer.
 
The [Setup Menu] screen is 
displayed.
≥If the [Setup Menu] screen is not 
displayed, double-click the CD-
ROM drive icon containing the CD-
ROM in [My Computer].
2Click [MotionSD STUDIO 
1.2E].
 
≥The software application may not 
run properly if you cancel the 
installation at any point e.g. by 
pressing [Cancel].
3Click [Next]. 
≥Continue to follow the on-screen 
messages to install it.
4Select the video system. 
Installing MotionSD 
STUDIO
VQT1D97(ENG).book  86 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							87VQT1D97
With a computer
5After the installation is 
complete, [Readme.txt] are 
displayed. Check the 
contents, then click [t] on top 
right of the window.
6Click [Finish].
≥Depending on the operating 
environment, you may be required 
to install DirectX 9.0b. If so, click 
[Yes] and install it.
≥If it is necessary to reboot the 
computer after the application 
has been installed, click [Yes] 
and reboot it.
≥If you install the software in a computer 
that is not compatible with DirectX 9.0b 
or 9.0c, the computer may stop 
operating properly. If you are unsure 
whether or not your computer is 
compatible, contact the maker of your 
computer.
≥After the installation is finished, the 
icon [ ] is displayed in the task tray 
on the computer screen. If you connect 
this unit and a computer with the USB cable, the [SD Browser auto start] 
screen appears for starting 
MotionSD STUDIO. (l89)
VQT1D97(ENG).book  87 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							88VQT1D97
With a computer
For details on how to use MotionSD 
STUDIO, read the PDF instructions.
Select [start]>
[All Programs (Programs)]>
[Panasonic]>
[MotionSD STUDIO 1.2E]>
[Manual].
≥After starting the software, on the 
menu select [Help]>[Manual] to 
display the help files.
≥You will need Adobe Acrobat Reader 
5.0 or later version to read the PDF 
operating instructions. (l82)After the software is installed, the unit 
must be connected to the computer and 
be correctly recognized by the computer.
≥Connect after installing the software.
≥If the supplied CD-ROM is inserted in 
the computer, remove it. (If the installer 
setup is running, wait until it finishes, 
then remove the CD-ROM.)
≥If the recognition procedure is not 
accomplished properly, operation will 
not be possible after connecting the 
unit to the computer.
≥If the unit fails to operate normally, it 
may mean that you have not 
conducted the installation or 
recognition procedure properly.
1Slide the terminal cover lock 
to OPEN and then open the 
terminal cover.
2Connect this unit to the AC 
adaptor and turn on the unit.
≥Be sure to set the mode dial to 
OFF when connecting the AC 
adaptor to this unit.
Reading the MotionSD 
STUDIO operating 
instructionsConnection and 
recognition procedures
VQT1D97(ENG).book  88 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							89VQT1D97
With a computer
3Connect this unit and a 
computer.
AUSB cable (supplied)
≥Insert the plugs as far as they will 
go. The unit and computer will not 
operate properly if the plugs are 
not inserted fully.
≥Do not use any other USB 
connection cables except the 
supplied one. 
(Operation is not guaranteed with 
any other USB cables.)
4Press the cursor button up or 
down to select 
[PC CONNECT], then press 
the cursor button in the 
center.
5The [SD Browser auto start] 
screen appears.
≥If [Yes] is clicked, 
MotionSD STUDIO starts. (l92)
≥Click [No] if you do not want to 
start MotionSD STUDIO.
≥When the unit is connected to a 
computer, its power cannot be 
turned off.
In this case, disconnect the USB cable 
(l93).
≥When a computer is accessing the 
card in this unit, the card access lamp 
lights. (  appears on the LCD 
monitor.) Do not disconnect the USB 
cable or AC adaptor while the card is 
being accessed as it may damage the 
data.
≥It may be necessary to reboot the 
computer after connecting this unit to it 
for the first time.
A
VQT1D97(ENG).book  89 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							90VQT1D97
With a computer
To verify if this unit is correctly 
recognized by the computer, turn on this 
units power and then connect the unit to 
the computer with a USB cable and 
follow the steps below.
≥With some computers including those 
made by NEC, the Device Manager 
may not be displayed if a mode that 
places restrictions on the functions has 
been established. Consult the 
manufacturer or follow the steps in 
your computer’s operating instructions 
to establish a mode in which all the 
functions can be used, then proceed 
with operation.
1Select [start] > ([Settings] >) 
[Control Panel] > 
([Performance and 
Maintenance] > ) [System].
 
2Click the [Hardware] tab, then 
click [Device Manager].
 
3Verify the following items are 
displayed.
∫If the driver has been 
recognized properly
[USB Mass Storage Device] appears at 
[Universal Serial Bus controllers].
∫If the driver has not been 
recognized properly
[!] or [Unknown device] appears at 
[Universal Serial Bus controllers] or 
[Other devices], etc.
(Where the display will appear depends 
on the type of computer you are using.)
You can use the following methods to 
enable the driver to be recognized.
Method 1:  Turn off the unit and your 
computer once and try 
verifying again.
Method 2:  Remove the SD card and try 
verifying again.
Method 3:  Try connecting the unit to 
another USB port on your 
computer.
Verifying that the unit 
is correctly recognized 
by the computer
VQT1D97(ENG).book  90 ページ  ２００７年３月２０日　火曜日　午後５時３３分