Panasonic Sdr S10 Operating Instructions Manual

							Others
101VQT1D97
Messages
CANNOT RECORD.Data writing to the SD card has failed.
NO DATA.There are no motion pictures or still pictures 
recorded on the SD card.
If this message appears although data is recorded 
on the SD card, the condition of the card is probably 
not stable.
Turn off the power and then turn it on again.
THIS CARD CANNOT 
RECORD IN VIDEO MODE.An 8 MB or 16 MB SD card has been inserted in 
video recording mode.
CHECK CARD.This card is not compatible or it cannot be 
recognized by the unit.
CARD LOCKED.The write protection switch on the SD card is set to 
LOCK. (l22)
CARD FULL.
The SD card is full or the number of scenes or 
programs has reached the maximum limit so no 
further data can be recorded. Delete unnecessary 
scenes (l70) or insert a new SD card.
SCENE NUMBER IS FULL.
CANNOT RECORD. THE 
NUMBER OF PROGRAM IS 
FULL.
CARD DOOR OPENED.The card/battery door is open. Close it.
ERROR OCCURRED. 
RECORDING IS STOPPED.≥When using an SD card that can be used for 
motion picture recording (l22)
When this message appears, it is recommended 
that you format the SD card being used. (l74) 
When an SD card is formatted, all the data recorded 
on it will be deleted. Back up the data on the SD 
card to a computer, etc. before formatting the SD 
card.
≥When using any other card
Use a Panasonic SD card or another SD card which 
can be used to record motion pictures. (l22)
VQT1D97(ENG).book  101 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
102VQT1D97
It is possible that the system cannot complete writing of a file normally when, for 
example, power is turned off for some reason during recording or editing.
If faulty management information is found when the card is accessed, the following 
message may appear. Be sure to follow the messages. (Repairing may take time 
depending on the error.)
≥When you repair the data, use a battery with sufficient battery power or the AC 
adaptor. Even if the power is turned off without repairing the data, you can repair the 
data when you turn the power on again.
≥Depending on the condition of the data, it may not be possible to completely repair 
the data.
≥Do not repair a card that has been recorded on another device. This may cause the 
loss of data or the card.
≥If the recovery fails, you will no longer be able to play back the scenes recorded 
before the power went off.
≥If the recovery fails, format the SD card on this unit. Please be aware that if an SD 
card is formatted, then all the data recorded on the card will be erased.
EXIT THE MENU THEN 
CHANGE TO MANUAL 
MODE.You are attempting to use a function that cannot be 
used simultaneously.
CANCEL MAGICPIX MODE.
PLEASE CONNECT AC 
ADAPTORYou are attempting to connect to a computer when 
the AC adaptor is not connected.
PUSH THE RESET 
SWITCH.An irregularity in the unit has been detected. 
Remove the SD card then press the RESET button 
to restart the unit. (
l109)
DISCONNECT USB 
CABLE.The unit cannot correctly establish the connection 
to the computer or printer. Disconnect and 
reconnect the USB cable and then select the 
desired USB function again.
CANNOT OPERATE WHILE 
CONNECTED TO 
COMPUTER.The unit’s power cannot be turned off when the unit 
is connected to the computer.
About recovery
CARD ERROR DETECTED. NOW REPAIRING DATA.
VQT1D97(ENG).book  102 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
103VQT1D97
Functions that cannot be used simultaneously
Some functions in this unit are disabled or cannot be selected due to the unit’s 
specifications. The table below shows examples of functions restricted by 
various conditions.
FunctionsConditions which
disable the functions
Digital zoom
≥In picture recording mode
Fade
MagicPix≥In picture recording mode
≥While recording (Cannot set or cancel)
Backlight compensation≥When the MagicPix function is used
≥When the iris/gain is set
Soft skin mode (Set and 
cancel)
≥While recording
Help mode
Image stabilizer function≥In picture recording mode
≥When the MagicPix function is used
Scene mode≥When the unit is in AUTO mode.
≥When the MagicPix function is used
Change of white balance≥When digital zoom is used
≥When the MagicPix function is used
Adjusting the shutter 
speed, iris/gain≥When the MagicPix function is used
≥When the scene mode is used
VQT1D97(ENG).book  103 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
104VQT1D97
Troubleshooting
ProblemCheck points
This unit cannot be 
turned on.
The status 
indication flashes 
when the unit is 
turned on while 
using the battery.≥Is the battery fully charged?
#Charge the battery using the AC adaptor. (l25)
This unit is turned 
off automatically.≥If you do not use the unit for approximately 
5 minutes, the power is automatically turned off to 
conserve the battery charge. To resume recording, 
turn the power back on.
The power will not turn off automatically when the 
power save function (l97) is set to [OFF].
This unit does not 
stay on long 
enough.≥Is the battery low?
#If the remaining battery power indication is flashing or 
the message “LOW BATTERY.” is displayed, the 
battery has run down. Charge the battery. (l25)
Battery runs down 
quickly.≥Is the battery fully charged?
#Charge it with the AC adaptor. (l25)
≥Are you using the battery in an extremely cold place?
#The battery is affected by ambient temperature. In cold 
places, the operating time of the battery becomes 
shorter.
≥Has the battery worn out?
#The battery has a limited life. If the operating time is 
still too short even after the battery is fully charged, the 
battery has worn out and can no longer be used. 
VQT1D97(ENG).book  104 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
105VQT1D97
This unit cannot be 
operated though it 
is turned on.
This unit does not 
operate normally.≥The unit cannot be operated unless you open the LCD 
monitor.
≥Remove the SD card then press the RESET button. 
(
l109) If normal conditions are not restored yet, 
remove the battery or AC adaptor, wait about 1 minute 
and then reconnect the battery or AC adaptor. Then 
about 1 minute later, turn on the power again. 
(Conducting the above operation when the access 
lamp is on may destroy the data on the card.)
The screen has 
changed suddenly.≥Has the demonstration started?
#If you set [DEMO MODE] to [ON] without inserting a 
card in video recording mode or picture recording 
mode, the unit is automatically set to the demonstration 
mode for introducing its functions. Normally this should 
be set to [OFF]. Press the MENU button, then select 
[SETUP] # [DEMO MODE] # [OFF] and press the 
cursor button in the center.
A function 
indication such as 
the remaining time 
indication or the 
elapsed time 
indication is not 
shown.≥If you set [SETUP]>[DISPLAY]>[OFF], indications 
other than warnings and date indications disappear.
ProblemCheck points
VQT1D97(ENG).book  105 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
106VQT1D97
Recording does not 
start although the 
power is supplied 
to this unit and the 
SD card is correctly 
inserted.≥Has the SD card’s write protect switch been set to 
LOCK?
#No recording is possible while the write protect switch 
is set to LOCK. (l22)
≥Is the memory of the card full?
#If the card has no more available memory, free up 
some memory by deleting unnecessary scenes (l70) 
or use a new card.
≥Is the unit set to the video recording mode or picture 
recording mode?
#No recording is possible unless the mode dial is at   
or .
≥Is the card/battery door open?
#If the card/battery door is open, this unit will not 
operate normally. Close the card/battery door and slide 
the card/battery door lock to LOCK.
Recording stops 
suddenly during 
motion picture 
recording on a 
card.≥When using an SD card on which data has been 
written many times and the data writing speed has 
reduced, the recording may suddenly stop during 
motion picture recording.
#Use a card recommended as suitable for motion 
picture recording. (l22)
If the recording stops even when a suitable SD card is 
used, back up the data on the card to a computer, etc. 
and then format the card. (l74)
Recorded still 
pictures are not 
clear.≥Are you trying to record small or finely detailed 
objects with [PICT. QUALITY] set at [ ]?
#If you try to record small or finely detailed objects with 
[PICT. QUALITY] set at [ ], the images may break 
up into a mosaic-like pattern. Record with 
[PICT. QUALITY] set at [ ] instead. (l49)
ProblemCheck points
VQT1D97(ENG).book  106 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
107VQT1D97
Auto focus 
function does not 
work.≥Is manual focus mode selected?
#Set the unit to auto focus mode by pressing the AUTO 
button.
≥Are you trying to record a scene which is hard to 
bring into focus in auto focus mode?
#There are some recording subjects and surroundings 
for which the auto focus does not operate correctly. 
(l115) If so, use the manual focus mode to adjust the 
focus. (l59)
Sound is not 
played back from 
the built-in speaker 
of this unit.≥Is the volume too low?
#During playback, press the volume button to display 
the volume indication and adjust it. (l66)
During playback, 
the sound from the 
camera’s motor is 
heard in the 
recording.≥This is a mechanical sound of the camera, but it is not 
a malfunction.
≥Are there drops of water on the microphone?
#The recorded mechanical sound may become louder 
and the microphone’s sensitivity may decrease when 
there are drops of water on the microphone.
Wipe off any drops of water and then leave the unit to 
dry naturally.
The speaker 
volume during 
playback is low.≥Are there drops of water on the microphone?
#The volume of the output sound may decrease when 
the speaker is wet. 
After wiping off any drops of water and then leaving the 
unit to dry naturally, it will return to normal.
Although this unit 
is correctly 
connected to a TV, 
playback images 
cannot be seen.
The playback 
images are 
squeezed 
horizontally.≥Have you selected video input on the TV? 
#Please read the operating instructions of your TV and 
select the channel that matches the input used for the 
connection.
≥Is the [TV ASPECT] setting correct?
#Change the setting to match the aspect ratio of the TV.
Press the MENU button, then select [SETUP] # 
[TV ASPECT] # [16:9] or [4:3] and press the cursor 
button in the center.
ProblemCheck points
VQT1D97(ENG).book  107 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
108VQT1D97
Scenes or files 
cannot be deleted 
or edited.≥Are the scenes or the files locked?
#Locked scenes or files cannot be deleted. Release the 
lock setting. (l72)
≥It may not be possible to delete scenes that are 
displayed as [ ] on the thumbnail display. If the 
scenes are unnecessary, format the card to erase the 
data. (l74) Please be aware that if the card is 
formatted then all the data recorded on the card will 
be erased.
≥If the SD card’s write-protect switch is set to LOCK, 
then deletion is disabled. (l22)
The images on the 
SD card do not look 
normal.≥The data may be destroyed. It may have been 
destroyed by static or electromagnetic waves. Store 
important data on a computer or other products as 
well.
Even if the card is 
formatted, it cannot 
be used.≥Either this unit or the card may be damaged. Please 
consult a dealer. Information about cards that can be 
used on this unit. (l22)
If the SD card is 
inserted in this 
unit, it is not 
recognized.≥Is an SD card formatted on a computer inserted?
#Use this unit to format SD cards. Please be aware that 
if an SD card is formatted, then all the data recorded on 
the card will be erased. (l74)
The indication 
disappears.
The screen is 
frozen.
No operation can 
be performed.≥Is this unit connected to a computer?
#No operation can be performed on this unit when it is 
connected to a computer.
≥Turn off the power to this unit. If the power cannot be 
turned off, remove the SD card then press the RESET 
button or remove the battery or AC adaptor and then 
reattach it. After that, turn on the power again. If 
normal operation is still not restored, detach the 
power connected, and consult the dealer who you 
purchased this unit from.
ProblemCheck points
VQT1D97(ENG).book  108 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
109VQT1D97
“PUSH THE RESET 
SWITCH.” is 
displayed.≥The unit has automatically detected an error. To 
protect the data, remove the SD card and then press 
the RESET button with a pointed object. This will 
restart the unit.
≥If you do not press the RESET button, the power to 
this unit is turned off automatically about 1 minute 
later.
≥Even after you press the RESET button, the indication 
may still appear repeatedly. If so, this unit needs 
repair. Detach the power connected, and consult the 
dealer who you purchased this unit from. Do not 
attempt to repair the appliance by yourself.
If the SD card is 
inserted in another 
device, it is not 
recognized.≥Check that the device is compatible with the capacity 
or type of SD card (SD Memory Card/SDHC Memory 
Card) that you inserted.
#Refer to the operating instructions of the device for 
details.
ProblemCheck points
VQT1D97(ENG).book  109 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							Others
11 0VQT1D97
With a computer
ProblemCheck points
Even if connected 
by the USB cable, 
this unit is not 
recognized by the 
computer.≥The USB function selection screen does not appear if 
the USB cable is connected while the menu screen is 
displayed.
#Close the menu screen before connecting the USB 
cable.
≥Is the AC adaptor connected?
#Use the AC adaptor when connecting the unit and a 
computer.
≥Select another USB terminal on the computer.
≥Check the operating environment. (l84)
≥Disconnect the USB cable, turn the unit off then on 
and then reconnect the USB cable.
When the USB 
cable is 
disconnected, an 
error message will 
appear on the 
computer.≥(For Windows) 
To disconnect the USB cable safely, double-click the  icon in the task tray and follow the instructions 
on the screen.
≥(For a Macintosh)
When the drive icon is displayed on the desktop, drag 
the icon into the Trash and then disconnect the USB 
cable.
VQT1D97(ENG).book  110 ページ  ２００７年３月２０日　火曜日　午後５時３３分