Panasonic Sdr S10 Operating Instructions Manual

							71VQT1D97
Editing
then press the cursor button 
in the center.
The selected scene is encircled by a 
red frame.
≥When the cursor button in the 
center is pressed again, the 
selected scene will be canceled.
≥Up to 50 scenes can be set in 
succession.
4(Only when [SELECT] is selected in 
step 2)
Press the   button.
5When the confirmation 
message appears, select 
[YES], then press the cursor 
button in the center.
(Only when [SELECT] is selected in 
step 2)
To continue deleting other scenes
Repeat steps 3-5.
To stop halfway through the 
deletion
Press the MENU button.
≥The scenes are deleted from the end 
of the thumbnail display. All scenes 
that were deleted before the deleting 
was stopped cannot be restored.
To complete editing
Press the MENU button.
∫Deleting still picture files 
recorded on an SD card by 
other products
A still picture file (other than JPEG) that 
cannot be played back on this unit may 
be erased.
≥Scenes which cannot be played back 
(the thumbnails are displayed as [ ]) 
cannot be deleted.
≥In case of [ALL], the deletion may take 
time if there are many scenes.
≥Do not turn off this unit while deleting.
≥When you delete scenes, use a battery 
with sufficient battery power or use the 
AC adaptor.
≥Do not open the card/battery door 
while deleting. The deletion will stop.
≥The locked scenes cannot be deleted.
≥If you delete scenes recorded on other 
products with this unit, all the data 
related to the scenes may be deleted. 
≥If files conforming to DCF standard are 
deleted, all the data related to the files 
will be deleted.
VQT1D97(ENG).book  71 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							72VQT1D97
Editing
Scenes can be locked so that they are 
not deleted by mistake. (Even if you lock 
some scenes on an SD card, formatting 
the SD card will delete them.)
¬Rotate the mode dial to select 
 or  .
1(For motion pictures)
Press the MENU button, then 
select [PLAY SETUP]  # 
[LOCK SET] # [YES] and then 
press the cursor button in the 
center.
(For still pictures)
Press the MENU button, then 
select [PICT. SETUP]  # 
[LOCK SET] # [YES] and then 
press the cursor button in the 
center.
2Select the scene to be locked, 
then press the cursor button 
in the center.
[ ] display appears and the 
selected scene is locked.
≥Press the cursor button again to 
release the lock setting.
≥You can also select multiple 
scenes in succession.
To complete the settings
Press the MENU button.
Locking scenes
This is for preventing scenes 
from being deleted by mistake.
VQT1D97(ENG).book  72 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							73VQT1D97
Editing
You can write the data of the still pictures 
to be printed and the number of prints 
(DPOF data) onto the SD card.
¬Rotate the mode dial to select 
.
1Press the MENU button, then 
select [PICT. SETUP] # 
[DPOF SET] # [SET] and then 
press the cursor button in the 
center.
2Select the file to be set, then 
press the cursor button in the 
center.
The number of prints set to be in 
DPOF is displayed.
3Press the cursor button up or 
down to select the number of 
prints, then press the cursor 
button in the center.
≥You can select from 0 to 999. (The 
selected number of pictures can 
be printed with the printer 
supporting DPOF.)
≥To cancel the setting, set the 
number of prints to [0].
≥You can also select multiple files in 
succession.
To complete the settings
Press the MENU button.
To cancel all DPOF settings
Press the MENU button, then select 
[PICT. SETUP] # [DPOF SET] # 
[CANCEL ALL] and then press the 
cursor button in the center.
≥When the confirmation message 
appears, select [YES], then press the 
cursor button in the center.
∫What is DPOF?
DPOF stands for Digital Print Order 
Format. This enables picture printing 
information to be written onto an SD card 
so that it can be used on a system 
supporting DPOF.
≥The DPOF setting can be established 
for up to 999 files.
≥DPOF setting made on other devices 
may not be recognized by this unit. 
Please perform the DPOF settings on 
this unit.
≥You cannot add the recording date to 
pictures to be printed with the DPOF 
settings.
DPOF setting
This is for writing the printing 
data on an SD card.
VQT1D97(ENG).book  73 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							74VQT1D97
Editing
Card management 
Please be aware that if an SD card is 
formatted, then all the data recorded 
on the card will be erased. Store 
important data on a computer, etc.
We recommend using MotionSD 
STUDIO etc. to acquire data recorded on 
this unit. (l82)
1Press the MENU button, then 
select [SETUP] # 
[FORMAT CARD] # [YES] and 
then press the cursor button 
in the center.
2When the confirmation 
message appears, select 
[YES], then press the cursor 
button in the center.
≥When formatting is complete, 
press the MENU button to exit the 
message screen.
≥Use this unit to format SD cards. If an 
SD card is formatted on other products 
(such as a computer), the time spent 
for recording may become longer and 
you may not be able to use the SD 
card.≥Depending on the type of SD card 
being used, it may take time to format.
≥During formatting, do not turn this unit 
off.
≥When you format the SD card, use a 
battery with sufficient battery power or 
the AC adaptor.
≥Do not open the card/battery door 
while formatting.
Formatting an SD card
This is for initializing cards.
VQT1D97(ENG).book  74 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							75VQT1D97
With other products
With other pro ducts
With a TV
The motion pictures and still pictures 
recorded by this unit can be played back 
on a TV.
≥
Use the AC adaptor to free you from 
worrying about the battery running down.
1Slide the terminal cover lock 
to OPEN and then open the 
terminal cover.
2Connect this unit to the TV.
AAV cable (supplied)
≥Insert the plugs as far as they will 
go.
≥Do not use any other AV cables 
except the supplied one.
3Rotate the mode dial to select 
 or  .
4Change the input channel on 
the TV.
≥The channel set will differ 
depending on the terminal to which 
the unit is connected.
5Start playback on this unit.
The image and audio are output on 
the TV.
∫If the image or audio from 
this unit is not output on 
the TV
≥Check that the plugs are inserted as 
far as they can go.
≥Check the connected terminal.
≥Check the TV’s input setting (input 
switch). (For more information, 
please read the operating 
instructions for the TV.) 
≥If you have a TV with an SD card slot, 
the motion pictures and still pictures 
recorded on the SD card maybe 
played back on the TV. (Refer to the 
operating instructions of the TV for 
details about TV compatibility.)
≥If the images are not displayed 
correctly on a wide-screen TV, adjust 
the aspect setting on the TV. (Refer to 
the operating instructions of the TV for 
details.) If the pictures are displayed 
squeezed horizontally on a regular TV 
(4:3), change the [TV ASPECT] setting 
on this unit. (l76)
Playback on TV
VIDEO IN
AUDIO IN
A
VQT1D97(ENG).book  75 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							76VQT1D97
With other products
∫To watch images with a 
16:9 aspect ratio on a 
regular TV (4:3)
When playing back motion pictures 
recorded with a 16:9 aspect ratio 
([ASPECT] was set to [16:9]) on a TV 
with a 4:3 aspect ratio, the images may 
be squeezed horizontally. In this case, 
change the menu setting to play back the 
pictures in the original aspect ratio. 
(Depending on the TV setting, the 
pictures may not be displayed correctly. 
For more information, please read the 
operating instructions of your TV.)
Press the MENU button, then 
select [SETUP] # [TV ASPECT] 
# [4:3] and then press the cursor 
button in the center.
Example of images with a 16:9 aspect 
ratio on a regular TV (4:3)
≥This function’s default setting is [16:9].
∫To display the on-screen 
information on the TV 
screen
The information displayed on the screen 
(operation icon, time code, etc.) can be 
displayed on the TV.
Press the MENU button, then 
select [SETUP] # [EXT. DISPLAY] 
# [ON] and then press the cursor 
button in the center.
≥Set [SETUP] # [EXT. DISPLAY] # 
[OFF] to erase the information.
≥The screen on this unit will not change.
[TV ASPECT] setting
[16:9][4:3]
VQT1D97(ENG).book  76 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							77VQT1D97
With other products
With a DVD recorder
If you have a DVD recorder with an SD 
card slot, images recorded by this unit 
can be copied (dubbed) onto the hard 
disk or a DVD disc.
Refer to the operating instructions of 
your DVD recorder for information about 
whether or not it supports copying 
(dubbing) from an SD card.
≥If your DVD recorder does not support 
copying (dubbing) from an SD card, 
connect this unit and the DVD recorder 
with the AV cable (supplied) and then 
copy (dub). (l78)
Insert the SD card into the SD 
card slot on the DVD recorder, 
then copy (dub) the contents onto 
the hard disk or a disc.
≥For details on how to copy (dub) the 
images, refer to the operating 
instructions of the DVD recorder.
≥The images recorded on the hard disk or 
DVD-RAM are converted to the 
DVD 
video recording format. Once converted, 
you cannot copy them at high speed onto 
a DVD-R or copy them onto an SD card 
using the MPEG2 format.
Copying (dubbing) 
recordings onto a DVD 
recorder
If you record (dub) images directly 
from the SD card or with the AV cable 
and then play them back on a wide-
screen TV, they may be squeezed 
horizontally. In this case, refer to the 
operating instructions of the device 
you are recording (dubbing) to or read 
the operating instructions of the wide-
screen TV and set the aspect setting 
to 16:9 (Full).
VQT1D97(ENG).book  77 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							78VQT1D97
With other products
With a VCR
You can record (dub) images played 
back on this unit onto other video 
devices.
≥Use the AC adaptor to free you from 
worrying about the battery running 
down.
1Slide the terminal cover lock 
to OPEN and then open the 
terminal cover.
2Connect this unit and a video 
device.
AAV cable (supplied)
≥Insert the plugs as far as they will 
go.
3Rotate the mode dial to select 
.
4Change the input channel on 
the video device and TV.
≥The channel set will differ 
depending on the terminal to which 
the unit is connected.
5Start playback on this unit.
Then start recording on the 
connected device.
≥See the operating instructions of 
the video device for details.
Recording (dubbing) 
images onto other 
video devices
VIDEO IN
AUDIO IN
A
VQT1D97(ENG).book  78 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							79VQT1D97
With other products
To stop recording (dubbing)
Stop recording on the connected device.
Then stop playback on this unit.
≥If the date and time display and 
function indication are unnecessary, 
cancel them before recording 
(dubbing). (l40, 76)
With a printer 
(PictBridge)
To print pictures by directly connecting 
this unit to the printer, use a printer 
compatible with PictBridge. (Read the 
operating instructions for the printer.) 
≥Use the AC adaptor to free you from 
worrying about the battery running 
down.
¬Turn on the unit.
1Slide the terminal cover lock 
to OPEN and then open the 
terminal cover.
VQT1D97(ENG).book  79 ページ  ２００７年３月２０日　火曜日　午後５時３３分 
						

							80VQT1D97
With other products
2Connect this unit to a printer.
AUSB cable (supplied)
≥Insert the plugs as far as they will 
go.
≥Do not use any other USB 
connection cables except the 
supplied one. (Operation is not 
guaranteed with any other USB 
cables.)
3Press the cursor button up or 
down to select [PictBridge], 
then press the cursor button 
in the center.
≥The [ ] indication 
appears on this unit’s screen.
4Select a file to be printed, then 
press the cursor button in the 
center.
The number of pictures set is 
displayed.
5Press the cursor button up or 
down to select the desired 
number of prints, then press 
the cursor button in the 
center.
≥You can set up to 9 prints.
≥To cancel the setting, set the 
number of prints to [0].
≥Up to 8 files displayed on a page 
can be set in succession by 
repeating steps 4 and 5.
6Press the MENU button to 
display the PictBridge menus.
7Select the date print setting on 
[DATE PRINT].
≥If the printer is not capable of date 
printing, this setting is unavailable.
A
VQT1D97(ENG).book  80 ページ  ２００７年３月２０日　火曜日　午後５時３３分