Panasonic Ramsa Audio Mixer Wr Da7 Users Guide

10-2 AUX Section Controls
The AUX section contains a LEVEL ON/OFFknob and LED buttons for
AUXs 1-6, PRE(pre-fader), and FADER CONTROL.
[LEVEL] ON/OFF Knob
To assign an aux to a selected channel, press one of the AUX 1-6
LED buttons to select it (green), and then press the LEVEL
ON/OFFknob to activate the aux assignment.  or  status is
shown in the [CHANNEL] window and in the respective [FADER
CONTROL>AUX]window. The AUXLED field of the respective
Channel Stripalso reflects the aux assignment.
Turn the...

FADER CONTROLLED Button
When active (red), a window from the [FADER CONTROL]window group is
displayed in the LCD. When the FADER CONTROLLED button is activated,
the [AUX] window last used is displayed on the LCD. 
When the FADER CONTROLLED button is off, parameter adjustments can
be seen in the [CHANNEL] window.
When a [FADER CONTROL]window is displayed, press an AUX 1-6LED
button to display the respective [AUX]window in the LCD. Faders will react
to display the selected aux send for each channel.
Level...

10-3 FADER CONTROL Window
This window displays the aux send status of all the input channels. You can
set pre-fader or post-fader selections and the aux send on or off status of
each channel from this window. This window is displayed when the [FADER
CONTROL]LED button is activated (red). The [FADER CONTROL>AUX]
window displayed will change when you press any of the AUX 1-6LED
buttons, and the faders will follow.
[FADER CONTROL]Window, Elements
and Buttons
The post-fader and pre-fader selection buttons...

[Level Meter]Display
Aux send level meters on the right of the individual channel
areas display the aux send level for the selected channel. All 1
through 32 send levels can be monitored from the [FADER
CONTROL]windows. Moving the fader for the selected channel
will control the send output level of the respective aux send.
Rotating the LEVEL ON/OFFknob will also adjust the selected
level. If the [UTILITY>CONFIG]window [AUTO DISP CHANGE]
item is set to  , the LCD display will change to the [CHANNEL]...

DA7 Users’ Guide11-1
11
MIDI
Press the MIDIbutton in the SETUPsection of the Top Panel. A window
from the [MIDI]window group will appear in the LCD. Each time you press
the MIDIbutton, the [SETUP], [PRG ASGN], [CTRL ASGN], [BULK], and
[MIDI RMT]windows are shown in sequence in the LCD. 
Appendix Gdetails the technical information on MIDI communications.
11-1 MIDI, SETUP Window
The [MIDI>SETUP]window shows the configuration settings for MIDI
operations.
The DA7has ports for MIDI INand MIDI OUTand serial...

Receive Indicator
The window has receive indicators in the [taskbar]. A  indicator blinks
when data is received at the MIDI INconnection, an  indicator blinks
when data is received at the RS 422/485 terminal, and a  indicator
blinks when data is received at the TO PCterminal.
[SERIAL I/O SETUP]Area
[PORT SELECT]Area
The DA7 has a TO PCconnector port and an RS422/485 serial port on the
Rear Panel. These ports are used for attaching a Mac O/S or Windows O/S
computer platform to the DA7. Only one port can...

Chapter 11 
DA7 Users’ Guide11-3
11
MIDI
[MIDI SETUP]Area
Here, the direction of messages (serial data) coming from and going to MIDI
IN, MIDI OUT, and TO PCis set. Select one of these four combinations to
set the direction of data:
Status 1: When  is set to  and  is set to  , the DA7
cannot communicate with the personal computer. Data can be
transmitted and received between the DA7and a MIDI device. A
message is input from the MIDI device to the MIDI INterminal, while
the DA7outputs a message to the...

Button
Set the MIDIoutput port by pressing the ENTERbutton. Use the same 
with the  . Cursorto  on the  line, and perform the
same step described in  setting.
Cursorto  on the  line, and perform the same step described in
setting. The DA7 sends a message to the selected port, either [MIDI]
or [toPC]. 
Button
Activate the program change command by pressing the ENTERbutton to set
pass-through of receiving, transmitting, and inputting signals on or off.
Button
Activate the control change command by pressing...

Button
Set the real-time message input and output port by pressing the ENTER
button. Activate a port to send and receive MIDI clock and other real-time
messages.
Cursorto the  line, and press the ENTERbutton to display either 
or 
.
Button
This button sets the MMC(MIDI machine control) output destination, either
or 
.Cursorto the [PORT]column, and press the ENTERbutton to
toggle the selections. Cursorto the [CH] column, and rotate the JogDial to
select a MIDI channel to match the external MIDI device....

11-2 MIDI, PRG ASGN (Program Assign) Window
Assign scene memory numbers to the change table to be used by the DA7in
the [PROGRAM CHANGE TABLE] area. This is useful when you are
exchanging existing scene memories for new ones.
To execute , as in calling up a mixed scene, check the 
settings on the [MIDI>SETUP]window again.
[PROGRAM CHANGE TABLE] Area
Select a program change table. Rotate the JogDialto select a program
change number from 1 through 128. The initial setting is 1 through 50. [NO
ASSIGN]is set...