Panasonic Ramsa Audio Mixer Wr Da7 Users Guide

Chapter 11 
DA7 Users’ Guide11-7
11
MIDI
[SCENE LIST TABLE] Area
Rotate the JogDialto select a scene memory number.
[ASSIGN] Indicator
An arrow indicates a status. The scene memory is registered to the
selected table by pressing the ENTERbutton. At that time, the
arrow symbol is highlighted and shows the selection.
Button
Initialize the table. Cursorto the  button, and press the ENTER
button. This function returns all the data in the change table to the state of
default.
Setting of Registration
Press the...

11-3 MIDI, CTRL ASGN (Control Assignment) Window
Change the DA7sinput and output channel assignments, fader position, etc.
with this window.
The [CONTROL CHANGE TABLE]consists of three columns: for item
numbers, for parameters, and for channels. The control change table has
item numbers 0 through 119, of which 6, 38, and 96 through 101 cannot be
used. The data of the control change table can be stored in an external
device as backup data by the MIDI bulk dump function. 
To execute  in calling up a mixed...

Button
Select a parameter to be registered in the [CONTROL CHANGE TABLE]
by rotating the JogDial.
Button
Select a channel to be registered in the [CONTROL CHANGE TABLE]
by rotating the JogDial.
[Assign ] Element
This area indicates status. The parameter and channel are registered to
the selected table by pressing the ENTERbutton. At that time, the
[Assign ]is highlighted and shows the selection. If a combination of
the selected parameter and channel is not acceptable, the arrow is
distorted, showing that...

11-4 MIDI, BULK (Bulk Out) Window
Data can be sent and received between two DA7s, or between the DA7and a
MIDI datafiler, or a personal computer. [MIDI>BULK]may be used to save
and read DA7settings and library data from/to other devices as backup data,
or to exchange data between two DA7s to create common settings and
library data. It takes about 7 minutes to transmit all 720 kB of data through
the TO PCport at a rate of 125 kbps.
[BULK I/O DATA SELECT]Area
Button
Select setup data of the current device...

Button
Select an EQ library by pressing the ENTERbutton.
[EQ library number/title ]
Select an EQ library number by rotating the JogDial. Choose ALL or
1-50. The initial setting is ALL.
Button
Select a dynamics library by pressing the ENTERbutton.
[Dynamics library number/title  ]
Select a dynamics library number by rotating the JogDial. Choose ALL
or 1-50. The initial setting is ALL.
Button
Select automation event data by pressing the ENTERbutton.
[Automation event number/title  ]
Select an automation...

[Rx]
Switch bulk command reception  or  by pressing the
ENTERbutton.When this is OFF, the DA7ignores any of
commands or data sent by external devices.
Button
Begin bulk data reception from another DA7by pressing the ENTER
button. If a MIDI device other than DA7is connected, you need to have
the device start sending data. 
Button
Begin bulk data transmission to an outside device by pressing the
ENTERbutton.
Data being received or sent is shown every 10% during [REQUEST]or
[BULK OUT]communication. To...

Chapter 11 
DA7 Users’ Guide11-13
11
MIDI
Setting of Bulk Command Reception
Switch the setting  or  to receive a bulk data or bulk out transmission
request from outside by pressing the ENTERbutton.
You can choose whether or not to ignore a request made by other devices.
Cursorto [Rx], and press the ENTERbutton. Each time the button is pressed,
and toggles.
Data Transmission Request and Transmission
Press the  button to request transmission of selected data from
another DA7, and load the data. To cancel...

11-5 MIDI, REMOTE Windows
These windows display and set MIDI remote operations for the external MIDI
devices, and edit MIDI remote libraries. Set registration of the MIDI remote
to the fader layers on the User Customize Window. Execute the MIDI remote
by using the MIDI control change command.
For more information, see Section 16-4, Utility, User Custom (USER
CSTM) Window.
[REMOTE]Window
[FADER SELECT] Area
Choose a page for remote by selecting either the  or  button, and
pressing the ENTERbutton.
Chapter...

Chapter 11 
DA7 Users’ Guide11-15
11
MIDI
[EDIT]
This button sets the edit mode.
[TITLE]
This area displays a remote library title.
Button
This button calls up the MIDI Remote Library window.
[SOLO]
Use the [SOLO]switch to assign a control change message that is
predetermined in an external MIDI device. Cursorto the operator button, and
press the ENTERbutton to open the [REMOTE CONTROL EDIT]window
for the edit of the message. You can enter the name for each operator in the
[TITLE]field right under the...

[FADER]
Use the [FADER]to assign a control change message. Functions and
operations are the same as the [SOLO]switch.
The following operators reflect the MIDI messages sent from the external
devices, if the [MIDI REMOTE] is active and the channels are assigned in the
[UTILITY>USER CSTM]window(See page 16-12) and the  is
selected in the [MIDI REMOTE] [Edit]window(See below). 
: SOLO LEDkeys, ON LEDkeys and FADERs on the Top Panel
: SOLO, ON, PA Nand FADERAreas on the LCDscreen
[Edit]Window
[REMOTE COMMAND...