Panasonic Projector PT-DZ10KU User Manual

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 111
[LAMP POWER]
Switch the brightness of the lamp according to the operating environment of the projector or the purpose.
1) Press as to select [LAMP POWER].
2)  
Press 
 qw to switch the item.
[HIGH]*1Select when high luminance is required.
[MIDDLE]
*1Select when using the projector with slightly reduced luminance compared to [HIGH].
[NORMAL]
*2Select when high luminance is required.
[ECO] Select when high luminance is not required.
*1 Only for...

Chapter 4 Settings — [PROJECTOR SETUP] menu
112 - ENGLISH
5) Press as to select [MODE].
6)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Does not correct the brightness of the screen by the brightness sensor.
[AUTO] Corrects the brightness of the screen by the brightness sensor.
Automatically corrects screen brightness when lamp brightness changes.
[PC] Synchronizes nine or more projectors through a computer using the dedicated software “Multi 
Projector...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 113
Note
 fWhen [MODE] in [BRIGHTNESS CONTROL  SETUP] is set to [AUTO] or [PC], keep the shutter open for at least two minutes to perform the 
brightness sensor calibration after completed the [BRIGHTNESS CONTROL SETUP] setting.
 f If the shutter is closed within approx. 10 minutes after the lamp has turned on while [MODE] in [BRIGHTNESS CONTROL  SETUP] is set to 
[AUT

O] or  [PC], brightness cannot be measured. Therefore, brightness may be corrected...

Chapter 4 Settings — [PROJECTOR SETUP] menu
114 - ENGLISH
When [MODE] of [BRIGHTNESS CONTROL SETUP] is set to 
[AUTO] and [LINK] is set from [GROUP A] to [GROUP D]
The screen shows the status of the brightness control of 
synchronized projectors (up to eight units), including the projector 
being controlled through the on-screen menu.
2 1
3
4
5 
7
8
1:
2:
3:
4:
5:
6:
7:192. 168. 30.   2
192. 168. 30.   3
192. 168. 30.   4
LINK
UPDATE PROJECTOR
GROUP A
PROJECTOR2
PROJECTOR3
BRIGHTNESS CONTROL STATUS
MENU...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 115
Brightness control adjustment procedure example
The steps exemplify an adjustment to link the brightness of eight projectors connected in a network.
1) Connect all projectors to the hub using LAN cables. (x   page   136)
2)  
Switch on all projectors and start projection.
3)

 
Set [LAMP
  SELECT] to either [DUAL] or [SINGLE] for all projectors.
4)
 
Set [MODE] of [BRIGHTNESS CONTROL
  SETUP] to [OFF], and select [APPLY], and then press the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
116 - ENGLISH
[SCHEDULE]
Set the command execution schedule for each day of the week.
Enabling/disabling the schedule function
1) Press as to select [SCHEDULE].
2)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[OFF] Disables the schedule function.
[ON] Enables the schedule function. Refer to “How to assign a program” (
x
  page   116) or “How to set a 
program” (x
  page   116) for how to set the schedule.
Note
 fWhen...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 117
[COMMAND]Detailed settings of 
[COMMAND] Description
[INPUT] [VIDEO]
Switches the input to VIDEO.
[RGB1] Switches the input to RGB1.
[RGB2] Switches the input to RGB2.
[DVI
- D]Switches the input to DVI
- D.
[HDMI] Switches the input to HDMI.
[SDI1]
*1
(PT- DZ13KU, PT- DS12KU)
Switches the input to SDI1.
(PT
-

DZ10KU)
Switches the input to SDI.
[SDI2]
*2Switches the input to SDI2.
[LAMP SELECT] [DUAL]
Turns on two lamps.
[SINGLE] Turns on one...

Chapter 4 Settings — [PROJECTOR SETUP] menu
118 - ENGLISH
[HDMI]Sets the input to HDMI.
[SDI1]
*1/[SDI]*2Sets the input to SDI/SDI1.
[SDI2]
*1Sets the input to SDI2.
*1 Only for PT- DZ13KU, PT- DS12KU
*2  
Only for PT-
 DZ10KU
[RS-232C]
Set the communication conditions of the / terminal.
Setting the communication condition of the  terminal
1) Press as to select [RS-232C].
2)  
Press the  button.
 f The  [RS-232C]  screen is displayed.
3) Press  as to select [(IN) BAUDRATE].
4)  
Press 
 qw to switch the...

Chapter 4 Settings — [PROJECTOR SETUP] menu
ENGLISH - 119
2) Press the  button.
 fThe  [RS-232C]  screen is displayed.
3) Press  as to select [RESPONSE(ID ALL)].
4)  
Press 
 qw to switch the item.
[ON] Returns the response when the ID setting is ALL.
[OFF] Does not return the response when the ID setting is ALL.
5) Press as to select [GROUP].
6)  
Press 
 qw to switch the item.
[A] - [Z] Controls multiple projectors simultaneously by sending the ID of RS - 232C. You can set groups from 
[A] to [Z]. The...

Chapter 4 Settings — [PROJECTOR SETUP] menu
120 - ENGLISH
[REMOTE2 STATUS]Displays the control status of the REMOTE2.
[AC VOLTAGE] Displays the status of the AC voltage.
[COOLING CONDITION] Displays the set cooling conditions. When [AUTO] is set, automatically recognized result is displayed.
[SIGNAL INFORMATION] [MEMORY NO.]
Displays the memory number of the input signal.
[INPUT] Displays the input terminal currently selected.
[SIGNAL NAME] Displays the input signal name.
[SIGNAL FREQUENCY] Displays the...