Panasonic Projector PT-DZ10KU User Manual

Chapter 4 Settings — [NETWORK] menu
ENGLISH - 151
[User] account
1
2
3
5 4
1 [Account]
Displays the account to change.
2
 
[New][User name]
Enter the desired new user name. (Up to 16 characters in single 
byte) 3

 [New][Password]
Enter the desired new password. (Up to 16 characters in single 
byte)
4
 
[New][Password(Retype)]
Enter the desired new password again.
5

 
[OK]
Determines the change of password.
[Change password] (For user rights)
Only the change of password is enabled under the user...

Chapter 4 Settings — [NETWORK] menu
152 - ENGLISH
Control page
1
2
3
4
5
6
7
1 [Tools][Info][Help]Tabs for selecting the setting, information, or help page of the 
projector.
2
 
[POWER]
T

urns on/off the power.
3
 
[SHUTTER]
Switches the setting whether to use the shutter function 
(closing/opening of the shutter). 4

 [Input Select]
Controls input selection.
Not available when the power of the projector is turned of
f.
5
 
Menu screen control buttons
Navigates the menu screen.
6

 
Freeze/image...

Chapter 4 Settings — [NETWORK] menu
ENGLISH - 153
[Info] page
Click [Info] on the control page.
4
5
6
7
1
2
3
8
1 [Projector Name]
Displays the projector name.
2
 
[Mac Address]
Displays the MAC address.
3

 
[Lamp Hours]
Displays the runtime of the lamps (converted value).
4

 
[Power Status]
Displays the status of the power

. 5
 [Source]
Displays the selected input.
6
 
[Lamp Mode]
Displays [LAMP

 POWER] (x   page   111).
7
 
[Error Status]
Displays the error status.
8

 
[Exit]
Returns to the...

154 - ENGLISH
Chapter 5 Maintenance
This chapter describes methods of inspection when there are problems, maintenance, and replacement of the units.   

Chapter 5 Maintenance — Lamp/temperature/filter indicators
ENGLISH - 155
Lamp/temperature/filter indicators
When an indicator lights up
If a problem should occur inside the projector, the lamp indicators /, the temperature indicator , and the filter 
indicator  will inform you by lighting or flashing. Check the status of the indicators and manage the indicated problems as follows.
Attention
 fWhen switching of f the projector to deal with problems, make sure to follow the procedure in “Switching of f the...

Chapter 5 Maintenance — Lamp/temperature/filter indicators
156 - ENGLISH
Temperature indicator 
Indicator statusLighting in red Flashing in red
(2 times) Flashing in red
(3 times)
Status Warm-up status Internal temperature is high 
(warning).Internal temperature is high 
(standby status).The cooling fan has 
stopped.
Cause
 f Did you turn on the power 
when the temperature 
was low (around 0

  °C 
(32
  °F))?
 fIs the air intake/exhaust port blocked?
 fIs the room temperature high?
 fIs the filter...

Chapter 5 Maintenance — Maintenance/replacement
ENGLISH - 157
Maintenance/replacement
Before performing maintenance/replacement
 fMake sure to turn of f the power before maintaining or replacing the unit. ( x pages 52, 55)
 fWhen switching of

f the projector, make sure to follow the procedures in “Switching off the projector” (x   page   55).
Maintenance
Outer case
Wipe off dirt and dust with a soft, dry cloth.
 fIf the dirt is persistent, soak the cloth with water and wring it thoroughly before wiping....

Chapter 5 Maintenance — Maintenance/replacement
158 - ENGLISH
Cleaning the air filter unit
Remove the air filter unit beforehand with the previously described procedure of “Removing the air filter unit”.
Fig. 1Fig. 2
1) Wash the air filter unit. (Fig. 1)
i) Soak the air filter unit in cold or warm water and then lightly rinse it.
 fDo not use cleaning tools such as brushes.
 fWhen rinsing, hold the frame of the air filter unit without putting strong pressure on the filter unit.
ii)

 
Rinse the air...

Chapter 5 Maintenance — Maintenance/replacement
ENGLISH - 159
Replacing the unit
Air filter unit
If dirt does not come off even after the unit is maintained, it is time for the unit to be repla\
ced.
The Replacement Filter Unit (Model No.: ET
-
EMF320) is an optional accessory. To purchase the product, consult your dealer.
Replacing the air filter unit
Attention
 f Make sure to turn of f the power before replacing the air filter unit. fWhen attaching the unit, make sure that the projector is stable, and...

Chapter 5 Maintenance — Maintenance/replacement
160 - ENGLISH
Note
 fThe model numbers of accessories and optional accessories are subject to change without prior notice.
When to replace the lamp unit
The lamp unit is a consumable component. Since its brightness gradually \
decreases over time, it is necessary to replace the lamp unit 
regularly. The estimated duration before replacement is 2
  500 hours*1, but the lamp may go off before 2 500 hours*1 has elapsed depending 
on individual lamp...