Panasonic Projector PT-DZ10KU User Manual

Chapter 4 Settings — [3D SETTINGS] menu
ENGLISH - 91
[3D SETTINGS] menu
(Only for PT-DZ13KU, PT- DS12KU, PT- DW11KU)
On the menu screen, select [3D SETTINGS] from the main menu, and select \
an item from the 
sub-menu.
Refer to “Navigating through the menu” ( x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[3D SYSTEM SETTING]
Set a picture display method for use during 3D signal input as necessary\
 for the 3D system in use.
1) Press  as to select [3D...

Chapter 4 Settings — [3D SETTINGS] menu
92 - ENGLISH
[3D SYNC MODE]Items set in [3D SYNC1] Items set in [3D SYNC2]
[10] Stereo synch output Frame synch output
[11] 3D IR TRANSMITTER (+) output 3D IR TRANSMITTER (
-) output
6) When [1], [4], [7], or [10] is selected, press as  to select [STEREO SYNC OUTPUT DELAY], and press 
qw to set the amount of delay output.
[0us] - [25 000 us] Allows you to set in increments of 10   us.
 fT

o synchronize multiple projectors to display 3D images, use a frame synch...

Chapter 4 Settings — [3D SETTINGS] menu
ENGLISH - 93
Note
 fWhen set to [AUT O], [SIMULTANEOUS], [SIDE BY SIDE], [TOP AND BOTTOM], [LINE BY LINE], or [FRAME SEQUENTIAL], 3D images 
are not displayed in [3D SIMUL INPUT SETTING]. In [AUTO], however, this only occurs when 3D format can be recognized.
 f This may not function properly for some connected external devices.
[LEFT/RIGHT SWAP]
Display images by inverting the timing of horizontal image switching. Change the settings when there is something wrong...

Chapter 4 Settings — [3D SETTINGS] menu
94 - ENGLISH
[3D WAVEFORM MONITOR][OFF]
Hides the 3D waveform monitor.
[ON] Displays the 3D waveform monitor.
Note
 fThe [CLOCK PHASE] setting is enabled at simultaneous input of RGB1 and R\
GB2 to adjust the right eye image. fThis is disabled when [3D SYSTEM SETTING] is set to other than [SINGLE]. fThis is disabled when [3D 

TEST PATTERN] is displayed.
 fThis is disabled when [3D 

TEST MODE] is set to other than [NORMAL] or [SIDE BY SIDE].
 fThe 3D waveform...

Chapter 4 Settings — [3D SETTINGS] menu
ENGLISH - 95
[3D TEST PATTERN]
The 3D test pattern can be used to check operation and make adjustments even without a 3D signal.
1) Press as to select [3D TEST PATTERN].
2)  
Press 
 qw to switch the item.
Menu screen + Entry screen
Select a test pattern so that it is easy to check operations and make ad\
justments.
Menu screen + Left: white/
Right: black
Menu screen + Left: black/ Right: white
Note
 fThe 3D test pattern cannot be displayed when the following...

Chapter 4 Settings — [DISPLAY OPTION] menu
96 - ENGLISH
[DISPLAY OPTION] menu
On the menu screen, select [DISPLAY OPTION] from the main menu, and select an item from 
the sub-menu.
Refer to “Navigating through the menu” (x
  page   65) for the operation of the menu screen.
 fAfter selecting the item, press 

asqw to set.
[COLOR MATCHING]
Correct the color difference between projectors when using multiple projectors simultaneously.
Adjusting the color matching as desired
1) Press  as to select [COLOR...

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 97
Adjusting the color matching using a colorimeter
Use a colorimeter that can measure chromaticity coordinates and luminanc\
e to change the colors [RED], [GREEN], [BLUE], [CYAN], 
[MAGENTA], [YELLOW], or [WHITE] to desired colors.
1) Press as to select [COLOR MATCHING].
2)  
Press 
 qw to select [709MODE] or [MEASURED].
3)
 
Press the  button.
 f The  [709MODE] or [MEASURED MODE] screen is displayed.
4) Press  as to select [MEASURED DATA].
5)  
Press...

Chapter 4 Settings — [DISPLAY OPTION] menu
98 - ENGLISH
3) Press qw to switch the [SCREEN FORMAT] item.
 fThe items will switch each time you press the button.
Model No. [SCREEN FORMAT] Range when [SCREEN POSITION] is selected
PT
-

DZ13KU, PT
-
 DZ10KU [16:10]
Cannot be adjusted.
[4:3] Adjusts the horizontal position between 
-160 and 160.
[16:9] Adjusts the vertical position between 
-60 and 60.
PT
-

DS12KU [4:3]
Cannot be adjusted.
[16:9] Adjusts the vertical position between 
-132 and 131.
4) Press...

Chapter 4 Settings — [DISPLAY OPTION] menu
ENGLISH - 99
2) Press the  button.
 fThe  [AUTO SETUP] screen is displayed.
3) Press  as to select [POSITION ADJUST].
4)  
Press 
 qw to switch the item.
[OFF] Does not perform automatic adjustment.
[ON] Adjust the screen position and size when automatic setup is executed.
Adjusting signal level automatically
1) Press as to select [AUTO SETUP].
2)  
Press the  button.
 f The  [AUTO SETUP] screen is displayed.
3) Press  as to select [SIGNAL LEVEL ADJUST].
4)...

Chapter 4 Settings — [DISPLAY OPTION] menu
100 - ENGLISH
[DVI-D IN]
Switch the setting when the external device is connected to the  terminal of the projector and the image is not projected correctly.
1) Press as to select [DVI-D IN].
2)  
Press the  button.
 f The  [DVI-D IN] screen is displayed.
3) Press  as to select [EDID].
4)  
Press 
 qw to switch the item.
 fThe items will switch each time you press the button.
[EDID3] Recognizes movie-based video signals and still image signals automatically ....